Shenzhen Feelstorm Technology Co Ltd BM904B Video Baby Monitor User Manual

: June 1, 2024
: Shenzhen Feelstorm Technology Co Ltd

Table of Contents

SAFETY INSTRUCTIONS
STATUS BAR
PRODUCT DIAGRAM
GETTING STARTED
FUNCTIONS & OPERATIONS
MULTIPLE-CAMERA OPERATION
SPECIFICATIONS
FCC STATEMENT
IC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shenzhen Feelstorm Technology Co Ltd BM904B Video Baby Monitor

Shenzhen Feelstorm Technology Co Ltd BM904B Video Baby
Monitor

SAFETY INSTRUCTIONS

Adult assembly is required. Keep small parts away from the children when assembling.
Avoid placing the unit or cords in the cot or within baby’s reach. Keep at least 1 meter away.
Do not touch plug contacts with sharp or metal objects.
Keep the product away from water or heat sources.
ONLY use the power adapters provided.

CAUTION

This product is not a toy. Do not allow children to play with it.
This baby monitor is not a substitute for responsible adult supervision.
About Echo:If the monitor is too close to the camera, an echo may occur. Keep them apart or lower the volume to eliminate noise.
The camera has no built-in battery; It MUST be connected with a power adapter while working.
Charging the monitor fully before use is recommended; it operates on battery during power failures.
Unplug the product when unused for extended periods or during lightning storms.
Clean the camera with soft DRY fabric.
For indoor use only

STATUS BAR

Status Bar

Signal Strength Indicator
Channel Selected
Temperature Of The Baby’s Room
Zoom Level
Lullaby Plays
VOX Function Activated
Alarm Activated
Time
Battery Power
Selective View Activated
Volume Bar
Brightness Bar
PTT Function Activated

PRODUCT DIAGRAM

Monitor / Parent Unit	Camera / Baby Unit

Product Diagram

Signal LED Indicator
Charging LED Indicator
Power ON / OFF / Sleep Button
Menu / OK Button
VOX Mode Button
ZOOM Button
Navigation Buttons
Lullaby Control / PTT Button
Microphone
Volume Level LED
LCD Screen
Kickstand
Speaker
Power Adapter Port

| Product Diagram

Light Sensor
Camera Lens
Power indicator
Microphone
Infrared LED
Power Switch
Power Adapter Port
Temperature Sensor
Pair key
Speaker

GETTING STARTED

Step 1. Powering the Camera / Baby Unit

Plug the power adapter into an electrical outlet and connect it to the Type-C port on the camera.
A BLUE indicator will light up when the camera is running (optional).

Step 2. Charging the Monitor / Parent Unit

Plug the power adapter into an electrical outlet and connect it to the Type-C port on the monitor.
A BLUE indicator will light up, indicating that the battery is charging.
Press and hold the Power button for at least 3 seconds to turn the monitor on.

Step 3. Camera Registration

Press Menu / OK to enter the registration interface. Choose [Camera->Add Camera-> Camera 1], then press Menu / OK to confirm registration.
Press the Pair button on the back of the camera within 15 seconds to complete the registration.

Note: The camera is pre-registered by default. You only need to re- register if the camera loses connection with the monitor.For additional details on managing multiple cameras, please refer to the MULTIPLE-CAMERA OPERATION instructions.

Step 4. Placing the Camera

Position the camera in a convenient location, such as on a table, and aim the camera lens towards the desired monitoring area.
Adjust the camera ‘ spangle until you are satisfied with the image in the monitor.

Note: DO NOT position the camera within the baby’ search. If there is any interference with the image or sound, try relocating the units to different spots, ensuring they are not too close to other electrical equipment.

