BOSCH PWS 700 Angle Grinder Instruction Manual

PWS
700 | 7000 | 7-115 | 700-115 | 700-125 | 730-115 | 750-115 |
750-125 | 7500 | 780-125 | 8000 | 850-125 | 8500-125

PWS 700 Angle Grinder

Safety instructions

General Power Tool Safety Warnings
WARNING
Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electricity.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts.**** Damaged or entangled cords increase the risk of electric shock
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock..
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs,  alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
•  Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.  n accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety information for the angle grinder Safety Warnings common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting Off operations

• This power tool is intended to function as a grinder, sander, wire brush, or cut-off tool. Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
• Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
• Do not use accessories that are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
• The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
• The threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbor hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively, and may cause a loss of control.
• Do not use a damaged accessory. Before each use inspects the accessory such as abrasive wheels for chips and cracks, a backing pad for cracks, tear, or excess wear, and a wire brush for loose or cracked wires. If a power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
• Wear personal protective equipment. Depending on the application, use a face shield, safety goggles, or safety glasses. As appropriate, wear a dust mask, hearing protectors, gloves, and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high-intensity noise may cause hearing loss.
• Keep bystanders a safe distance away from the work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpieces or of a broken accessory may fly away and cause injury beyond the immediate area of operation.
• Hold the power tool by insulated gripping surfaces only when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
• Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
• Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
• Regularly clean the power tool’s air vents. The motor’s fan will draw dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
• Do not operate the power tool near flammable materials. Sparks could ignite these materials.
• Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush, or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on the direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

• Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use an auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces if proper precautions are taken.
• Never place your hand near the rotating accessory. The accessory may kick back over your hand.
• Do not position your body in the area where the power tool will move if kickback occurs. Kickback will propel the tool in a direction opposite to the wheel’s movement at the point of snagging.
• Use special care when working corners, sharp edges, etc. Avoid bouncing and snagging the accessory. Corners, sharp edges, or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
• Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickbacks and loss of control. Safety Warnings Specific for Grinding and Abrasive Cutting-Off operations
• Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
• The grinding surface of center-depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
• The guard must be securely attached to the power tool and positioned for maximum safety so that the least amount of wheel is exposed to the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with the wheel, and sparks that could ignite clothing.
• Wheels must be used only for recommended applications. For example: do not grind with the side of the cutoff wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
• A lways use undamaged wheel flanges that are of the correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
• Do not use worn-down wheels from larger power tools. The wheel intended for a larger power tool is not suitable for the higher speed of a smaller tool and may burst. Additional Safety Warnings Specific for Abrasive Cutting-Off operations
• Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
• Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
• When the wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
• Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kick back if the power tool is restarted in the workpiece. Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
• Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring, or objects that can cause kickback. Safety Warnings specific for Sanding operations
• Do not use excessively oversized sanding disc paper. Follow the manufacturer’s recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc, or kickback. Safety Warnings are specific for Wire Brushing operations
• Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and/or skin.
• If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to workload and centrifugal forces.

Additional safety information
Wear safety goggles.

• Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to an explosion. Penetrating a water line causes property damage or may cause electric shock.
• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working. Release the On/Off switch and set it to the off position when the power supply is interrupted, e. g., in case of a power failure or when the mains plug is pulled. This prevents uncontrolled restarting.
• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more securely than by hand.

Products sold in GB only:

Your product is fitted with a BS 1363/A approved electric plug with an internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into the main socket elsewhere.

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire, and/or serious injury. Please observe the illustrations at the beginning of this operating manual.

Intended use
The power tool is intended for cutting, roughing, and brushing metal and stone materials without the use of water.
A special protective guard for cutting must be used when cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting stone.
With approved abrasive tools, the power tool can be used for sanding with sanding discs.

Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Release lever for a protection guard
(2) Spindle lock button
(3) On/Off switch
(4) Auxiliary handle (insulated gripping surface)
(5) Grinder spindle
(6) Protection Guard for Grinding
(7) Mounting flange
(8) Grinding wheel
(9) Clamping nut
(10) Protection guard for cutting
(11) Cutting disc
(12) Handguard
(13) Rubber sanding plate
(14) Sanding sheet
(15) Round nut
(16) Cup brush
(17) Cutting guide with dust extraction protection guard
(18) Diamond-cutting disc
(19) Handle (insulated gripping surface)
(20) Securing device (only 3 603 CA2 0..)
(21) Direction-of-rotation arrow on the housing
A) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical Data

Article number| | 3 603 CA2 0..| 3 603 CA2 0..| 3 603 CA2 0..| 3 603 CA2 0..| 3 603 CA2 0..
---|---|---|---|---|---|---
Rated power input| W| 701| 701| 701| 701| 701
Rated speed| min-1| 11,000| 11,000| 11,000| 11,000| 11,000
Max. sanding disc diameter| mm| 115| 115| 115| 115| 125
Grinding spindle thread| | M 14| M 14| M 14| M 14| M 14
Max. grinding spindle thread length| mm| 21| 21| 21| 21| 21
Restart protection| | ●| ●| ●| ●| ●
---|---|---|---|---|---|---

Weight according to EPTA-Procedure 01:2014

– with an additional low-vibration auxiliary handle| kg| 1.7| 1.7| 1.7| 1.7| 1.7
---|---|---|---|---|---|---
– with standard auxiliary handle| kg| 1.7| 1.7| 1.7| 1.7| 1.7
Protection class| / II| / II| / II| / II| / II
---|---|---|---|---|---
Article number| | 3 603 CA2 4.| 3 603 CA2 4.| 3 603 CA2 4.| 3 603 CA2 4.
---|---|---|---|---|---
Rated power input| W| 730| 750| 750| 750
Rated speed| min-1| 12,000| 12,000| 12,000| 12,000
Max. grinding disc diameter| mm| 115| 115| 125| 125
Grinding spindle thread| | M 14| M 14| M 14| M 14
Max. thread length of grinding spindle| mm| 21| 21| 21| 21
Restarting Protection| | ●| ●| ●| ●

Weight according to EPTA‑Procedure 01:2014

3 603 CA2 7.
---|---|---|---|---|---
Rated power input| W| 780| 800| 850| 850
Rated speed| min-1| 12,000| 12,000| 12,000| 12,000
Max. grinding disc diameter| mm| 125| 125| 125| 125
Grinding spindle thread| | M 14| M 14| M 14| M 14
Max. grinding spindle thread length| mm| 21| 21| 21| 21
Restart protection| | ●| ●| ●| ●

Weight according to EPTA‑Procedure 01:2014

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information
PWS 700         PWS 7000        PWS 7-115 PWS 700-115 **PWS 700-125
Noise emission values are determined according to EN 60745-2-3**.
Typically the A-weighted noise level of the power tool is:

Total vibration values ah (triax vector sum) and uncertainty K determined according to EN 60745-2-3:

ah
K| m/s2
m/s2| 8.0
1.5| 8.0
1.5| 8.0
1.5| 8.0
1.5| 8.0
1.5
---|---|---|---|---|---|---

Grinding with abrasive disc:

ah
K| m/s2
m/s2| 5.5
1.5| 5.5
1.5| 5.5
1.5| 5.5
1.5| 5.5
1.5
---|---|---|---|---|---|---

The vibration level given in these instructions has been
measured in accordance with a standardized measuring procedure and may be used to compare power tools. It can also be used for a preliminary estimation of exposure to vibration.
The stated vibration level applies to the main applications of the power tool. However, if the power tool is used for different applications, with different application tools, or poorly maintained, the vibration level may differ. This can significantly increase the exposure to vibration over the total working period.
To estimate the exposure to vibration accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This can significantly reduce the exposure to vibration over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping the hands warm, and organizing workflows correctly.

Fitting
Fitting protective equipment

• Pull the plug out of the socket before carrying out any work on the power tool.
  Note: If the grinding disc breaks during operation or the holding fixtures on the protective guard/power tool become damaged, the power tool must be sent to the after-sales service immediately; see the “After-Sales Service and Application Service” section for addresses.

