AUTELO F3698 BK Ceiling Fans with Lights Installation Guide

AUTELO F3698 BK Ceiling Fans with Lights

ANY QUESTIONS PLEASE CONTACT US FREELY
We will be there for you 7/24 hours of customer service.

• EMAIL: autelo_service@outlook.com

SAFETY INFORMATION

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SANE INSTRUCTIONS.

1. To reduce the risk of electric shock. ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be by the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting 13.5 lbs. (6.1 kg). Use only UL-listed outlet boxes marked Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”.
4. The fan must be mounted with a minimum of 7.5 ft.(2.3 m) clearance from the trailing edge of the blades to the floor.
5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
6. Do not place objects in the path of the blades
7. To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
8. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and marked suitable for use with the model fan you are installing Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
10. All setscrews must be checked and re-tightened where necessary before installation.

• WARNING: To avoid possible electrical shock. make sure that the electricity is turned off at the main power box before starting work. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
• WARNING: To reduce the risk of fire electrical shock or personal injury, ensure that the fan mounting brackets are supported directly from the building structure or the outlet box marked “Acceptable for Fan Support of 35 lbs. (15.9 kg)or less”. Use only the screws provided with the outlet box.
• WARNING: To reduce the risk of personal injury. do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
• WARNING: To reduce the risk of fire or electric shock this fan is NOT suitable for use with solid-state speed controls.
• WARNING: Electrical diagrams are for reference only Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.

WARRANTY

The supplier warrants the fan motor to be free from defects in workmanship and material present at the time of shipment from the factory for a time after the date of purchase by the original purchaser. The supplier also warrants that all, other fan parts, excluding any glass or acrylic blades, be free from defects in workmanship and material at the time. Of shipment from the factory for two years after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace them with a comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions, this warranty does not cover any changes in brass finish, including rusting. patina corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hereby disclaims any warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty that cannot be disclaimed is limited to the period specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

TOOLS REQUIRED

FAN PARTS INCLUDED

1. Ceiling Plate(*1)
2. Motor(*1)
3. Block Set(*5)
4. Blade Arm(*5)
5. Fan Blade(*5)
6. Metal Lampshade(*1)
7. Receiver + Remote Control(*1)
8. Blade Screw+Washer(*15)
9. Canopy Cover(*1)
10. Horn Cover(*1)
11. Downrod(10″*1)
12. C Ring(*1)
13. Mounting Screws For

C Ring(*4)

1. Please check all compare all parts with the package contents parts are present. list and hardware contents list. If any part is missing or damaged, please contact us for help.
2. We strongly recommend that you please watch our install video of this fan. We will provide install guidance step by step. The installation video is in our product listing, click on the video place (after the product picture), and it will be there.

HARDWARE INCLUDED

1. Expansion Screw(*2)
2. Wood Screw (*4)
3. Machine Screw+Washer (*2)
4. Wire Connector (*3)
5. Blade Balancing Kit (*1)

EXPLODED VIEW

INSTALLATION PRE-CHECK

Pre-Check
The distance from the fan blade to the ground shall not be less than 7.5 ft（2.3 m) and at least 3.2 ft (1 m) away from the wall.

Security Procedure

• Turn OFF the electrical power at the main fuse or circuit breaker.

Wiring Port Of Ceiling Fan:
The fan must be able to be fixed on the ceiling building and connected to the outlet.

INSTALLATION OF HANGING BRACKET

For Concrete Ceiling:
Drilling a pilot hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor and cleaning out the hole of all debris. Knock the expansion screw into the hole and then tighten it with a wrench.

For Wooden Ceiling:
Drill a pilot hole in your ceiling with the power drills first, then secure the plate with wood screws.

1. Install the ceiling plate on the ceiling with corresponding screws(Fig 1).
   WIRING OF CEILING FAN

2. Hang the fan to a “J” shaped hook, then wire as described. (Fig 2-3)
   HANGING OF CEILING FAN

3. Fix the canopy and motor to the ceiling plate with screws. (Fig 2)
   INSTALLATION OF BLADES & LIGHT KIT

Attention: Mark as “Blade on this side” on the blade arm facing down on the blades.

1. Attach the block set to the blade side you want to use and place the blade arm on the blades. Then fix them with blade screws. (Fig 1)
2. Install the fan blades onto the motor in turn and tighten them with mounting screws. The side has block sets facing down. (Fig 2)
3. Rotate to take down the lampshade. loosen screws on the metal plate then attach the metal lampshade to the motor and tighten it on the metal plate with screws. (Fig 3-4)。
4. Place the lampshade and finish the installation. (Fig 6-7)

EXPLODED VIEW

INSTALLATION PRE-CHECK

Pre-Check
The distance from the fan blade to the ground shall not be less than 7.5 ft（2.3 m) and at least 3.2 ft (1 m) away from the wall.