FUNCTIONS & OPERATIONS

Adjusting monitor’s volume
Use the UP / DOWN button to adjust the volume. The current volume icon will stay on the screen for 3 seconds.
Adjusting screen’s brightness
Press the Right / Left buttons to adjust the screen brightness.
Intercom function
Hold PTT Button on the monitor to speak to your baby through the camera’s speaker. A microphone icon will appear on the screen.
Digital zoom & selective view
Press the Zoom Button to zoom in on the screen image. Choose from three levels of magnification (1X / 2X / 3X switching in cycle).
Press the corresponding navigation buttons to move the image to the desired view.
Night vision
When ambient light is insufficient, the camera automatically enters Night Vision Mode, the image turns to black and white.
Audio mode
Quickly press the Power Button to activate Audio Mode, unavailable if VOX is on. In Audio Mode, the screen shuts down, saving energy while audio transmission continues. Press any button to exit Audio Mode.
Main menu
Press Menu/OK in the monitoring interface to enter the main menu, containing 6 items.
Use the navigation buttons to move the cursor, select an item, and press Menu / OK to enter the submenu. Press the Back button to return to the monitoring interface.
Camera:
Add Camera: Refer to GETTING STARTED-Step 3 for instructions.
Camera Power Light: Set the power indicator on the camera to Auto / Always On / Always Off on the monitor.
Intercom Volume: Adjust the intercom volume heard on the camera to Low / Medium / High level.
Alarm
Press Menu / OK to enter editing mode or confirm the current item.
Press Up / Down to skip to the next item
Press Left / Right to change the value.
Press Back to go back to the previous menu.
Settings
Time: You can switch the time format to a 24H or 12H clock. To adjust the time, use the Up / Down buttons to change the value and the Right / Left buttons to move the cursor.
Temperature Unit: Choose between Celsius or Fahrenheit.
Anti-Flicker: Select 50/60 Hz options to match your local power frequency for anti-flicker.
Alerts Tone: Toggle the alert tone of low battery and interrupted connection. Choose from three tones.
Monitor LED Light:Toggle the status of the LED indicator on the parent unit: OFF / Low / Medium / High
LCD Backlight: Adjust the brightness and screen activity time.
VOX (Voice Activation):
In VOX mode, the screen sleeps to save energy and wakes up when the camera’s mic hears a sound. Press the VOX Mode Button or use the VOX submenu to enable / disable this mode.
System Mode: Switch between Normal Mode and VOX Mode.
VOX Sensitivity: Adjust sensitivity to Low / Medium / High.
Language
Choose from 8 languages: English / Français / Español / Português / Italiano / Deutsch /
Türkçe / Русский.
System Info:
System Info: View hardware and software versions.

MULTIPLE-CAMERA OPERATION

Add / Delete Camera:
- Press Menu / OK to enter the registration interface. Select [Camera-> Add Camera->Camera 2], then press Menu / OK to confirm registration.
- Press the Pair button on the back of the camera within 15 seconds to complete registration.
- Same process applies to registering more cameras.
- To disconnect a camera, select [Delete Camera], choose the associated camera, and press Menu/OK to cancel registration.
  Note: One monitor can pair with up to four appointed cameras simultaneously,including both fixed-view and pan-tilt cameras.
Change Camera Channels:
- Select [View Camera] then press Menu / OK on the desired Camera channel (Camera 1 / Camera 2 / Camera 3 / Camera 4).
- For automatic channel changes, choose [Scan] and press Menu / OK. Then select [Scan Delay] to set the intervals for view changes (10 / 15 / 20 / 30 seconds).
- On the monitoring interface, press and hold the Left or Right Button to cycle through channels quickly.
Change settings on different cameras:
Adjusting settings on one camera on the monitor will update settings for all connected cameras, including VOX mode on / off, camera speaker volume, and camera LED Auto / On / Off. The digital zoom& selective view function is the only setting that cannot be changed simultaneously

SPECIFICATIONS

General:

FCC STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC SAR Information Statement

Your Video Baby Monitor is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for Video Baby Monitor employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the Video Baby Monitor transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the Video Baby Monitor while operating can be well below the maximum value. This is because the Video Baby Monitor is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a Video Baby Monitor model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this Video Baby Monitor when worn on the body, as described in this user guide, is 0.09 W/Kg (Body-worn measurements differ

among Video Baby Monitor models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various Video Baby Monitor and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this Video Baby Monitor withall reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines.

SAR information on this Video Baby Monitor is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: 2AFX2BM904-1 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com. * In the United States and Canada, the SAR limit for Video Baby Monitor used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. The SAR test distance is 0mm.

IC STATEMENT

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications

IC SAR Information Statement

Your Video Baby Monitor is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Innovation, Science and Economic Development Canada of the Canada Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for Video Baby Monitor employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the ISED is 1.6 W/kg. Tests for SAR are conducted with the Video Baby Monitor transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the Video Baby Monitor while operating can be well below the maximum value. This is because the Video Baby Monitor is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a Video Baby Monitor is available for sale to the public, it must be tested and certified to the ISED that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the ISED for each model. The highest SAR value for this Video Baby Monitor when worn on the body, as described in this user guide, is 0.7909 W/Kg (Body-worn measurements differ among Video Baby Monitor, depending upon available accessories and ISED requirements). While there may be differences between the SAR levels of various Video Baby Monitor and at various positions, they all meet the government requirement for safe exposure. The ISED has granted an Equipment Authorization for this Video Baby Monitor with all reported SAR levels evaluated as in compliance with the ISED RF exposure guidelines. SAR information on this Video Baby Monitor is on file with the FCC and can be found under the Display Grant section of https://sms-sgs.ic.gc.ca/after searching on IC: 29356-BM90401 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com. In the United States and Canada, the SAR limit for Video Baby Monitor used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.The SAR test distance is 0mm.