Pro-dress FS936E Sharp Edge Drop Instruction Manual

Pro-dress FS936E Sharp Edge Drop

Product Information

Specifications

• Model: Anchor Line
• Regulation: (EU) 2016/425
• Manufacturing Dates: Various, refer to equipment label
• Notified Body: CE1019, CE0120, CE0321

Product Usage Instructions

1. Safety Precautions
   Before using the anchor line, ensure you have read and understood all safety precautions provided in the user manual.

2. Equipment Inspection
   Inspect the anchor line for any visible defects such as cuts, fraying, or damage before each use. Do not use if any damage is found.

3. Connecting the Anchor Line
   Ensure the anchor line is securely connected to a suitable anchor point according to safety regulations and guidelines.

4. Proper Use
   Use the anchor line only for its intended purpose as described in the user manual. Do not exceed the maximum weight capacity specified.

5. Maintenance
   Regularly inspect and maintain the anchor line as per the manufacturer’s recommendations. Keep it clean and store it properly when not in use.

FAQ

• Q: What should I do if I find any defects in the anchor line?
  A: If any defects are found during inspection, do not use the anchor line and contact the manufacturer for guidance on repair or replacement.

• Q: How often should I conduct equipment examinations?
  A: Periodic examinations should be conducted as per regulatory requirements and manufacturer guidelines. Keep a record of all examinations.

• Q: Can the anchor line be used for purposes other than its intended use?
  A: No, always use the anchor line only for its designated purpose to ensure safety and compliance with regulations.

INSTRUCTION MANUAL
WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL AND SPECIFIC.

SPECIFIC INSTRUCTIONS

• These equipments are personal protective equipment (PPE) used for fall protection, shall only be used by a person trained and competent in its safe use and a rescue plan shall be in place to deal with any emergencies that could arise during the work.
• WARNING: Medical conditions could affect the safety of the equipment user in normal and; emergency use. These equipments needs a regular periodic examinations, and that the safety of users depends upon the continued efficiency and durability of the equipment. The periodic examinations are only to be conducted by a competent person for periodic examination and strictly in accordance with the manufacturer’s periodic examination procedures.
• ATTENTION: A pre-use check by the user may not be applicable in the case of certain parts of equipment for emergency use which have been pre-packed or sealed by a competent person. These equipment require the pre-use check and if any components has indication for damage such as corrosion, deformation, seams rupture or others visual defect must be considered inapt to use until the competent person validation. Warning: it is essential for safety to verify the free space required beneath at the workplace before each occasion of use, so that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path.It is essential for safety that equipment is withdrawn from use immediately should: any doubts arise about its condition for safe use or; it has been used to arrest a fall. The recommendation in regard to the frequency of periodic examinations, taking account of such factors as legislation, equipment type, frequency of use, and environmental conditions. The periodic examination frequency shall be at least every 12 months.
• Attention: if a complete system is supplied, that components of any complete system shall not be substituted. Attention with the limitations of the materials; the temperature, the effect of sharp edges, chemical reagents, electrical conductivity, cutting, abrasion, UV degradation, and other climatic conditions may affect its equipment performance. Making any alterations or additions to the equipment without the manufacturer’s prior written consent, and that any repair shall only be carried out in accordance with manufacturer’s procedures. The equipment shall not be used outside its limitations, or for any purpose other than that for which it is intended. Any dangers that may arise by the use of combinations of items of equipment in which the safe function of any one item is affected by or interferes with the safe function of another.
• WARNINGS: It is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall provide instructions for use, for maintenance, for periodic examination and for repair in the language of the country in which the product is to be used. You can find this instruction in our website www.fallsafe-online.com.

HOW TO USE:

Connect the karabiner (EN362) to be held in the major axis positioning and protects the end of the lanyard from wear; clip a locking karabiner (auto locking preferred) through the attachment point (A or 1/2 A+ 1/2 A); make sure that the line is taut; attach the anchor line to a secure anchor point EN795; make sure that the rope grab is at the user shoulders level and not under it. Always check the legibility of the product markings. The equipment becomes wet, either from being in use or when due to cleaning, it shall be allowed to dry naturally, and shall be kept away from direct heat. Verify that this product is compatible with other elements of the system in your application (compatible = good functional interaction). Other types of edges are not allowed and use is prohibited. To be used in horizontal condition, the anchorage point must be located at the same level as the edge, where the risk of fall exists. In order to avoid pendulum effects, the working area must not exceed a 30° angle limit, from each side of the vertical of the anchorage point. IMPORTANT: Despite this test, the following must be observed for all cases during horizontal or sloping use where there is a risk of falling over an edge:

1. If the hazard evaluation performed before commencing work reveals that the fall edge involves particularly “sharp cutting” and / or “burred” edge (e.g. uncovered parapet walls or sharp concrete edge and if devices with fasteners made from webbings are to be used:
2. Corresponding precautions must be taken so that a fall over the edge is precluded, or
3. An edge protection must be mounted before commencing work, or
4. The manufacturer must be contacted
5. The suspension point of the fall arrester must not be below the standing area (e.g. platform, flat roof) of the user. (picture 3)
6. The deflection at the edge (measured between the two flanges of the joints and fastenings) must be at least 90°.
7. The required headroom below the edge is depicted in picture 5.
8. In order to prevent a swinging fall, the work area or side movements from the centre axis must be restricted to max. 1.50m. In other cases, no individual anchorage points, but instead e.g. stopping devices of class C (only if approved for joint use) or D as per EN795 must be used.
9. Note: When using the fall arrester on a stopping device of class C corresponding to EN795 with a horizontally moving guide, the deflection of the stopping device must also be taken into consideration when ascertaining the required clearance height below the user. The information in the instructions for use must be observed for this.
10. Note: In the case of fall over an edge, there is a risk of injury during the catching process as a result of the falling person hitting building parts or structural parts.
11. Special measures for rescuing must be specified and practiced for the event of a fall over the edge.
12. Note: Fall arrest devices identified with picture “A”, “B”, “C” and “D” are not suited for fall impacts over unprotected edges (e.g. retractable Dyneema or Stainless steel rope lanyards).

