Haier HRF90UC Beverage Centre Appliance User Manual
- June 1, 2024
- Haier
Table of Contents
Haier HRF90UC Beverage Centre Appliance
Safety information
WARNING: Risk of re/flammable material. The symbol indicates there is a
risk of fire since flammable materials are used. Take care to avoid causing a
fire by igniting flammable material.
Thank You
Thank you for purchasing a Haier Product. Please read these instructions
carefully before using this appliance. The instructions contain important
information that will help you get the best out of the appliance and ensure
safe and proper installation, use, and maintenance. Keep this manual in a
convenient place so you can always refer to it for the safe and proper use of
the appliance. If you sell the appliance, give it away, or leave it behind
when you move house, make sure you also pass this manual so that the new owner
can become familiar with the appliance and safety warnings.
Legend
Warning – Important Safety information
General information and tips
Environmental information
Disposal
Help protect the environment and human health. Put the packaging in applicable
containers to recycle it. Help to recycle waste of electrical and electronic
appliances. Do not dispose of appliances marked with this symbol with the
household waste. Return the product to your local recycling facility or
contact your municipal office.
WARNING!
Risk of injury or suffocation! Refrigerants and gases must be disposed of
professionally. Ensure that the tubing of the refrigerant circuit is not
damaged before being properly disposed of. Disconnect the appliance from the
main supply. Cut off the main cable and dispose of it. Remove the trays and
drawers as well as the door catch and seals, to prevent children and pets from
getting closed in the appliance.
Old appliances still have some residual value. An environmentally friendly method of disposal will ensure that valuable raw materials can be recovered and used again. Cyclopentane, a flammable substance not harmful to ozone, is used as an expander for the insulating foam. By ensuring this product is disposed of properly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused. For more detailed information about recycling this product, please contact your local council, your household waste disposal service, or the shop where you purchased the product, handled by professionals.
Safety information
This product is suitable for the storage of food. Please read the following
safety tips before turning on the appliance for the first time.
Before first use
- Make sure there is no transport damage.
- Remove all packaging keep out of children’s reach and dis- pose them in an environmentally friendly manner.
- Wait at least 0.5 hours before installing the appliance to ensure the refrigerant circuit is fully efficient.
- Handle the appliance always with at least two persons because it is heavy.
Installation
- The appliance should be placed in a well-ventilated place. Ensure a space of at least 50mm above and around the appliance.
- WARNING : Keep ventilation openings, in the appliance enclosed- sure or in the built-in structure, clear of obstruction.
- Never place the appliance in a damp area or location where it might be splashed with water. Clean and dry water splashes and stains with a soft clean cloth.
- Do not place it in a very cold environment. Do not use it outdoors and in the rain.
- Do not install the appliance in direct sunlight or near heat sources(e.g.stoves.heaters).
- Install and level the appliance in an area suitable for its size and use
- Make sure that the electrical information on the rating plate agrees with the power supply. If it does not, contact an electrician- Cian.
- The appliance is operated by a 220V-240 V/50 Hz power supply. Abnormal voltage fluctuation may cause the appliance to fail to start or damage the temperature control or compressor, or there may be an abnormal noise when operating.
- In such cases. an automatic regulator shall be mounted
- Do not use multi-plug adapters and extension cables.
WARNING!
- WARNING: Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.
- WARNING: When positioning the appliance, ensure the supply of the cord is not trapped or damaged.
- Do not step on the power cable.
- Use a separate earthed socket for the power supply which is easily accessible. The appliance must be earthed.
- Only for the UK: The appliance’s power cable is fitted with a 3-cord (grounded) plug that fits a standard 3-cord (grounded) socket. Never cut off or dismount the third pin (grounding). After the appliance is installed, the plug should be accessible.
- WARNING: Do not damage the refrigerant circuit.
Daily use
- This appliance can be used by children aged from 8 years and await rack experience anything sedge I hey hate been given supervision or instruction concerning the use of the appliance safely and understand the hazards involved.
- Children shall not play with the appliance.
- Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances, but not allowed to clean and install the refrigerating appliances.
- Keep children under 3 years of age from the appliance un- less they are constantly supervised.
- Cleaning and user maintenance shall not be done by children without supervision.
- The appliance must be positioned so that the plug is accessible.
- If coal gas or other inflammable gas is leaking into the vicinity of the appliance turn off the valve of the leaking gas, open the doors and windows, and do not unplug the power cable of the appliance.
- Wait at least 7 minutes to reconnect the power after the power has been disconnected
- Do not lift the appliance by its door handles.
WARNING!
- Do not place unstable articles(heavy objects, containers filled with water) on top of the appliance, to avoid personal injury caused by falling or electric shock caused by contact with water.
