pasapair SF713A Infrared Patio Heater User Manual

pasapair SF713A Infrared Patio Heater

Product Information

Technical Specification

• Product model: SF713A
• Rated voltage/frequency/power: 120V / 60Hz / 1500W (one carbon fiber quartz heating tube)
• Heating range: Second gear heating – H gear / L gear
• Timing gear: 1-24H
• Safety protection: Tipping power failure protection, overheating power failure protection
• Flame: Control by remote control
• Remote control distance: 8 m / 315 inch
• Waterproof Rating: IP55
• Optimal Operating Environment: Humidity < 85%

When using electrical appliances, basic safety precautions should always be followed including the following:
READ ALL INSTRUCTIONS BEFORE USE AND KEEP THESE INSTRUCTIONS

1. Read all instructions before using this heater.

2. Do not use this heater outdoors.

3. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.

4. Do not run the power cord under carpeting.
   Do not cover the power cord with throw rugs, runners, or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.

5. To disconnect the heater, turn controls to off, then remove the plug from the outlet.

6. Connect to properly grounded outlet only. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).

7. To prevent a possible fire, do not block operate the firebox on soft surfaces, like a bed, where openings may become blocked.

8. There is a thermostat limiter inside the heater. When the inner temperature overheat or abnormal heating occurs, the thermostat protective device cuts off the power supply to avoid fireplace from damaged or risk of fire.

9. Use the heater only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.

10. WARNING: Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.

WARNING: There is no user serviceable parts inside fireplace/heater. If the unit appears to malfunction, turn the unit off and unplug from the wall immediately and contact Customer Service.

• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving thos heater. Keep combustible material, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3ft (0.9m) from the front of the heater and keep them away from the side or rear.

• Extreme caution is necessary when any heater is used by or near children
  or invalids and whenever the heater is left operating and unattended.

• Always unplug the heater when not in use.

• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.

• Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric shock or fire, or damage to the heater.

• A heater has hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.

CAUTION: While the heater is in use, the top center of the fireplace can get hot to the touch, and may cause serious injury or burns. Always supervise children around the fireplace/heater. Do not place any cloth or decorations over the heater outlet or fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury.

Model No.: 050-HA-61001
This device complies with Part 15 of the FCC Rules.

FCC Warning

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Read this instruction manual prior to assembly to familiarize yourself with the various steps. Lay out all components and hardware separately on a flat surface and make sure that no parts are missing or damaged before assembly. Do not destroy or discard any packaging until you are certain that you have all the necessary parts for assembly. Hand tight all hard wares and careful not to over tighten to avoid damaging the product.

CAUTION

• There are small components used in the construction of this product.
• Loose items should be kept away from pets and children to avoid a choking hazard.
• Keep all plastic bags and packaging film away from pets and children to avoid suffocation.

Package Contents

• Heater x 1
• Machine Bracket x 1
• ST3.9*30 Screw x 4
• Plastic Tube x 4+2
• M4*10 Screw x 4
• M5 Allen Key Wrench x 1
• M6 Allen Key Wrench x 1
• Open End Wrench x 1
• Plastic screw (gypsum board) x 4+2
• Wall Mounting Bracket x 1
• Remote Control x 1
• M5x16 Screws x 4

Product Notice

1. Mute, Fast heat : The machine operates quietly without wind and provides 2 seconds fast heating. It has two heating gears (H gear, L gear) and a 24-hour timing option.
2. Security protection: The machine has tipping power failure protection and overheating power failure protection. Tipping power outage protection —- When the machine tilts more than 30° in any direction, the anti-tipping protection function will start and the heating will stop, and the display will blink “EE”; When the machine is put right, it will automatically resume heating. Abnormal overheat protection —- When the machine is working abnormally overheat, the temperature controller in the machine will automatically power o ff and stop heating; After that, it is necessary to manually restart the main switch on the machine or insert and remove the plug before heating again, so as to avoid frequent automatic heating when overheating.
3. All-weather waterproof: The body is made of cold-rolled steel plate material with flame-retardant engineering plastic on both sides. It is resistant to UV aging. The heating area has stainless steel screen protection isolation. The machine has an IP55 waterproof design and can withstand rain, splashing water, and sand particle intrusion from any direction.

Product Usage Instructions

Assembling
Option  1 ( Wall mounting)

1. Place the machine bracket on the back of the heater and lock it with 4 screws.

2. Drill holes on the wall according to the four holes on the wall mounting bracket, ensuring that the holes are more than 2 meters away from the ground.

3. Nail the plastic tubes into the drilled holes on the wall:

   • For brick walls or cement walls, drill 8mm holes and nail plastic tubes.
   • For gypsum board walls, drill 9mm holes and tighten the screws.

Install the wall mounting bracket
Attach the wall board to the wall with four screws, Make sure the bracket is leveled.

Install the heater
Align the four screw holes of the heater bracket on the back of the machine with the screw holes of the wall mounting bracket, screw in four screws respectively, and then tighten the screws with the allen key wrench , and then the host machine is fixed on the wall.

Adjust the machine Angle
After the machine is installed on the wall, the pitch Angle of the machine, it can be adjusted to the most suitable heating position.