ADDITIONAL INFORMATION

AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 – Cleaning; AI5 – Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention; AI9 – Right; AI10 – Wrong; AI11 – Check.

MARKING/ LABLES

ML(A) – Serial Number; ML(B) – Product reference; ML(C) – European standard/ Technical specification; ML(D) – Manufacture date; ML(E) – Brand name/ manufacture name; ML(F) – Notified body – which carries out product quality management; ML(G) – Instruction icon; ML(H) – QR Code; ML(I) – Length; ML(J) – Correct orientation incation icon; ML(K) – CE – Complies with the regulation (EU) 2016/ 425 of the European Parliament; ML(9) – Additional information; ML(10) – Manufacture website; ML(11) – Manufacture address; ML(12) – Max load 120kg; ML(13) – Horizontal possibility use icon;

EQUIPMENT RECORD

1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date; 5-Purchase Date; 6-Date of first use; 7-Other relevant information; 8-Date; 9-Reason for entry; 10-Defects,Repair-s,Etc; 11-Name & Signature; 12-Next periodic examination

ALL PERIODIC EXAMINATIONS SHOULD BE RECORDED BY THE COMPETENT PERSON. THIS RECORD SHOULD BE KEPT WITH THE EQUIPMENT DURING THE WHOLE LIFE TIME.

1 – PRODUCT| 2 – REF. NUMBER (SEE THE EQUIPMENT LABEL)| 3 – SERIAL NUMBER (SEE THE EQUIPMENT LABEL)| 4 – MANUFACTURING DATE (SEE THE EQUIPMENT LABEL)
5 – PURCHASE DATE| 6 – DATE OF THE FIRST USE
7 – OTHER RELEVANT INFORMATION
PERIODIC EXAMINATION AND REPAIR HISTORY
8 – DATE| 9 – REASON FOR ENTRY (PERIODIC EXAMINATION OR REPAIR)| 10 – DEFECTS, REPAIRS, ETC.| 11 – NAME & SIGNATURE| 12 – NEXT PERIODIC EXAMINATION (DUE DATE)
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |

NOMENCLATURE/FIELD OF APPLICATION

NFA1 – Steel/ Aluminium Connector; NFA2 – Protective Plastic Sleeve; NFA3 – Rope Grab – Steel/ Aluminium; NFA4 – Polyamide rope; NFA5 – User Anchor Point; NFA6 – Energy Absorber – PES; NFA7 – Energy Absorber – PES; NFA8 – Energy Absorber – PES; NFA9 – Label.

• NOTIFIED BODY – CE1019
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  VVUÚ. a.s, Pikartská 1337/7 – 716 07 Ostrava – Radvanice, Czech Republic

• NOTIFIED BODY – CE0120
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  SGS United Kingdom Ltd, Weston-Super-Mare, BS22 6WA, UK

• NOTIFIED BODY – CE0321
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  SATRA Technology Centre Ltd Wyndham Way Telford Way Kettering, Northamptonshire, NN16 8SD

• ORGANIZATION FOR: (EU) 2016/425 | ISO9001:2015
  SGS FIMKO OY, P.O. Box (Sarkiniementie 3) 00211 Helsinki – Finland NOTIFY BODY: CE 0598

DONNING AND SETUP

DS1- Connect the anchor line into a safe anchorage point (EN795 – >12 kN/ 18 kN to non metallic anchors); DS2 – Complete the connection attaching in the harness EN361 (A or 1/2 + 1/2 A) point; Check the device/ rope use orientation (Fall Safe® recommend to use a front attachment); DS3 – Keep always the anchor line device under the shoulder.
DS(A) – ATTENTION: The user always must be below the anchor point!; DS(B) – No other connecting element must be used between the connector and the harness.

SAFE STEP

According to the Regulation (EU) 2016/425

INSTRUCTION MANUAL

WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL AND SPECIFIC.

SPECIFIC INSTRUCTIONS
Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific equipment instructions.

• ATTENTION!!! If you have any doubt about the product, if you need others language version of the instructions for use, declarations of conformity or any question about the PPE, please contact us: www.fallsafe-online.com.
• WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/ reparations by persons not authorized by FALL SAFE®.

PHYSICAL CONDITION AND TRAINING

• Work at height are potentially dangerous and it must only be used by professionals and experienced persons. Before using the PPE you must be aware of: your mental and physical condition; be trained for the use of the device; do not have any doubt about using the equipment and the field of application.
• WARNING: the equipment shall only be used by a person trained and competent in its safe use.
• WARNING: the consumption of alcohol, medicine or any other type of psychotropic will influence your balance, concentration conditional and must be avoided.

BEFORE USE

• For your safety it is strictly recommended that you always check your device and equipment before, during and after use and that you regularly submit your device and equipment to inspections and controls by competent persons, every 12 months at the latest. These time intervals may change according to frequency and intensity of device and equipment use.

• The FALL SAFE INSPECTOR® allows you to easily record and access information on inspections, inventory and use. It tracks equipment assignments by worker or location and automates the inspection process. There are multiple system options available that allow for easy-access and time-saving information.

• Every time before use, check (visually and tactile) the condition of the equipment components: textile material (straps, ropes, stitching) must not show any signs of abrasion, fraying, burns, chemical or cuts. The metal material (buckles, carabiners, hooks, cable and metal rings) must not show any signs of wear, corrosion, deformation or defects and should operate correctly.

• WARNING: is essential for safety that equipment is withdrawn from use immediately should:

  • Any doubt arise about its condition for safe use or;
  • Is have been used to arrest a fall and not used again until confirmed in writing by a competent person that it is acceptable to do so;

• For you safety read all contained information on this general instructions, as well as the specific instructions accompanying the device and make sure that you understand them; ensure the equipment conditioning and all recommendation of security; ensure that the components are compatible with each other and be sure if are fulfilled with the rules, regulations and directives; ensure an emergency plan, check the work safety conditioning and confirm all system are assembled correctly without interfering with each other.

• WARNING: use of combinations of items of equipment in which the safe function on any one item is affected by or interferes with the safe function of another.

• WARNING: that a rescue plan shall be in place to deal with any emergencies that could arise during the work.