- Open and close the door only with the handles. The gap between the door and the cabinet is very narrow.
- Do not put your hands in these areas to avoid pinching your fingers. Open or close the appliance doors only when no children are standing within the range of door movement.
- Do not store or use inflammable, explosive, or corrosive material- als in the appliance or the vicinity.
- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
- Do not store medicines, bacteria, or chemical agents in the appliance. This appliance is a household appliance. It is not recommended to store materials that require strict temperatures.
- Do not set unnecessarily low temperatures in the cabinet compartment. Minus temperatures may occur at high settings. Attention: Bottles can burst
- Do not touch the inside surface of the appliance compartment when in operation, especially with wet hands. as your hands may freeze on the surface.
- Unplug the appliance in the event of a power interruption or be used for cleaning. Allow at least 7 minutes before restarting the app- appliance, as frequent starting may damage the compressor.
- WARNING: Do not use electrical devices inside the appliance, unless they are of the type recommended by the manufacturer. To avoid risks a damaged power cord must be replaced by customer service(see warranty card).
- To prolong the service life of the appliance, avoid turning it off.
- Never place the appliance horizontally on the ground. After tilting the appliance more than 45° wait for 24hours before plugging it in.
Maintenance/cleaning
- Make sure children are supervised if they carry out cleaning and maintenance.
- Disconnect the appliance from the electrical supply before routine maintenance. Allow at least 7 minutes be- for restarting the appliance, as frequent starting may damage the compressor.
- Hold the plug, not the cable, when unplugging the appliance.
- Do not clean the appliance with hard brushes, wire brushes, tergent powder, petrol, amyl acetate, acetone, and similar organic solutions, acid or alkaline solutions. Please clean with soapy water to avoid damage.
- Rinse thoroughly with water and wipe dry.
- Do not use cleaning powders or other abrasive cleaners. Do not wash removable parts in a dishwasher.
- WARNING: Do not use mechanical devices or other means to access celebrate the defrosting process, other than those recommended by the manufacturer.
- If the supply cord is damaged, it must be replaced by the menu- factor, its service agent, or similarly qualified persons to avoid a hazard.
- Do not try to repair, disassemble, or modify the appliance by your- self. In case of repair please contact our customer service.
- If the illuminating lamps are damaged, they must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
- Use a Vacuum to clean the dust on the back of the unit at least once a year to avoid hazards by fire, as well as increased energy consumption.
- Do not spray or flush the appliance during cleaning.
- Do not use water spray or steam to clean the appliance.
- Do not clean the cold glass door with hot water. Sudden temper- nature change may cause the glass to break.
- If you leave your appliance out of use for an extended period, leave it open to prevent odor and unpleasant smells from building up inside.
Refrigerant pass information
WARNING!
The appliance contains the flammable refrigerant ISOBUTANE (R600a). Make sure
the refrigerant circuit is not damaged during transportation or installation.
Leaking refrigerant may cause eye injuries or ignite. If damage has occurred,
keep away open fire
sources, thoroughly ventilate the room, and do not plug or unplug the power
cords of the appliance or any other appliance. Inform customer service.
In case of eyes come into contact with the refrigerant, rinse it immediately-
diately under running water and call immediately the eye specialist.
WARNING: The refrigeration system is under high pressure. Do not tamper
with it. Since the flammable refrigerants are used, please. install, handle,
and service the appliance strictly according to the in-construction and
contact the professional agent or our after-sales service to dispose of the
appliance.
Intended use
This appliance is intended to be used in households and similar applications such as
- staff kitchen areas in shops, offices, and other working environments- menus:
- farmhouses and by clients in hotels, motels, and other residents- title-type environments:
- bed and breakfast type environments;
- catering and similar non-retail applications.
- To ensure the safe preservation of food, please comply with this instruction for use.
- The details on the most appropriate part in the compartment of the appliance where specific types of food shall be stored, con-
- The distribution of temperature that can be present in the different compartments of the appliance is in the other part of the manual.
- Changes or modifications to the device are not allowed. Union-tended use may cause hazards and loss of warranty claims.
Disposal
The 1 symbol on the product or its packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly, will help prevent potential negative consequences for the environment and human health, which could otherwise, be caused by inappropriate waste handling of this product- cut. For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product. Since the flammable insulation blowing gases are used, please contact the professional agent or our after-sale service to dispose of the appliance.
WARNING!
Risk of injury of suffocation! Refrigerants and gases must be disposed of
professionally. Ensure that the tubing of the refrigerant circuit is not
damaged before being properly disposed of. Disconnect the appliance from the
main supply. Cut off the main cable and dispose of it. Remove the trays and
drawers as well as the door catch and seals to prevent children and pets from
getting closed in the appliance.