A protective guard for grinding

Place the protective guard (6) onto the holder on the power tool until the coding cams of the protective guard are aligned with the holder. When doing so, press and hold the unlocking lever (1). Press the protective guard (6) onto the spindle collar until the shoulder of the protective guard is sitting on the flange of the power tool and rotate the protective guard until it audibly clicks into place.
Adjust the position of the protective guard (6) to meet the requirements of the operation. To do this, push the unlocking lever (1) upward and rotate the protective guard (6) into the required position.

• Always position the protective guard (6) such that all three red cams on the unlocking lever (1) engage in the corresponding openings on the protective guard (6).
• Adjust the pr

Note: The coding cams on the protective guard (6) ensure that only a protective guard that is suitable for the power tool can be fitted.

A protective guard for cutting

• Always use the protective guard for cutting (10) when cutting bonded abrasives.
• Provide sufficient dust extraction when cutting stone. The protective guard for cutting (10) is fitted in the same way as the protective guard for grinding (6).

Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (17) is fitted in the same way as the protective guard for grinding (6). Side handle u Do not operate your power tool without the side handle (4). Screw the side handle (4) on the left or right of the machine head depending on how you are working.
Handguard

• Always fit the hand guard (12) when working with the rubber sanding plate (13) or with the cup brush/disc brush/flap disc. Attach the hand guard (12) to the side handle (4). Fitting the abrasive tools
• Pull the plug out of the socket before carrying out any work on the power tool.
• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working. Clean the grinding spindle (5) and all the parts to be fitted. Lock the grinding spindle with the spindle lock button (2) before clamping and releasing the abrasive tools.
• Do not press the spindle lock button while the grinding spindle is moving. The power tool may become damaged if you do this.

Grinding/Cutting Disc
Pay attention to the dimensions of the grinding tools. The mounting hole diameter must fit the mounting flange without play. Do not use reducers or adapters. When using diamond cutting discs, pay attention that the direction- of-rotation arrow on the diamond cutting disc and the direction of rotation of the machine (see direction-of-rotation arrow on the machine head) agree. See the graphics page for the mounting sequence. To fasten the grinding/cutting disc, screw on the clamping nut (9) and tighten with the two-hole spanner.

• After fitting the abrasive tool, check that the abrasive tool is fitted correctly and can turn freely before switching on the power tool. Make sure that the abrasive tool does not brush against the protective guard or other parts.

Flap disc

• Always fit the hand guard (12) when working with the flap disc.
  Rubber sanding pad

•  Always fit the hand guard (12) when working with the rubber sanding pad (13).
  See the graphics page for fitting instructions.
  Screw on the round nut (15) and tighten with the two-pin spanner.

Cup brush/disc brush

• Always fit the hand guard (12) when working with the cup brush or disc brush.
  See the graphics page for fitting instructions.
  The cup brush/disc brush must be screwed onto the grinding spindle until it rests firmly against the grinding spindle flange at the end of the grinding spindle thread.  Tighten the cup brush/disc brush with an open-ended spanner.

Approved abrasive tools
You can use all the abrasive tools mentioned in these operating instructions.
The permissible speed [min ] or the circumferential speed [m/s] of the abrasive tools used must at least match the values given in the table. It is therefore important to observe the permissible rotational/circumferential speed on the label of the abrasive tool.
-1

max. [mm]| |
---|---|---
D| b| d| -1[min]| [m/s]
115| 6| 22.2| 12000| 80
125| 6| 22.2| 12000| 80
115| –| –| 12000| 80
125| –| –| 12000| 80
75| 30| M 14| 12000| 45

| max. [mm]| |
---|---|---|---
| D| b| d| [min -1]| [m/s]
| 115| 6| 22.2| 12000| 80
| 125| 6| 22.2| 12000| 80
| 115| –| –| 12000| 80
| 125| –| –| 12000| 80
| 75| 30| M 14| 12000| 45

Rotating the Machine Head
Only for power tools with the article number 3 603 CA2 0..:

• Pull the plug out of the socket before carrying out any work on the power tool.
  The machine head can be turned by 180°. This allows you to set the On/Off switch to a more favorable handling position for special jobs, e. g., for left-handers.
  – Remove the screw at securing device (20) of the release lever (1) (see Fig. A).