• WARNING: Remind to check the limitation and the devices compatibility. Remember that the ropes have different particularities and can be changed according the weather conditioning. The manufacture declines any responsibility for accidents, injuries or death due to improper and incorrect use by the user, all other usage procedures must be considered forbidden. The equipment shall not be used outside its limitations, or for any purpose other than that for which it is intended.

• WARNING: it is essential for safety to verify the free space required beneath the user at the workplace before each occasion of use, so that in the case of a fall, there will be no collision with the ground or other obstacle in the fall path.

• As the name suggests, the PPE is for personal use. In exceptional case using by a second user, carry out a check of the equipment before and after usage and if possible take note of the relevant date.

• WARNING: never use a PPE without knowing the provenance, or neither if the inspection records are not updated as it is issued.
  All the materials and treatments used are antiallergenic; they should not cause skin irritations or sensitivity. The connectors are made of steel, zinc plated; light alloy, polished or anodized: stainless steel, polished.

• WARNING: during the use avoid the following hazards that may affect the performance of the equipment: extremes of temperature, trailing or looping of lanyards or lifelines over sharp edges, chemical reagents, electrical conductivity, cutting, abrasion, climatic exposure and pendulum falls.

MARKING

• WARNING: Never remove or damage de labels and marking; after use check if they are legible. The following information is etched on the device: CE marking; (Number of the production process controlling body); Name of the manufacturer or of the person responsible for the product introduction on the market; standard (number and year of the standard; the logo that warns the user to carefully read the user instructions attached to the product; production lot number; year of production; maximum load applicable in kN, the strength indicated is the lowest value guaranteed by the producer. The marking on the device are indicated in different places depending on the dimension. See more detailed in “Specific Instructions”.
• WARNING: Check the markings are legible even after use.
• WARNING: it is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall provide instructions for use, for maintenance, for periodic examination and for repair in the language of the country in which the product is to be used.

LIFE TIME

• It is rather difficult to establish the length of the device’s life, as it can be adversely affected by several negative factors such as intensely frequent or improper use; the conditions the device is required to work in (humid, freezing and icy conditions); wear; corrosion; serious stress with or without relative deformation; exposure to heat sources; improper storage; device age; exposure to chemical agents… (plus any further reason, not merely limited to all the foregoing reasons).
• Taking the adequate care of your device (please consult the “Maintenance”) will have a considerable influence on and will definitely increase device durability and long life. By the way of example, the following can be considered as a rule to determine standard potential durability of devices, tools and equipment: ten years for fall protection harness, fall protection vests/jacket-s/ coveralls, accessories (lanyards, foot loop, suspension trauma and relief strap) anchor lines, anchor straps, ropes, carrying bags, fall arrest webbing blocks and sharp edge tested; eight years for equipment conditioned to extreme environments (harness, lanyards, vests, jackets and coveralls); undefined for connectors, descenders, rope clamps, rope grabs, pulleys, anchor points; especially 10 years (5 in stock – 5 in use) for gloves and helmet .
• It is nevertheless recommended that you replace your devices, tools and equipment at least every 10 years, considering that in the meantime new techniques or regulations may have become applicable and your equipment may no longer be compliant and/or compatible with one another. WARNING: The lifetime of an equipment can be limited in case of severe falls, extreme temperatures, contact with harmful chemicals, sharp edges and the absence of markings or labels.

ELIMINATION/ DISPOSAL CONSIDERATIONS

• You should dispose of the equipment if: the lifetime has been exceed; if you suspect that the equipment is not safe; if it is obsolete (incompatible with modern equipment or that do not conform to the standards updates); if it has been in a fall event (see the fall arrest indicator was violated); if it is over than 10 years.
• The materials used in the equipment production may cause environmental impacts. For this purpose it is recommended that the equipment are disposed of in accordance with the laws in force in the country where the disposal is taking place.
• WARNING: The equipment which is not in operable condition or used in a fall event must be destroyed immediately.

REPARATION
ATTENTION!!! Any modification on the product void the guarantee and can compromise the user´s safety. The possibility of re-using the device must be authorized exclusively by the producer with a prior written consent that reserves the right to carry out appropriated examina-tions and testing. Only the manufacture or authorized staff can make the repairs and tampering.

MAINTENANCE, CLEANING AND INSPECTION

• Check before, after and during use that the equipment works properly. If you need wash the components use clean water with a small amount of neutral soap to remove persistent dirt or if the purpose is disinfect dissolve a disinfectant which contains quaternary ammonium salts in warm water (max. 20ºC), soak the equipment in this solution for one hour.
• Rinse with potable water and leave them to dry out in the open air protected from sunlight.
• WARNING: when the equipment becomes wet, either from in use or when due to cleaning, I shall be allowed t dry naturally, and shall be kept away from direct heat.
• If you need to lubricate the metal components you must use only silicone based oil spray.
• WARNING: Remove the excess oil and check that if the lubrication don’t interferes the interaction between the device, others components of the system and the user’s.
• For your safety it is therefore highly recommended that submit your device and equipment to inspections and controls by competent persons, every 12 months at the latest. These time intervals may change according to frequency and intensity of device and equipment use. If you ever have even the smallest doubt as to the condition of the device, please contact us: www.fall-safe-online.com. The FALL SAFE INSPECTOR® allows you to easily record and access information on inspections, inventory and use. It tracks equipment assignments by worker or location and automates the inspection process. There are multiple system options available that allow for easy-access and time-saving information.
• WARNING: for regular periodic examination, and that the safety of users depends upon the continued efficiently and durability of the equipment.
• WARNNG: periodic examination are only to be conducted by a person competent for periodic examination and strictly in accordance with the manufacture´s periodic examination procedures.

STORAGE/ TRANSPORT
Remove the item from its container and store it in a cool, dry, well-aired place. There must not be any corrosive, solvent substances or heat sources (max. 80°C/ 176°F) in the storage place. The device must not come in contact with other sharp objects which can damage it. Never store the equipment before having thoroughly dried it and avoid storing it in places with a high saline concentration. Except for the above-mentioned indications, there are no special precautions to be used during the transport. Avoid leaving your equipment in a car or in a closed placed exposed to the sunlight.