Maintenance
- WARNING: Disconnect the appliance from the power supply be- for cleaning.
- Do not clean the appliance with hard brushes, wire brushes, detergent powderpetrol, amyl acetate, acetone, and similar organic solutions, acid or alkaline solutions. Please clean with soapy water to avoid damage.
- Clean the appliance when only little or no food is stored It is only necessary to clean it when it is dirty.
- Clean the inside and housing of the AP- appliance with a sponge damped in warm water and neutral detergent
- Rinse with clean warm water and dry with a soft cloth.
- Do not clean any of the parts of the ap- appliance in a dishwasher.
- Allow at least 7 minutes before re-starting the appliance as frequently may damage the compressor.
Clean the door gasket
- The door gaskets should be cleaned every 3 months to ensure a proper seal. As below: Remove: Grasp the door gasket and pull it out according to the direction of the row to remove the whole door gasket in order.
- First, use a brush to clean the gasket grooves, then wipe the sealing surface with a soft damp cloth. Finally, dry the gasket with a clean towel.
Installation of door gasket after cleaning
Before installation, make sure that there is no water on the door gasket.
Insert the door gasket into the groove, and press the door gasket tightly from
the top to the bottom by hand until the whole door gasket is inserted into the
groove.
Cleaning the shelves
- All shelves can be taken out for cleaning.
- Take out all food.
- Lift each shelf a little and take it out.
- Clean the shelf with a soft damp cloth.
- Wait until the shelves are dry before putting them back in.
WARNING
Wait at least 7 minutes to reconnect the power after the power has been
disconnected.
Accessories
Check the accessories and literature by this list:
Product Description
Notice
Due to technical changes and different models, some of the illustrations in
this manual may differ from your model.
Picture of appliance
- Wine Rack
- Shelf
- Wire barrier
- Adjustable feet
- LED Lamp
- Display
- Glassdoor
Installation
Unpacking
- Take the appliance out of the packaging.
- Remove all packaging materials including the foam base and all adhesive tape held- in the accessories.
Environmental conditions
The room temperature should always be between 10 °C and 43 °C since it can
influence the temperature inside the appliance and its energy consumption. Do
not install the application- anywhere near other heat-emitting appliances
(ovens, refrigerators) without isolation.
Space requirements
Required space to open the door (Fig. 1,2,3,4): For safety and energy reasons,
the required ventilation distance of 50 mm in all directions must be
observed(Fig.5).
WARNING!
Keep ventilation openings in the appliance or the in-built structure clear of
construction. This refrigerating appliance is not intended to be used as a
built-in appliance
Aligning the appliance
The appliance should be placed on a flat and solid surface.
- Tilt the appliance slightly backward (Fig. 7).
- Set the adjustable front feet to the desired level by turning them.
- Check the stability by pushing on the corners and adjusting as required to balance the product. If the pro-duct is not balanced the door seals may leak. Raising the front of the product slightly helps the closing of the door.
Fine-tuning of the door
The appliance closes more easily if the leveling feet on the front are used:
Rotate the adjustable feet (Fig. 8) to turn them up or down:
- Turning the feet clockwise raises the appliance.
- Turning the feet counterclockwise lower the apple- ance.
Waiting time
The maintenance-free lubrication oil is located in the capsule of the
compressor. This oil can get through the closed pipe system during transport
if the apple- ance is tilted. Before connecting the appliance to the power
supply, wait 0.5 hours (Fig. 9) so that the oil runs back into the capsule.
Electrical connection
Before each connection check if:
- power supply, socket, and fusing are appropriate to the rating plate. the power socket is earthed and no multi-plug or extension.
- the power plug and socket are fit properly. Connect the plug to a properly installed household socket.
WARNING!
To avoid risks a damaged power cord must be replaced by customer service (see
warranty card).
Use
Before first use
- Remove all packaging materials. This includes the foam base and all adhesive tape holding the cooled appliance accessories inside and outside. Keep them out of children’s reach and dispose of them in an environmentally friendly manner.
- Clean the inside and outside of the appliance with water and mild detergent before putting any beverages in it.
- After the appliance has been leveled and cleaned, wait for at least 30 minutes before connecting it to the power supply. If your appliance has been tilted for any reason, wait 24 hours before plugging it in. See section INSTALLATION.
- Once you have plugged the unit into an electrical outlet, let the unit run for at least 30 minutes to acclimatize itself before making any adjustments. The temperature is automatically set to 10 °C. If desired, you can change the team- perature manually. Please see the Temperature Setting
Press key
The keys on the control panel are press buttons, which respond when lightly
pressed with the finger.