– Completely unscrew the 4 screws (see Fig. B). Carefully turn the machine head to the new position without removing it from the housing. Mount and tighten the 4 screws again. – Screw the securing device (20) of the release lever (1) back onto the machine head (see Fig. C). Observe the instructions under “Fitting protective equipment”. The protection guard may only be turned while actuating the release lever (1).
Dust/Chip Extraction

The dust from materials such as lead paint, some types of wood, minerals, and metal can be harmful to human health. Touching or breathing in this dust can trigger allergic reactions and/or cause respiratory illnesses in the user or in people in the near vicinity.
Certain dust, such as oak or beech dust, are classified as carcinogenic, especially in conjunction with wood treatment additives (chromate, wood preservative). Materials containing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the material wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask. The regulations on the material being machined that apply in the country of use must be observed.

• Avoid dust accumulation at the workplace. Dust can easily ignite.

Operation

Start-up

• Pay attention to the mains voltage. The voltage of the power source must match the voltage specified on the rating plate of the power tool. Power tools marked with 230 V  can also be operated with 220 V.

When operating the power tool using a mobile generator that does not have sufficient reserve capacity or an adequate voltage control system with an inrush current boost converter, loss of performance or atypical behavior may occur upon switch-on.
Please check the suitability of the power generator you are using, particularly with regard to the mains voltage and frequency.

• Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Switching on/off
To start the power tool, push the on/off switch (3) forward.
To lock the on/off switch (3) in position, push the on/off switch (3) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (3); or, if the switch is locked, briefly push the on/off switch (3) backward and down and then release it.

• Always check abrasive tools before using them. The abrasive tool must be fitted properly and be able to move freely. Carry out a test run for at least one minute with no load.  Do not use abrasive tools that are damaged, run untrue, or vibrate during use. Damaged abrasive tools can burst apart and cause injuries.

Restart protection
The restart protection feature prevents the power tool from uncontrolled starting after the power supply to it has been interrupted.
To restart the tool, set the on/off switch (3) to the off position and then switch the power tool on again.
Working Advice

• Pull the plug out of the socket before carrying out any work on the power tool.

• Exercise caution when cutting slots in structural walls; see the “Information on structural design” section.

• Clamp the workpiece if it is not secure under its own weight.

• Do not load the power tool so heavily that it comes to a stop.

• If the power tool has been subjected to a heavy load, continue to run it at no-load for several minutes to cool down the accessory.

• Do not use the power tool with a cut-off stand.

• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.
  Rough grinding

• Never use cutting discs for rough grinding.
  The best rough grinding results are achieved with a set angle of 30° to 40°. Move the power tool back and forth with moderate pressure. This will ensure that the workpiece does not become too hot or discolored and that grooves are not formed.

Flap Disc
With the flap disc (accessory), curved surfaces and profiles can be worked. Flap discs have a considerably higher service life, lower noise levels, and lower sanding temperatures than conventional sanding sheets.
Cutting Metal

•   Always use the protective guard for cutting (10) when cutting bonded abrasives.
  When carrying out abrasive cutting, use a moderate feed that is suited to the material being machined. Do not exert pressure on the cutting disc and do not tilt or swing the
  power tool.
  Do not attempt to reduce the speed of a cutting disc coming to a stop by applying pressure from the side.

The power tool must always work in an up-grinding motion. Otherwise, there is a risk that it will be pushed uncontrolled out of the cut. For best results when cutting profiles and rectangular tubing, start at the smallest cross- section.

Cutting stone

• Provide sufficient dust extraction when cutting stone.
• Wear a dust mask.
• The power tool may be used only for dry cutting/grinding.
  For best results when cutting stones, use a diamond cutting disc.
  When using the extraction guard for cutting with a guide block (17), the vacuum cleaner must be approved for vacuuming stone dust. Suitable vacuum cleaners are available from Bosch.