GUARANTEE

This product is provided with a three year warranty against any manufacturing defect, or defects in the materials it is composed of. The warranty does not cover standard item wear, device alterations, improper storage, damages due to improper use of the device, negligence, improper maintenance, etc., and any further reason not only limited to the aforesaid.

ADDITIONAL INFORMATION
AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 – Cleaning; AI5 – Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention; AI9 – Right; AI10 – Wrong; AI11 – Check.

MARKING/ LABLES
ML(A) – Reference number; ML(B) – Manufacture date; ML(C) – Brand name; ML(D) – Instructions; ML(E) – QR code;

EQUIPMENT RECORD
1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date; 5-Purchase Date; 6-Date of first use; 7-Other relevant information; 8-Date; 9-Reason for entry; 10-Defects,Repair-s,Etc; 11-Name & Signature; 12-Next periodic examination

EQUIPMENT RECORD

ALL PERIODIC EXAMINATIONS SHOULD BE RECORDED BY THE COMPETENT PERSON. THIS RECORD SHOULD BE KEPT WITH THE EQUIPMENT DURING THE WHOLE LIFE TIME.

1 – PRODUCT| 2 – REF. NUMBER (SEE THE EQUIPMENT LABEL)| 3 – SERIAL NUMBER (SEE THE EQUIPMENT LABEL)| 4 – MANUFACTURING DATE (SEE THE EQUIPMENT LABEL)
5 – PURCHASE DATE| 6 – DATE OF THE FIRST USE
7 – OTHER RELEVANT INFORMATION
PERIODIC EXAMINATION AND REPAIR HISTORY
8 – DATE| 9 – REASON FOR ENTRY (PERIODIC EXAMINATION OR REPAIR)| 10 – DEFECTS, REPAIRS, ETC.| 11 – NAME & SIGNATURE| 12 – NEXT PERIODIC EXAMINATION (DUE DATE)
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |

NOMENCLATURE/FIELD OF APPLICATION
NFA1 – Webbing 25mm; NFA2 – Dyneema Rope; NFA3 – Storage Bag; NFA4 – Adjust Buckle; NFA5 – Attachment Point; NFA6 – Webbing 44mm.

DONNING AND SETUP
DS(A) – BEFORE USE THE SAFE STEP MUST BE CONNECTED WITH A KARABINER OR INTERLACED IN WORKING POSITIONING D-RIND OR VENTRAL D-RING; DS(B) – OPEN THE SAFE STEP BAG; DS(C) – CONNECT THE BUCKLE IN THE WEBBING LOOP ACCOR-DING YOUR LEG SIZE; DS(D) – CONNECT THE BUCKLE IN THE WEBBING; DS(E) – PUSH THE WEBBING TO BE TAUT; DS(F) – USE THE BUCKLE THE ADJUST THE WEBBING; DS(G) – ANCHOR THE SAFESTEP TO A SAFE ANCHOR POINT; DS(H) – ANCHOR THE SAFESTEP TO A SAFE ANCHOR POINT AND CONNECT THE KARABINERS IN THE HOLES; DS(I) – MAKE THE ADJUSTMENT PASSING THE ROPES IN THE HOLES; DS(J) – THE SAFESTEP IT´S READY TO USE

ANCHOR DEVICE

According to the Regulation (EU) 2016/425

• Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific equipment instructions.
• ATTENTION!!! If you have any doubt about the product, if you need others language version of the instructions for use, declarations of conformity or any question about the PPE, please contact us: www.fallsafe-online.com.
• WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/ reparations by persons not authorized by FALL SAFE®. This equipment it (EN795:2012 Class B) was designed as a temporary transportable anchor point for work at height purposes. Do not use for hauling equipment. The sling will transmit any force applied directly to the structures in the directions in which it is applied. The sling will attempt to align with applied force and it may slide if the load is not perpendicular to the structure. Verify that this product is compatible with the other elements of the system in your application and use only connectors EN362. Choking around the anchor structure reduces the strength of the sling and can damage it. Use always the correct length to avoid the angle where the ends of the sling meet the connector is less than 90°. This equipment must not be pushed beyond its limits or be used for any purpose other than that for which it is designed.
• WARNING: Avoid all contact with sharp edges or abrasive surfaces. This anchor device is for of one person only. When the anchor device is used as part of a fall arrest system, the user must be equipped with a means of limiting the impact force, exerted on the user when the fall is arrested to a maximum value of 6 kN. The anchorage point should be located above the user if possible and must satisfy the requirements specified in EN795 (minimum strength of 12 kN).
• Attention: it is recommended the anchor device is marked with the date of the next or last inspection.

ADDITIONAL INFORMATION
AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 – Cleaning; AI5 – Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention; AI9 – Right; AI10 – Wrong; AI11 -Check.

MARKING/ LABLES
ML(A) – Serial number; ML(B) – Reference number; ML(C) – Standard; ML(D) – Manufacture date; ML(E) – Brand name; ML(F) – Notified body which carries out product quality management; ML(G) – Instruction; ML(H) – QR code.

EQUIPMENT RECORD
1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date; 5-Purchase Date; 6-Date of first use; 7-Other relevant information; 8-Date; 9-Reason for entry; 10-Defects,Repair-s,Etc; 11-Name & Signature; 12-Next periodic examination

ALL PERIODIC EXAMINATIONS SHOULD BE RECORDED BY THE COMPETENT PERSON. THIS RECORD SHOULD BE KEPT WITH THE EQUIPMENT DURING THE WHOLE LIFE TIME.