• The back of the fuselage has a wall hanging connection bracket.
• When installing the heater on a wall, the unit should be at least 6 ft (approx 1. 8m) above the ground to ensure safety.
• Make sure there is no curtains, clothes, towels, or any combustible materials within 3 ft (approx 1m) of the heating zone of the unit.

USER INSTRUCTION

Before use

• Check that the air intake and exhaust is not covered or obstructed in anyway.
• Keep combustible objects at least 3 ft (0.9 m) away from the unit.
• Plug the unit to a grounded power socket.

Grounding

• This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.

CAUTION / WARNING

• Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
• DO NOT modify the plug provided with the product nor using any bypass device if the plug does not fit the outlet. Have a proper outlet installed by a qualified electrician

USER INSTRUCTION (CONTROL PANEL)

Press the switch in the transparent cover on the right side of the machine to the position of “I”, then the machine will display “–” standby mode.

CONTROL PANEL

• Function key: This key has multiple functions, press this key to turn on heating (default H gear) – Press again for L gear — Press again to turn off, so the cycle.
• Timing key: 24-hour working time can be set, which is displayed as: 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H, 9H, 10H, 11H, 12H, 13H, 14H, 15H,
  16H, 17H, 18H, 19H, 20H, 21H, 22H, 23H, 24H, and so on.

Heater Control
Press the power button / heat button to enable the heat function. “High Heat” is selected by default. Continue pressing the heat button to cycle through the heat setting.

NOTE: Flame effect will automatically enable once the heat function is turned on. Use the remote control to control flame effect

• Timer Control
  • Press the timer control button to turn the timer on.
  • Continue pressing the timer control button to cycle through the timer setting.
• Timer interval includes: 0H,1H,2H, 3Н,4, 5Н,6Н,7H, 8H, 9H, 10Н, 11Н,12Н, 13Н, 14H, 15H, 16H, 17H, 18H, 19H,20H,21H,22H,23H,24H.

USER INSTRUCTION (REMOTE CONTROL)

Remote Control
The operation of the remote control buttons work the same as the button on the control panel. The remote control distance is 6ft from the front and 4ft from the sides of the unit.

Power Button
Press power button to turn on the unit. Press the power button again to turn off the unit.

Heater Button
Press the heater button to enable the heat function.

Flame Button
Press the flame button on the remote control to disable the flame function.

Timer Control Button
Press the timer control button to cycle through the timer setting.

Time Adjustment Increase / Decrease
Press the increase or decrease button to select different time setting.

Install / Replace Battery
The remote control is provided with 1.5V AAA batteries.

1. Press and slide off the back cover from the remote control.
2. Insert 1.5V AAA batteries into the battery compartment and make sure to install batteries in the correct polarity.
3. The negative end of the battery should be install against the spring inside the battery compartment.

CAUTION / WARNING

• Dispose old / used battery at a suitable recycling point or according to local regulations.
• DO NOT ingest battery. If accidentally swallowed, seek for medical help immediately.

Manufacturer: Zhongshan Sunshine Electrical Appliance Tech Co., Ltd.
Add.: No.2, Yongyi Road 3, Heng lan Town, Zhongshan City Guangdong, China Contact: Joyce
Email: info@pasapairhome.com

Installation

1. Attach the wall mounting bracket to the wall using four screws, ensuring that the bracket is leveled.
2. Align the four screw holes of the heater bracket on the back of the machine with the screw holes of the wall mounting bracket.
3. Screw in four screws respectively and tighten them with the allen key wrench to fix the host machine on the wall.

Adjustment
After the machine is installed on the wall, adjust the pitch angle of the machine to the most suitable heating position.

FAQ

1. Q: What is the power supply of the electric heater?
   A: The power supply is 120V-60Hz.

2. Q: What is the heating range of the heater?
   A: The heater has two heating gears – H gear and L gear.

3. Q: Does the heater have a timing option?
   A: Yes, the heater has a 1-24 hour timing option.

4. Q: What safety protections does the heater have?
   A: The heater has tipping power failure protection and overheating power failure protection.

5. Q: Can the heater be controlled remotely?
   A: Yes, the heater can be controlled by a remote control with a distance of 8 meters (315 inches).

6. Q: Is the heater waterproof?
   A: Yes, the heater has an IP55 waterproof rating and can withstand rain, splashing water, and sand particle intrusion from any direction.

7. Q: What is the optimal operating environment for the heater?
   A: The optimal operating environment for the heater is humidity below 85%.

WARRANTY

• Thank you for choosing PASAPAIR product. We sincerely hope that you are satisfied with it. The manufacturer’s warranty covers the product for a period of 12 months from the date of purchase against manufacturing faults. All warranties are automatically kept track of in our system, so there is no need to register your product.
• Agent/Distributor is welcome to contact us.
• Email: info@pasapairhome.com.
• Any help or questions during use, please contact us via website www.pasapairhome.com, send email to info@pasapairhome.com, , we will service you within 24 hours. We suggest to provide a warranty card, a photo or a video if there’s broken spare part or not working machine so that we can be much more clear about your problems and offer you the best solution.

Please fill in the table and email it within 10 days from the date of purchase.

References

• PASAPAIR

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>