Switch on the power tool and position it with the front part of the guide block on the workpiece. Move the power tool with a moderate feed motion that is suited to the material being machined.
When cutting especially hard materials such as concrete with a high pebble content, the diamond cutting disc can overheat and become damaged as a result. This is clearly indicated by circular sparking, rotating with the diamond cutting disc. If this happens, stop cutting and allow the diamond-cutting disc to cool down by running the power tool for a short time at maximum speed with no load. Working noticeably slower and with circular sparking indicate that the diamond-cutting disc has become dull. You can resharpen the disc by briefly cutting it into abrasive material (e.g. lime-sand brick).

Information on structural design
Slots in load-bearing walls are subject to DIN 1053 part 1 or country-specific regulations. These regulations must be observed under all circumstances. Seek advice from the responsible structural engineer, architect, or construction supervisor before starting work.

Maintenance and Service

Maintenance and Cleaning

• Pull the plug out of the socket before carrying out any work on the power tool.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean. In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service center that is authorized to repair Bosch power tools.
  Store and handle the accessories carefully.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning the maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Australia, New Zealand, and the Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com
Armenia, Azerbaijan, Georgia
Robert Bosch Ltd.
David Agmashenebeli ave. 61
0102 Tbilisi, Georgia
Tel. +995322510073
www.bosch.com
Kyrgyzstan, Mongolia, Tajikistan, Turkmenistan, Uzbekistan
TOO “Robert Bosch” Power Tools, After Sales Service
Muratbaev Ave., 180
050012, Almaty, Kazakhstan
Service Email: service.pt.ka@bosch.com
Official Website: www.bosch.com, www.bosch- pt.com
Disposal
The power tool, accessories, and packaging should be recycled in an environmentally friendly manner.
Do not dispose of power tools along with the household waste.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its implementation into national law, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

|
---|---

EU Declaration of Conformity
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards. Technical file at * Angle grinder Article number

PWS 700
PWS 7000
PWS 7-115
PWS 700-115
PWS 700-125
PWS 730-115
PWS 750-115
PWS 750-125
PWS 7500
PWS 780-125
PWS 8000
PWS 850-125
PWS 8500-125| 3 603 CA2 0..
3 603 CA2 0..
3 603 CA2 0..
3 603 CA2 0..
3 603 CA2 0..
3 603 CA2 4..
3 603 CA2 4..
3 603 CA2 4..
3 603 CA2 4..
3 603 CA2 7..
3 603 CA2 7..
3 603 CA2 7..
3 603 CA2 7..| 2006/42/EC
2014/30/EU
2011/65/EU| EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:2013+
A11:2014+A12:2014+A13:2015
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012

• Robert Bosch Power Tools GmbH
  (PT/ECS)
  70538 Stuttgart
  GERMANY
  ---|---|---|---
  Henk Becker
  Chairman of Executive
  Management| Helmut Heinzelmann
  Head of Product Certification
  ---|---

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 09.09.2019

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
1 609 92A 5NX (2020.03) O / 15

References

• Invented for life | Bosch Global
• dz.com
• ハナノヒ 365days | 季節の花が毎月届くサブスクリプション – ハナノヒ 365days | 季節の花が毎月届くサブスクリプション｜日比谷花壇
• 巧米网为您服务！(QiaoMi.com)
• CONTACT US
• Skånevik Ølen Kraftlag AS
• Inicio | Bosch en Argentina
• Bosch Elektrowerkzeuge | Bosch Elektrowerkzeuge
• Bosch Power Tools | Bosch Power Tools
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Bosch Power Tools | Bosch Power Tools
• Bosch Elektrowerkzeuge | Bosch Elektrowerkzeuge
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Elettroutensili Bosch | Elettroutensili Bosch
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
• Inicio | Bosch en Chile
• Invented for life | Bosch Global
• Contato | Bosch no Brasil
• Inicio | Bosch en Peru
• boschherramientas.com.ec
• Herramientas eléctricas de Bosch | Bosch Professional
• herramientasbosch.net

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>