1 – PRODUCT| 2 – REF. NUMBER (SEE THE EQUIPMENT LABEL)| 3 – SERIAL NUMBER (SEE THE EQUIPMENT LABEL)| 4 – MANUFACTURING DATE (SEE THE EQUIPMENT LABEL)
5 – PURCHASE DATE| 6 – DATE OF THE FIRST USE
7 – OTHER RELEVANT INFORMATION
PERIODIC EXAMINATION AND REPAIR HISTORY
8 – DATE| 9 – REASON FOR ENTRY (PERIODIC EXAMINATION OR REPAIR)| 10 – DEFECTS, REPAIRS, ETC.| 11 – NAME & SIGNATURE| 12 – NEXT PERIODIC EXAMINATION (DUE DATE)
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |

NOMENCLATURE/FIELD OF APPLICATION
NFA1 – Polyester Webbing – 25mm; NFA2 – Heavy-duty Polyester Webbing – 44 mm; NFA3 – Galvanized Steel Wire; NFA4 – Dyneema®; NFA5 – Steel Conector – EN362; NFA6 – Aluminium Loop; NFA7 – D-Ring Steel Connector

• NOTIFIED BODY CE0120
  LISTED ORGANISATION FOR CE TYPE APPROVAL:
  SGS United Kingdom Ltd, Weston-Super-Mare, BS22 6WA, UK NOTIFIED BODY: CE0120

• NOTIFIED BODY CE1019
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  VVUÚ. a.s, Pikartská 1337/7 – 716 07 Ostrava – Radvanice, Czech Republic NOTIFIED BODY: CE1019

• LISTED ORGANIZATION FOR: (EU) 2016/425 | ISO 9001:2015
  SGS FIMOKO OY, P.O. Box 30 (Särkiniementie 3) 00211 Helsinki – Finland NOTIFIED BODY: CE 0598

DONNING AND SETUP

BASIC HARNESS

According to the Regulation (EU) 2016/425

WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL AND SPECIFIC.

SPECIFIC INSTRUCTIONS

• Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific equipment instructions.
• ATTENTION!!! If you have any doubt about the product, if you need others language version of the instructions for use, declarations of conformity or any question about the PPE, please contact us: www.fallsafe-online.com.
• WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/ reparations by persons not authorized by FALL SAFE®. The full body harness is the only acceptable body retaining device that can be used in a fall arrest system.
• The fall arrest harness should only be used as personal fall arrest system in accordance with EN363, as fall arrest system, restraint system, works positioning system, rescue system with the following tested and approved components: height safety devices in accordance with EN360; travelling fall arrest devices on moveable guides in accordance with EN353-2; lanyards with strap fall brakes in accordance with EN354/EN1496; lanyard in accordance with EN354; Karabiners in accordance with EN362. The anchorage point on which the protective equipment is fastened should be located above the user if possible and must satisfy the requirements specified in EN795 (minimum strength of 12kN).
• The dorsal and chest D-rings (“A” points) must be connected to a fall arrest system that meets current standards. Use only “A” attachment point for fall arrest system connection, for example a mobile fall arrest, an energy absorber. In a fall event, the fall arrest attachment pint elongates approximately 0.5 m. This elongation must be taken into account for the clearance calculation. When is available, the ventral and the side attachment points on the work belt are designed to either hold the user in work position, or to restrain the user from entering a hazard zone.
• ATTENTION: The side attachment point is not designed for fall arrest usage. Always use the two side attachment points together, by linking them with a work positioning lanyard, in order to be comfortable supported by the comfort pad of the work belt.
• WARNING: Be sure the webbing is inserted in the correct position.
• ATTENTION: Prolonged suspension in case of a fall can cause suspension trauma that may lead to serious injuries or dead! Plese avoid suspension trauma! The rescue harness is intended to be worn during normal working activities and that you should carry out a suspension test in a safe place before using the rescue harness for the first time, to ensure that it is the correct size, has sufficient adjustment and is of an acceptable comfort level for the intended use.
• WARNING: The rescue harness, FS236 – maximum load 100 kg, shall not to be used as the body holding device in a fall arrest system.
• WARNING: the waist belt is not suitable for fall arrest purposes and that a waist belt should not be used if there is a foreseeable risk of the user becoming suspended or being exposed to unintended tension by waist belt.
• WARNING: using a work positioning system it is essential to consider the need of using a back-up, e.g. a fall arrest system.
• WARNING: for work positioning it is essential for safety use an anchor point positioned at above waist level.
• ATTENTION: The waist belt is approved for a user, including tools and equipment, with a weight of up to 150 kg. For adjust the work positioning lanyards you must attach the connector of the end of the lanyards to the positioning side D-ring of your harness. Pass the rope through a reliable anchor point EN795. Attach the connector on the other lanyard end to the positioning D-ring. You can attach the positioning lanyard to a ring anchor point.
• WARNINIG: The rope must be taut to prevent accidents. Never connect the lanyards directly to a structure (cable, bar, etc.) having a slope greater than 15° because the fall length may then exceed 0.6m.
• WARNING: Karabiners must always be used with the gate closed and locked. Systematically verify that the gate is securely locked by pressing it with your hand. Avoid contact with sharp or abrasive surfaces and objects. According to EN358, please note it is essential to regularly check fastening and adjustment elements during use.
• ATTENTION: Waist belt is approved for a user including tools and equipment with a weight of up to 150 kg. In accordance with EN813 it is essential to check fastening and adjustment elements regularly, as well as essential to check the sit harness regularly for any damage. ATTENTION: a sit harness is not suitable for fall arrest purposes. Attachment points of the sit harness (figure 1) can be used for restriction or work positioning. For work positioning (1), attach the work positioning lanyard connector to the work positioning ring on the sit harness, pass the rope through a safe spot; make sure that the lanyard is taut and attach to the other side ring. For restriction (2), Attach the connector on the other lanyard extremity to the positioning D-ring and attach the positioning lanyard to a fixed anchor point.

ADDITIONAL INFORMATION
AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 – Cleaning; AI5 – Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention; AI9 – Right; AI10 – Wrong; AI11 – Check.

MARKING/ LABLES
ML(A) – Serial number; ML(B) – Reference number; ML(C) – Standard; ML(D) – Manufacture date; ML(E) – Brand name; ML(F) – Notified body which carries out product quality management; ML(G) – Instruction; ML(H) – QR code; ML(I) – CE Marking – complies with regulation (EU) 2016/425; ML(J)- Maximum load; ML(K) – Size; ML(L – Fit icons.