Description of the control panel
- A Display
- B Temperature adjust key: down
- C Temperature adjust key: up
- D Super cool key
- E Light key
Temperature setting
Presetting
- Once you have plugged the unit into an electrical outlet, let the unit for at least 30 minutes to acclimatize itself before making any adjustments.
- When the appliance is switched on after disconnection from the main power supply. it may take several hours for the correct temperatures to be reached. The exact time varies depending on the environment and the temperature setting.
- Press the B or C key the display will start to flash. Press the B or C key to set the desired temperature. The temperature setting range: is 2-12°C. After 5 seconds the temperature will be confirmed.
Notice
Influences on temperatures
The temperature inside the appliance is influenced by the following factors:
- Ambient temperature
- Amount of stored foods
- Frequency of door opening
- The location of the appliance
The default setting is 10°C
When the display stops blinking, the display shows the current setting
temperature. If you are using the Cooled Appliance to store food we recommend
setting the product to 3 C
Lighting mode setting
Press the E key to turn on the light. Press the E key again to turn off the
light. The light will stay on for 10 minutes. After the light is lit, the
light will be turned off without any key operation within 10 minutes.
Power-Off Memory function
If a power outage, the appliance will automatically save the set temperature.
After power recovery, it will run based on the temperature set before the
power outage.
Super cooling function
When the display is on, press the “D” key, the S.Cool will light up, and the
system will enter the super cooling function.
- In the supercooling state, press the “D” key again, the S.Cool light is off, and the system exits the supercooling state;
- After entering the super cooling function, the “S.Cool” is always lit. The super cooling function will automatically exit and return to the original set function mode after running for 6h.
- The temperature cannot be adjusted under the super cooling function.
Energy saving tips
Make sure the appliance is properly ventilated (see INSTALLATION).
- Do not install the appliance in direct sunlight or near heat sources (e.g. stoves, heaters).
- Avoid unnecessarily low temperatures in the appliance. The energy consumption increases the lower the temperature in the appliance is set.
- Open the appliance door as little and as briefly as possible.
- Do not exceed the designed amount of bottles to avoid obstructing the airflow.
- Keep door seals clean so that the door always closes correctly.
- The most energy-saving configuration requires drawer, food box and shelves to be positioned in the appliance in factory-fresh condition, and food to be placed without blocking the air outlet of the duct.
Equipment Shelf
- The shelves are designed for easy storage and removal of beverages. They can be cleaned with a soft damp cloth.
- The quantity can vary from the depicted number of bottles if they are stacked differently.
Advice for the layout of your shelf
We recommend that the number of wine bottles should not exceed two layers on
each shelf and the bearing capacity of the wine shelves should not exceed 15
kg. Before placing the bottles inside the appliance, confirm whether or not
the wine shelves are completely
stable In addition. confirm whether or not any bottle protrudes from the
shelves to prevent bottles from hitting the glass door upon closing.
Notice
It is not recommended to store vegetables and other food in the product. Store
beverages more than 5cm away from the duct cover to avoid blocking the air
vents.
Care and cleaning
Defrosting
The defrosting of the appliance is done automatically; no manual operation is
needed.
Replacing the LED lamp
DC 12V, max Power 2W. We recommend contacting a service person to replace the
LED lamp.
Non-use for a longer period
- Unplug the power cord.
- Clean the appliance and door gaskets as described above.
- Keep the door open to prevent the creation of bad odors inside.
Moving the appliance
- Remove all food and unplug the appliance.
- Secure shelves and other moveable parts in the appliance with adhesive tape.
- Do not tilt the appliance more than 45° to avoid damaging the refrigerating system.
Troubleshooting
Many occurring problems could be solved by yourself without specific expertise. In case of a problem please check all shown possibilities and follow the below instructions before you contact an after-sales service. See CUSTOMER SERVICE.
WARNING!
- Before maintenance, deactivate the appliance and disconnect the mains plug fromthe mains socket.
- Electrical equipment should be serviced only by qualified electrical experts because improper repairs can cause considerable consequential damages.
- A damaged supply should only be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
Troubleshooting
Technical data
Explanations
- Based on standard test results for 24 hours. The actual power consumption depends on the actual environment, the amount of bottling, the set temperature, the door opening and closing, etc.
- The nominal power consumption is the value obtained according to the standard test when the wine cabinet does not turn on the internal light.
- extended temperate: ‘This refrigerating appliance is intended to be used at ambient temperatures ranging from 10 °C to 32 °C’;
- temperate: ‘This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C’;
- subtropical: ‘This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C’;
- tropical: ‘This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C’;
Customer Service
We recommend our Haien Customer Service and the use of original spare parts.
If you have a problem with your appliance, please first check the section
TROUBLESHOOTING. If you cannot find a solution there, please contact your
local dealer.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>