Security Procedure

• Turn OFF the electrical power at the main fuse or circuit breaker.

Wiring Port Of Ceiling Fan:
The fan must be able to be fixed on the ceiling building and connected to the outlet.

INSTALLATION OF HANGING BRACKET

For Concrete Ceiling
Drilling a pilot hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor and cleaning out the hole of all debris. Knock the expansion screw into the hole and then tighten it with a wrench.

For Wooden Ceiling
Drill a pilot hole in your ceiling with the power drills first, then secure the plate with wood screws.

1. Install the ceiling plate on the ceiling with corresponding screws(Fig 1).
   INSTALLATION OF CANOPY

2. Put the C ring into the canopy. The smooth and flat side of the C ring is facing down. Alignment hole position to 4 ostiole. Screws are driven in from the bottom of the canopy. Then use 4 screws to fix the C ring on the canopy. (Fig 2-3).

INSTALLATION OF DOWNROD & HANGER BALL

1. Loosen the screw and take out the lateral pin. Take out the hanger ball. (Fig 1)
2. Take out the canopy, canopy cover, and horn cover and place them with the download in turn to the hanger head. Then place the hanger ball on the top of the download, put the lateral pin inside the hanger ball, and fix it with screws. (Fig 2-3)
3. Insert the cross pin to the download and cross R pin to the hole on the latch. Fix the screws on the hanging head to tighten the download. (Fig 4-5)

WIRING OF CEILING FAN

HANGING OF CEILING FAN

1. Turn the hanger ball so that the groove is clamped on the lug on the C ring to stabilize the ceiling fan. (Fig 1)
2. Place the receiver inside the canopy. (Fig 2)
3. Place the canopy on the top of the ceiling and tighten the screws on the ceiling plate to fix it. (Fig 3)
4. Place the canopy cover under the canopy. (Fig 3)

INSTALLATION OF BLADES & LIGHT KIT

Attention: Mark as “Blade on this side” on the blade arm facing down on the blades.

1. Attach the block set to the blade side you want to use and place the blade arm on the blades. Then fix them with blade screws. (Fig 1)
2. Install the fan blades onto the motor in turn and tighten them with mounting screws. The side has block sets facing down. (Fig 2)
3. Rotate to take down the lampshade. loosen screws on the metal plate then attach the metal lampshade to the motor and tighten it on the metal plate with screws. (Fig 3-4)

DETAILS OF REMOTE CONTROL

REVERSIBLE FUNCTION OF FAN

• Press the forward & reserve buttons to achieve airflow down and upward for summer and winter different needs.

FAN BALANCE
If the ceiling fan has a wobble problem, you can please try the ways below.

1. Clip the clip in the middle of the fan blade. Turn on the fan. If the oscillation still exists, replace the clip with another blade until the oscillation decreases. Then this blade needs a balance sticker.
2. Please put the clip on the blade that needs to be balanced and try to put it in the best position, from the center of the blade to the tip, until the swing disappears.
3. Stick the balance on the side of the leaf near the clip, remove the clip, and test the fan rotation. If it continues to swing. Use another counterweight. If the situation changes badly, try another area placement. Please try patiently until the fan balance is stable.

TROUBLESHOOTING

Please read all installation instructions carefully.

WARNING
Before servicing or cleaning your fan, switch the power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally.

Fan not responding to remote control

• Check that all wire connections are secure and made as instructed.
• Verify that power is on and reaching the receiver by a voltmeter.
• Verify that controller batteries are installed with proper polarity as indicated inside the battery cover.

Light does not work

• Check wire connections at the ceiling and receiver.
• Confirm that LED wire leads and terminal block are properly connected to the LED board.

The fan makes a repetitive ticking noise

• Check for obstructions in the rotor path.
• Make sure the mounting hardware at the ceiling is secure.
• Make sure all other hardware and blade attachments are tight.

The fan makes a humming noise

• Be sure you are using the control set supplied with your fan
• Make sure all fittings are firmly secured, Loose parts will often cause vibrational noise or humming. Removal and re-attachment can sometimes remedy such resonant vibrational noise.

Fan wobbles

• Use the balancing kit.
• Make sure the mounting plate and hardware at the ceiling are secure and firmly fastened. If necessary, use the wood screws provided to further secure the outlet box to the joist.
• Carefully lower the motor housing and verify that the mounting plate is secure to the outlet box, the screws are tight.

If the above solutions can not help you to solve the problem Please contact us at: autelo_service@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>