EQUIPMENT RECORD
1-Product 2-Reference Number 3-Serial Number 4-Manufacturing Date 5-Purchase Date 6-Date of first use 7-Other relevant information 8-Date 9-Reason for entry 10-Defects,Repairs,Etc 11-Name & Signature 12-Next periodic examination

NOMENCLATURE/FIELD OF APPLICATION
NFA1- Steel D-ring or aluminium D-ring – Dorsal Attachment (A); NFA2- Steel D-ring or aluminium D-ring or Webbing Loop – Chest Attachment (A); NFA3- Steel D-ring or aluminium D-ring or Webbing Loop – Ventral Attchment; NFA4- Steel D-ring or aluminium D-ring – Work Positioning Attachment; NFA5- Lanyard Keepers; NFA6- Steel quick release buckle or aluminium quick release buckle; NFA7- Steel – 3 Bar Buckles; NFA8- Tool Holder; NFA9- FALL SAFE INSPECTOR® Ready, NFA10- Webbing Keepers; NFA11- Fall Arrest Indicator; NFA12- Karabiner (EN362). LISTED ORGANIZATION FOR: (EU) 2016/425 | ISO 9001:2015 SGS FIMOKO OY, P.O. Box 30 (Särkiniementie 3) 00211 Helsinki – Finland NOTIFIED BODY: CE 0598

• NOTIFIED BODY – CE1019
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  VVUÚ. a.s, Pikartská 1337/7 – 716 07 Ostrava – Radvanice, Czech Republic

• NOTIFIED BODY – CE0120
  LISTED ORGANISATION FOR EU TYPE APPROVAL:
  SGS United Kingdom Ltd, Weston-Super-Mare, BS22 6WA, UK

DONNING AND SETUP
DS1 – Check you equipment and open all buckles; DS2 – Put on the shoulder harness like you would put on the vest; DS3 – Close the chest buckle; DS4.1 | DS4.2 – Pass the strap between your legs and close the buckle. After closing make sure it´s tight; DS5.1 | DS5.2 – Ready to use; DS6 – Check your harness and open all buckles; DS7 – Put on the shoulder harness like you would put on the vest; DS8 – Close the chest buckle; DS9 – Close the ventral buckle; DS10 – Pass the strap between your legs and close the buckle; DS11 – After closing all buckles make sure that all of them are tight; DS12 – Ready to use DS13 – Check your harness; DS14 – Put on the harness in the waist area and legs straps area; DS15 – Close the legs insert buckle (click!) and adjust it; DS16 – Tighten/ adjust the bar buckle in the waist area and in the legs buckles; DS17 – Put on the shoulder harness like you would put on the vest. Closed the insert buckle and tight it; DS18 – Insert the carabiner (EN362) on the ventral loop to unify the two parts and be sure that it is properly closed; Tight the two side chest bar buckles; DS19 – Finally tight the strap of the rear bar buckle; DS20 – If you need to separate the parts follow the steps as the picture shows.

CONNECTORS

According to the Regulation (EU) 2016/425

INSTRUCTION MANUAL
WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL AND SPECIFIC.

SPECIFIC INSTRUCTIONS

• Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific equipment instructions.
• ATTENTION!!! If you have any doubt about the product, if you need others language version of the instructions for use, declarations of conformity or any question about the PPE, please contact us: www.fallsafe-online.com.
• WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/ reparations by persons not authorized by FALL SAFE®. These instructions contain all the necessary information for the correct and safe use of the connectors (EN362) in the fields of activity. The connectors covered by these instructions are personal protection devices designed to be integrated in fall arrest personal protection systems such as harnesses, lanyards, and anchor devices. The connectors are a vital transmission component of the mechanical resistance between a proper anchor point and the user who accidentally fall. A malfunction due to improper use of the equipment is dangerous for the physical health of the user. The connector must be used as follows: closed – with the closing system locked – without any constrictions or other pressures on the outer side of the connector. Only some of these incorrect uses are included in these instructions and these are indicated with a cross over the illustrations. Only the ways indicated as “OK” are allowed.
• When a connector is inserted in any fall arrest system, in order to regulate the other components correctly and not compromise the efficiency of the system, you must take into account the length of the connector. The closing system must function perfectly and to help assure this the connector must be lubricated. These devices have been designed for use in weather conditions normally tolerated by man.

TYPES OF CONNECTORS FOR PERSONAL PROTECTION (EN 362:2004)

• Class A – Anchor connectors: component designed to be linked directly to a specific type of anchor;
• Class B – Basic connectors: intended to be used as a component;
• Class M – Multi-use connectors: component which may be loaded in the major and minor axis;
• Class T – Termination connectors: element of a sub-system in which the loading acts on a predetermined direction;
• Class Q – Screw gate connectors: intended to be used only for enduring or permanent connections. The class identification is marked on the device. Refer to table to identify the rank and the maximum gate opening (“a” in mm) of your connector.
• Use only anchor’s complying with the EN 795 with a minimum breaking strength of 12 kN. While using the connector and other personal protective devices, the user must always remain below the anchor point. The position and the height of the anchor point from the ground must be calculated in the view of a possible fall, taking into account the length of the rope, any dangerous “obstacles” and the possibility of a “swinging” effect. The work must be carried out in such way as to minimize both the potential fall and potential fall distance.
• WARNING: The connectors equipped with a manual-locking gate (screw gate) are to be used only when the opening and closing operations are not frequent.
• When using these connectors the screw must be completely closed; for connectors class Q it must be verify that the threads of the screw are not visible. Avoid loading the connector across its gate. Verify that a technical identification and equipment record in conformity with standard EN 365:2004 is provided with the product. This recorder must be filled in and kept updated by the user. If the recorder is missing, do not use the device. ALWAYS CHECK before, after and during use that the connector works properly. ALWAYS REPLACE the connector after a fall even if no defect or damage are visible; the initial resistance of the connector could be seriously reduced. The possibility of re-using the device must be authorized exclusively by the producer with a prior written consent that reserves the right to carry out appropriated examinations and testing. Any repair should only be carried out in accordance with producer’s procedures.
• WARNING: replace the connector that shows signs of wear and corrosion.
• WARNING: replace the connector if the opening and/or closing/locking are difficult. Clean the connectors with water and dry it with a non-abrasive cloth. When using CATCH-FREE System connectors, pay particular attention to the slot on the lever: it has to be dirt-free (soil, mud, gravel, etc. – list not exhaustive). In the case of use on icy conditions make sure that the slot on the lever is not obstructed by snow or ice.
• FS830 – Particularity: The hook must always be used with the gate locked. Unlock and opening the gate single-handedly. To open the gate, lift the ring and press in on the opposite gate direction. To locking the mechanism on the hook engages automatically when the hook´s gate is released. Check if the gate it´s closed and locked properly without any obstruct.

