QIDI TECH X-PLUS3 3D Printer User Guide
- June 10, 2024
- QIDI TECH
Table of Contents
QIDI TECH X-PLUS3 3D Printer
Product Information
The device complies with part 15 of the FCC Rules, which means that it meets the standards set by the Federal Communications Commission for electronic devices. The device is designed to operate without causing harmful interference to other electronic devices. It is also designed to accept any interference that it receives, including interference that may cause undesired operation. Any changes or modifications made to the device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The equipment also complies with FCC radiation exposure limits set for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body. This is to ensure that you are not exposed to excessive radiation levels when using the device.
Product Usage Instructions
To use the device, follow these instructions:
- Ensure that the device is installed and operated in a location where it is at least 20cm away from your body.
- Do not make any changes or modifications to the device that are not expressly approved by the manufacturer.
- If you experience any interference when using the device, try
moving it to a different location or adjusting its position. If you have any questions or concerns about the device or its operation, refer to the user manual or contact the manufacturer for
assistance.
Usage Notice
- Do not place the machine in flammable and explosive materials or near high heat sources, please place the machine in a ventilated, cool and dust-free environment.
- The X-axis carbon fiber rod on the machine cannot be replaced,so please take care to protect it from scratching the carbon fiber rod and affecting printing.
- Ensure the machine is powered off(unplug power cord) before performing maintenance or modifications.
- Before connecting the power,please follow the power setup instructions to ensure that the voltage is correct.
- Never reach inside QIDI printer while they are in operation.
- Children should be under constant supervision when using QIDI products.
- The printer contains high-speed moving parts, so be careful of hands pinching.
- There is a potential risk of burns: the print heads of the QIDI printers can reach temperatures above 300 ° C, while the hot bed can reach temperatures above 100 ° C.Do not touch either of these parts with your bare hands.
- Do not place the printer in a vibrating or other unstable environment. Otherwise the shaking of the machine will affect the printing quality.
- After printing, use the residual temperature of the print head to clean the filament around the nozzle with the dedicated tools in time. Do not touch either of these parts with your bare hands.
- Regular maintenance will reduce the wear and increase the life of the printer.Regularly clean the carbon fiber rod with absolute alcohol or isopropanol, clean the printer body with a dry cloth, wipe off dust, bonded printing materials, and foreign objects on the Z axis.Always unplug QIDI products before performing maintenance or modifications.
- If the machine is in standby mode for a long time,please unplug the power of the QIDI products.
- If the machine is not used for a long time, please pay attention to protect the printer from dust and damp.
- There are manuals, slicer software and other related informations in the USB flash drive. (The information in the USB flash drive may not be the latest. You can obtain the latest information by contacting the After-sales Service marked at the end.)
Power Settings
When products manufactured, we have switched the voltage values according to the sale countries/ regions, but please ensure whether you need to switch it to the voltage values of your region/ country. (The one marked “230V” is suitable for 220V, and the one marked 1111 SV” is suitable for 11 OV; if in doubt, please contact our after-sales technical support.)
Mismatching voltage input will result in products breakdown.
Starting Up
- Take out the top EPS foam and USB flash drive, then lift the printer out of box.
- Remove the packing foam that fix accessory kit and dry box, then take accessory kit and dry box out from top.
- Take out the power cord from the accessory box and plug it into the printer. Turn on the printer and follow the instructions of screen to complete the unboxing process,calibration,etc.
Warning : Before starting up, please confirm whether the voltage setting of the power supply matches the voltage value of your region/country.
Accessory List
Printer Introduction
X-Axis Cleanup
- Wet the carbon fiber rods with alcohol or isopropanol, and gently rub the carbon rods to clean any debris with a dust-free cloth.
- Wet the carbon fiber rod again, and move the print head right and left repeatedly to clean out the dirt in the print head bearing.
- Wipe the carbon fiber tube with a cloth, and repeat steps 3 to 5 until there is no stain on the print head bearing and carbon fiber tube. After cleaning, perform resonance compensation once.
Note : The X-axis rod needs to be cleaned every 1-2 weeks.
How To Remove The Print Head Front Cover
Carefully push upward to unlock the front cover,then remove it.
Specifications
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
After-sales Service E-mail address: Plus3support@qd3Dprinter.com Plus3AMS@qd3Dprinter.com
If you have any suggestions or complaints,please contact with this E-mail address: Audrey@qd3dprinter.com
Official website : www.qd3dprinter.com TEL: 0086-577-66881077
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>