lzf THESIS Omma LED Table Lamp Instruction Manual
- June 1, 2024
- lzf
Table of Contents
lzf THESIS Omma LED Table Lamp
WHAT’S INCLUDE
- 1 x Shade
- 1 x Base
- 1 x Dimmer
- 1 x Plug-in driver
For OMMA P
- 1 x Allen key No. 5
- 1 x Base screw
TECHNICAL SPECIFICATIONS
Integrated LED
ASSEMBLY INSTRUCTIONS
-
MOUNT BASE
Only for OMMA P. Lay the parts on a flat, smooth and padded surface.
Take the base (B) and attach it to the main structure using an Allen key nº 5 and the supplied screw. Make sure to firmly tighten the parts together. -
CONNECT
- ON/OFF: Quick pulse (less than 1 sec.)
- Dimming MIN/MAX: Continuous pressure.
Dimming is memorized on last setting. To reset the dimming level, hold the switch down till it reaches the 100% light intensity, then set the desired level.
THESIS M / OMMA M1 & M2 / TOMO M12 & M18
Example drawing. Plug changes accordingly to the standard of the territory.
USEFUL INFORMATION
Use and care of your lamp.
You have just purchased an original handmade product by LZF. LZF is FSC®
certified, dedicated to promoting responsible forest management worldwide. Our
registered trademark license code isFSC® C110841. Your lamp is made from
natural wood veneer from well-managed FSC® certified forests and other
controlled sources, treated with our patented Timberlite® finish. This
treatment both protects and safeguards the wood veneer against breakages..
CLEANING OF …
The shades we recommend a feather duster or a damp cloth, clean only the flat
surface of the veneer with the cloth, and please avoid any moisture contact
along the edge of the veneer. The metallic surfaces should be treated with
care and cleaned with a soft damp cloth only. Make sure that moisture does not
penetrate joins or junctions between metal parts. Use water. Do not use
solvents or cleaning products of any kind. The acrylic diffusers on your lamp
can be cleaned with a regular window cleaning spray and a soft cloth. Do not
use solvents of any kind.
PRECAUTIONS
-
Luminaire for indoor use only.
Unplug the lamp before cleaning. Servicing or manipulation of the electrical installation should only be performed by qualified electrical personnel or by the LZF service department. -
Glass
Improper handling can cause loosening or chipping of the glass. Any bubbles or lack of homogeneity in the glass is a characteristic feature hand hand-blown glass and not a defect. The surface of the glass may also include imperfections due to its manual manufacturing. When cleaning, use a window cleaning spray and a soft cloth. Avoid handling glass without gloves to prevent fingerprints and loss of gloss. -
Wood veneer
Avoid direct sunlight, strong indirect sunlight and moisture on your lamp. Since wood is a natural material, a gradual change in tone may occur over time. Furthermore, if the lamps were purchased at different times, there will be differences in colour and tone, particularly in lighter-coloured veneers. This is can not be considered a manufacturing defect or reason for complaint. Do not install your lamp near any air-conditioning vents or ventilation shafts as this may damage the wood veneer used in this fixture.
LEDS
If your lamps contains Integrated LED circuits do not touch the LED surface
with your bare hands as this can reduce the life of your LED.
BULBS
Bulbs are normally not included unless indicated. We recommend using energy-
saving LED bulbs. Please refer to the instruction manual or visit our website
www.lzf-lamps.com to make sure you are using the
best bulb for your type of lamp.
KELVINS
Depending on the color of the wood veneer we recommend using different Kelvin
light temperatures, for their optimum appearance: Blue 28, Turquoise 30 and
Grey 29: 4000k Ivory White 20, Natural Beech 22, and Natural Cherry 21: 3000
or 4000k.
Yellow 24, Orange 25, Red 26, Chocolate 31 & Pale Rose 33: 3000k. Learn more
about Kelvins.
©Luziferlamps, S.L All rights reserved. Valencia, Spain. 2020
www.lzf-lamps.com
[email protected]