Emerson 2.20F03 Update Advisory Supervisory Control Platform Firmware Instruction Manual

Update Advisory Supervisory Control Platform
Firmware 2.20F03
Release Notes

2.20F03 Update Advisory Supervisory Control Platform Firmware

A new general release version of the Supervisory controller firmware version 2.20F03 has been released and is available for customer upgrade. For more information, visit the Supervisory Control page on the Emerson website:
https://climate.emerson.com/en-us/products/controls-monitoring-systems /facility-controls-electronics/facility-and-system-controls/lumity- supervisorycontrols-platform
IMPORTANT:

1. For E3 firmware upgrades, be sure to use the _Display_Update file.
2. Reset or power cycle an upgraded E3 approximately10 minutes after the upgrade is complete.
   

Who Should Update
Emerson recommends that all customers upgrade their Supervisory controllers and PCs running Connect+ to the latest version to take advantage of the latest fixes and enhancements listed in Table 3.
All customers who use any of the features below are advised to upgrade to Supervisory controller 2.20F03, and customers using any of the features listed in Table 

CONNECT+ UPDATE REQUIRED

Table 1 – Supervisory Controller and Connect+ Compatibility Matrix

It is recommended to upgrade to the latest Connect+ version. If you plan to upgrade Supervisory controllers and Connect+ at the same time, upgrade Connect+ to the latest version first, then update the Supervisory controllers. Contact Emerson for more information about upgrading.

CONTROLLER FIRMWARE COMPATIBILITY

Table 2 – Firmware Platform Mapping

Square D Application

Maximum allowed devices increased from 8 to 16.|
Security
General enhancements.|
ECT Modbus
Communication Stats section is now added to ECT Modbus Devices, such as Copeland
Discus, CoreSense, and others.| ,./
Firmware Upgrade – Backup/Restore
A Site Supervisor or E3 configured as the site aggregator can now initiate firmware
updates, backups, and restore backup files for E2 controllers.| ✓
Onboard 10 Digital Input Active State (Site Supervisor only)
Active state parameters for Onboard I/O, are now user configurable.| ✓
AHU Air Handlers
Enhancements to the Air Handlers application, including Dehumidify strategies,
minimum off time for cooling and dehumidification stages.| ✓

Table 3 – Supervisory Controller 2.20F03 Feature and Fix Matrix

Feature and Fix Descriptions| Supported In
Supervisory
Controllers 2.20F03
---|---
Fixes|
Static Route IP

The controller no longer needs to be rebooted when a 1JSEI stick is plugged in with the
delete_static_route file removed.| ✓
XM Circuit Application
The Mix Pct association was removedf or all XM/XR devices when associated with an XM
Circuit.| ✓
Floorplans
Customer Floorplans nolonger show an error with the text ‘Standard Circuits Graphical
Status does not exist.’
  Points value and status are now displayed correctly after overriding an E2 point that
cannot be overridden.| ✓
SOAP
The interface SetPointValue is now functioning properly.| ✓
Online Help
•XM679 3.4
General help enhancements and Min/Max values are now correct.
•XM678 2.8
Help added for parameters that were missing definitions.
•Alarm Communications
Help support added.| ✓
BACnet
BACnet IP Broadcast is now supported.| ✓
MODBUS Calculator
If some of the devices are Unknown in the MODBUS Calculator. it can now be
determined if there is an overload of devices in the Site Supervisor configuration.| ✓
IPX Devices
The IPX device Al Inputs’ values are no longer empty after changing CfgAl type from
to when these are| ✓
NTC Digital Input IPX devices Offline.
Standard Circuit Application
The start defrost cycle for the second circuit is now automatically scheduled to add 30
minutes after the start defrost cycle of the first circuit, when two circuits are the same case type.| ✓
MRLDS•450 Application
Sending the Application Command ‘Clear CalibrationCommand-will no kInger result in
an error.| ✓
XC1000 Device
The Site Supervisor parameter is no longer read from the device when CfgSyn Action is
set to Write to Device.| ✓

Table 3 – Supervisory Controller 2.20F03 Feature and Fix Matrix

Features and Fix Descriptions| Supported in
Supervisory
Controllers 2.20F03
---|---
Flex Combiner Application

Flex Combiner auto association now allows users to enter a colon’:- in the Description
field manually.| ✓
Controller Offline (E3 Controller Only)
General code enhancements applied to reduce the probability of having to power cycle
the controller.| ✓
System Time Settings
The order of the Time Zone and Time Setting fields has been reversed so that the
Tine Zone field now appears first.
System Time is now displayed when NTP is Enabled.| ✓
Refrigerant Support
R454C supported added.| ✓
Restore
•UltraSite toSite Supervisor and E3
The “+” is no longer missing in the Flexible Combiner’s equation after restoring the .003 file to Site Supervisor.
AHU Large parameters are now restoring correctly.
Analog Sensor Control parameters are now restoring correctly.
•USB & SD Card
The progress bar is no longer showing 0% during file upload when restoring the setpoint file from a 058 and SD card.
•System
Restore verification will no longer fail when attaching customer setpoints.| ✓

Table 3 – Supervisory Controller 2.20F03 Feature and Fix Matrix

Update Supervisory Controller firmware

For more information on firmware upgrades, see the 026-4184 Upgrade Advisory:
https://climate.emerson.com/documents/026-4184-upgrade-advisory-for-all- supervisory-controller-versions-before-2-19f01-en7981974.pdf
For more information on E3 firmware upgrades before 2.20F03, see the 026-4185 Upgrade Advisory
https://climate.emerson.com/documents/026-4185-upgrade-advisory-for-e3 -controller-versions-below-2-20f03-en-8070726.pdf
Supported Browsers

• Microsoft Edge v88 and later
• Mozilla Firefox 11 and later
• Google Chrome 61.0 and later
• Apple Safari® on iOS10 (iPhone® 5C, iPad® 4) and later
• Webview on Android 5.0 (Samsung Galaxy S4) and later

For Emerson Digital Cold Chain Technical Support

•  833-409-7505
• ColdChain.TechnicalServices@Emerson.com

https://climate.emerson.com/en-us/products/controls-monitoring-systems /facility-controls-electronics/facility-and-system-controls/lumity- supervisory-controls-platform
Document Part # 026-4081 Rev 1
This document may be photocopied for personal use.
Visit our website at www.climate.emerson.com for the latest technical documentation and updates.
Join Emerson Technical Support on Facebook http://on.fb.me/WUQRnt
For Technical Support call 833-409-7505 or email ColdChain.TechnicalServices@Emerson.com
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. Emerson reserves the right to modify the designs or specifications of such products at any time without notice. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user. ©2022 Emerson is a trademark of Emerson Electric Co.
MERSON. CONSIDER IT SOLVED.

Documents / Resources

| Emerson 2.20F03 Update Advisory Supervisory Control Platform Firmware [pdf] Instruction Manual
2.20F03, 2.20F03 Update Advisory Supervisory Control Platform Firmware, Update Advisory Supervisory Control Platform Firmware, Supervisory Control Platform Firmware, Control Platform Firmware, Platform Firmware
---|---

References

• Log into Facebook | Facebook
• Copeland | Copeland US
• Controls & Monitoring Systems | Copeland US
• Lumity Supervisory Control Platform | Copeland US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>