ADDITIONAL INFORMATION
AI1 – Acceptable Temperature; AI2 – Storage; AI3 – Annual Inspection; AI4 – Cleaning; AI5 – Drying; AI6 – Hazards; AI7 – Risk of death; AI8 – Attention; AI9 – Right; AI10 – Wrong; AI11 – Check.

MARKING/ LABELS
ML(A) – Brand name; ML(B) – Batch number / Manufacture Date; ML(C) – Standard; ML(D) – Instruction; ML(E) – Strength; ML(F) – Model; ML(G) – Notify body which carries out product quality management; ML(H) – Max. users; ML(I) – Electronic address; ML(J) – Opening; ML(K) – CE – complies with regulation (EU) 2016/426 of the European Parliament

EQUIPMENT RECORD
1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date; 5-Purchase Date; 6-Date of first use; 7-Other relevant information; 8-Date; 9-Reason for entry; 10-Defects,Repair-s,Etc; 11-Name & Signature; 12-Next periodic examination

ALL PERIODIC EXAMINATIONS SHOULD BE RECORDED BY THE COMPETENT PERSON. THIS RECORD SHOULD BE KEPT WITH THE EQUIPMENT DURING THE WHOLE LIFE TIME.

1 – PRODUCT| 2 – REF. NUMBER (SEE THE EQUIPMENT LABEL)| 3 – SERIAL NUMBER (SEE THE EQUIPMENT LABEL)| 4 – MANUFACTURING DATE (SEE THE EQUIPMENT LABEL)
5 – PURCHASE DATE| 6 – DATE OF THE FIRST USE
7 – OTHER RELEVANT INFORMATION
PERIODIC EXAMINATION AND REPAIR HISTORY
8 – DATE| 9 – REASON FOR ENTRY (PERIODIC EXAMINATION OR REPAIR)| 10 – DEFECTS, REPAIRS, ETC.| 11 – NAME & SIGNATURE| 12 – NEXT PERIODIC EXAMINATION (DUE DATE)
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |

NFA – NOMENCLATURE / FIELD OF APPLICATION

DS – DONNING AND SETUP
DS1 – CARABINERS; DS2 – HOOKS; DS3 – CONNECTORS; DS4 – LINKS..

GENERAL INSTRUCTIONS

• Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific instructions.
• ATTENTION!!! If you have any doubt about the product, if you need others language versions of the instructions for use, declarations of conformity or have any question about the PPE, please contact us: www.fallsafe-online.com.
• WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/reparations by persons not authorized by FALL SAFE®.

PHYSICAL CONDITION AND TRAINING:

• Work at height is potentially dangerous and it must only be performed by professionals and experienced persons. Before using the PPE you must be aware of: your mental and physical condition; be trained for the use of the device; do not have any doubt about using the equipment and the field of application.
• WARNING: the equipment shall only be used by a person trained and competent in its safe use.
• WARNING: the consumption of alcohol, medicine or any other type of psychotropic will influence your balance, concentration conditional and must be avoided.

BEFORE USE:

• For your safety it is strictly recommended that you always check your device and equipment before, during and after use and that you regularly submit your device and equipment to inspections and controls by competent persons, every 12 months at least. These time intervals may change according to frequency and intensity of device and equipment use. The FALL SAFE INSPECTOR® allows you to easily record and access information on inspections, inventory and use. It tracks equipment assignments by worker or location and automates the inspection process. There are multiple system options available that allow for easy-access and time-saving information.
• Every time before use, check (visually and tactile) the condition of the equipment components: textile material (straps, ropes, stitching) must not show any signs of abrasion, fraying, burns, chemical or cuts. The metal material (buckles, karabiners, hooks, cable and metal rings) must not show any signs of wear, corrosion, deformation or defects and should operate correctly.
• WARNING: it is essential for safety that equipment is withdrawn from use immediately if:
  • Any doubt arise about its condition for safe use or;
  • It have been used to arrest a fall. It cannot be used again until confirmed in writing by a competent person that it is acceptable to do so;
• For your safety read all contained information on this general instructions, as well as the specific instructions accompanying the device and make sure that you understand them; ensure the equipment conditions and all recommendation of security; ensure that the components are compatible with each other and be sure if are fulfilled with the rules, regulations and directives; ensure an emergency plan, check the work safety conditioning and confirm all system are assembled correctly without interfering with each other.
• WARNING: use of combinations of items of equipment in which the safe function on any one item is affected by or interferes with the safe function of another. WARNING: a rescue plan shall be in place to deal with any emergencies that could arise during the work.
• WARNING: Remind to check the limitation and the devices compatibility. Remember that the ropes have different particularities and can be changed according to the weather conditions. The manufacture declines any responsibility for accidents, injuries or death due to improper and incorrect use by the user, all other usage procedures must be considered forbidden. The equipment shall not be used outside its limitations, or for any purpose other than that for which it is intended. WARNING: it is essential for safety to verify the free space required beneath the user at the workplace before each occasion of use, so that in the case of a fall, there will be no collision with the ground or other obstacle in the fall path.
• As the name suggests, the PPE is for personal use. In exceptional case using by a second user, carry out a check of the equipment before and after usage and if possible take note of the relevant information.
• WARNING: never use a PPE without knowing the provenance, or neither if the inspection records are not updated as it is issued.
• All the materials and treatments used are antiallergenic; they should not cause skin irritations or sensitivity. The connectors are made of steel, zinc plated; light alloy, polished or anodized: stainless steel, polished.
• WARNING: during the use avoid the following hazards that may affect the performance of the equipment: extremes of temperature, trailing or looping of lanyards or lifelines over sharp edges, chemical reagents, electrical conductivity, cutting, abrasion, climatic exposure and pendulum falls.

MARKING

• WARNING: Never remove or damage the labels and marking; after use check if they are legible.
  The following information is etched on the device: CE marking; (Number of the production process controlling body); Name of the manufacturer or of the person responsible for the product introduction on the market; standard (number and year of the standard; the logo that warns the user to carefully read the user instructions attached to the product; production lot number; year of production; maximum load applicable in kN, the strength indicated is the lowest value guaranteed by the producer. The marking on the device are indicated in different places depending on the dimension. See more detailed in “Specific Instructions”.

• WARNING: Check the markings are legible even after use.

• WARNING: it is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall provide instructions for use, for maintenance, for periodic examination and for repair in the language of the country in which the product is to be used.

LIFE TIME

• It is rather difficult to establish the length of the device’s life, as it can be adversely affected by several negative factors such as intense, frequent or improper use; the conditions the device is required to work in (humid, freezing and icy conditions); wear; corrosion; serious stress with or without relative deformation; exposure to heat sources; improper storage; device age; exposure to chemical agents… (plus any further reason, not merely limited to all the foregoing reasons). Taking the adequate care of your device (please consult the “Maintenance”) will have a considerable influence on and will definitely increase device durability and long life. By the way of example, the following can be considered as a rule to determine standard potential durability of devices, tools and equipment: ten years for fall protection harness, fall protection vests/jackets/ coveralls, accessories (lanyards, foot loop, suspension trauma and relief strap) anchor lines, anchor straps, ropes, carrying bags, fall arrest webbing blocks and sharp edge tested; eight years for equipment conditioned to extreme environments (harness, lanyards, vests, jackets and coveralls); undefined for connectors, descenders, rope clamps, rope grabs, pulleys, anchor points; especially 10 years (5 in stock – 5 in use) for gloves and helmet . It is nevertheless recommended that you replace your devices, tools and equipment at least every 10 years, considering that in the meantime new techniques or regulations may have become applicable and the equipment may no longer be compliant and/or compatible.
• WARNING: The lifetime of an equipment can be limited in case of severe falls, extreme temperatures, contact with harmful chemicals, sharp edges and the absence of markings or labels.

ELIMINATION/ DISPOSAL CONSIDERATIONS

• You should dispose of the equipment if: the lifetime has been exceed; if you suspect that the equipment is not safe; if it is obsolete (incompatible with modern equipment or that do not conform to the standards updates); if it has been in a fall event (see the fall arrest indicator was violated); if it is over than 10 years. The materials used in the equipment production may cause environmental impacts. For this purpose it is recommended that the equipment are disposed of in accordance with the laws in force in the country where the disposal is taking place.
• WARNING: The equipment which is not in operable condition or used in a fall event must be destroyed immediately.

REPARATION
ATTENTION!!! Any modification on the product void the guarantee and can compromise the user’s safety. The possibility of re-using the device must be authorized exclusively by the producer with a prior written consent that reserves the right to carry out appropriated examinations and testing. Only the manufacture or authorized staff can make the repairs and tampering.

MAINTENANCE, CLEANING AND INSPECTION

• Check before, after and during use that the equipment works properly. If you need wash the components use clean water with a small amount of neutral soap to remove persistent dirt or if the purpose is disinfect dissolve a disinfectant which contains quaternary ammonium salts in warm water (max. 20ºC), soak the equipment in this solution for one hour. Rinse with potable water and leave them to dry out in the open air protected from sunlight.
• WARNING: when the equipment becomes wet, either from in use or when due to cleaning, I shall be allowed t dry naturally, and shall be kept away from direct heat. If you need to lubricate the metal components you must use only silicone based oil spray.
• WARNING: Remove the excess oil and check that if the lubrication don’t interferes the interaction between the device, others components of the system and the user’s. Accordingly to the EN 365:2004 the PPE periodical examination should be carried out at least every 12 months by the manufacturer or a competent person specifically authorized by the manufacturer. The frequency of inspection must vary depending on the intensity of usage, in order to ensure the durability of the product and safety of the user. The inspection reports must be kept by the PPE owner. The result of the inspection must always accompany the product. If the report is missing or illegible, do not use the device. In case of doubt, the product should always be rejected. The FALL SAFE INSPECTOR® allows you to easily record and access information on inspections, inventory and use. It tracks equipment assignments by worker or location and automates the inspection process. There are multiple system options available that allow for easy-access and time-saving information.
• WARNING: for regular periodic examination, and that the safety of users depends upon the continued efficiently and durability of the equipment.
• WARNNG: periodic examination are only to be conducted by a person competent for periodic examination and strictly in accordance with the manufacture´s periodic examination procedures.

STORAGE/ TRANSPORT
Remove the item from its container and store it in a cool, dry, well-aired place. There must not be any corrosive, solvent substances or heat sources (max. 80°C/ 176°F) in the storage place. The device must not come in contact with other sharp objects which can damage it. Never store the equipment before having thoroughly dried it and avoid storing it in places with a high saline concentration. Except for the above-mentioned indications, there are no special precautions to be used during the transport. Avoid leaving your equipment in a car or in a closed placed exposed to the sunlight.

GUARANTEE
The products are guaranteed for 12 months against any defects in material or manufacture. To analyses defects in materials and manufacture contact our after-sales service to get the address to which should return the defective product in your country. Notes: Exclusions from the guarantee – incorrect wear, oxidation, leaking batteries in headlamps, modification/ alteration, poor storage, poor maintenance, damage due to accident or negligence, damage due use of product for which it is not designed. The manufacture guarantee also does not apply if the serial number is no longer legible, any label has been removed from the product, if has been written on with a marker, covered by stickers or using others tools for this purpose and if the annual inspection are not been realized.

FALL SAFE ONLINE, LDA
Zona Industrial da Varziela, Rua B – Lote 54 4480-620 Vila do Conde
Portugal, EU

www.fallsafe-online.com
E-mail: support@fallsafe-online.com

References

• safe-online.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>