Pasapair B0CXCTLCLF Electric Patio Heater with Tripod Stand APP Control Instruction Manual

Pasapair B0CXCTLCLF Electric Patio Heater with Tripod Stand APP Control

• Model: QHA-15W
• Power Supply: AC 120V~60Hz 1500W

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING THE APPLIANCE

IMPORTANT SAFETY INSTRUCTIONS

Warning: To avoid the risk of electric shock, always make sure the appliance is unplugged from the socket before relocating, servicing or cleaning it. When using electrical appliance, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.
2. Use the appliance in a well-ventilated area. The heater got hot when in use. To avoid burns, do not touch your bare skin on the hot surface of the appliance. If needed, use the handle when moving the heater. Keep combustible material, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from all sides of the heater.
3. Do not leave the appliance unattended while it is in use. Always unplug the heater when not in use.
4. Extreme caution is necessary when any heater is used by or near children or invalids. The heater is not intended for use by children.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, or has been dropped or damaged in any manner. Please discard or return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or re-pair.
6. To disconnect the appliance from the socket, turn the switch off and then remove the plug from the socket. Pull directly on the plug. Do not pull on the power cord.
7. Do not insert or allow objects to enter the ventilation or exhaust openings as this may result in electric shock, fire or product damage.
8. To avoid the risk of fire, do not block the air intake or exhaust in any manner. Do not use on a soft surface, such as a bed, where openings may become blocked.
9. The appliance has no internal electrical arcing or sparking parts. Do not use it in areas where gasoline, paint or other flammable liquids are used or stored due to the risk of fire and explosion.
10. Use the heater only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock, or personal injury.
11. The heater is not intended for use in bathrooms, laundry areas, and similar moist indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
12. Do not allow the power cord to hang down(e.g. over the edge of a table or counter)place/run the power cord under rugs, carpeting or in high-traffic areas where it may be tripped over or pulled.
13. If heater may include an audible or visual alarm to warn that parts of the heater are getting excessively hot. If the alarm sounds (or illuminates), immediately turn the heater off and inspect for any objects on or adjacent to the heater that may have blocked the airflow or otherwise caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING (OR ILLUMINATING).
14. SAVE THESE INSTRUCTIONS”
15. INSTALL BOTTOM OF HEATER NOT LESS THAN 1800 mm or 70.9 inch ABOVE

THE FINISHED FLOOR and INSTALLER LA PARTIE INFÉRIEURE DU RADIATEUR AU MOINS À 1800 mm or 70.9 inch AU-DESSUS DU PLANCHER FINI. 16)Grounding Instructions: This heater is for use on 120 volts. The cord has a plug as shown at (A) in figure below. An adaptor as shown in (C) is available for connecting three- blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box. The adaptor should not be used if a three-slot grounded receptacle is available.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help The device must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm or 7.9inch from nearby persons.

TECHNICAL SPECIFICATION

INSTALLATION INSTRUCTIONS

Installation Notes:

• This heater must be installed by a qualified electrician.
• Before and during installation, always ensure that the heater is disconnected from the power supply and is cool.
• The heater can be installed horizontally or vertically.
• During installation, please ensure that the heater is a minimum of 1.8 metre or 70.9 inch above the ground so that it cannot be directly touched during operation.
• When installing horizontally or to a ceiling, do not place the heater at an angle of more than 90 degrees, or below 45 degrees. If the heater installation angle is vertical or close to vertical, make sure the power cord is always under the heater.
• During the use of the heater, there is a certain increase in the temperature of the heater body. Make sure that the power cord never touches the heater body and is away from the heater housing.
• Do not install heaters on the surface of any flammable materials.
• Make sure that the heater is always at least 0.5m or 19.7 inch wide from the ceiling and adjacent walls.
• If you are using the heater outdoors be sure to use a weatherproof qualified outlet.
• Make sure that there are no wires or water pipes in the area where the heater is going to be installed before you begin drilling.
• The heater must be installed on the mounting bracket provided by the manufacturer (see Figure A below)
• Remove the expansion rubber and screws from the accessory bag, drill four holes with a diameter of 8mm/0.3inch on the wall. The hole depth is 70mm or 2.7inch, the hole distance is 32mm or 1.3inch, (300mm≤L≤450mm or 11.8inch≤L≤17.7inch) install the expansion rubber in the fitting in the hole, and then mount the wall bracket from the accessories. Remove it and fix it to the wall with a 560 mm or 0.22.4inch screw.
• Place the wall bracket on the corresponding screw on the back of the heater, and then adjust the wall bracket to the proper position with the nut from the accessory bag, then lock it to ensure it will not loosen
• Lock the wall bracket mounted on the back of the heater and the wall, adjust the heater to a suitable position, and lock the lock with the nut and screw from the accessory sleeve to ensure that it will not loosen

Wall hanging diagram

OPERATION GUIDE

1. On/Off button
2. Gear mode button
3. Down
4. Timer button
5. Child Lock button
6. Up button
7. wifi reset key
8. Display button

Operating Instructions:

Check before turning on the appliance.

1. Check if the power cord is in good condition.
2. Plug the heater power cord into a standard electrical socket. The product adopts a 120V AC power supply. Before use, please confirm if the power sockets match the voltage and current of the body nameplate.

Start the Machine.
Plug the unit into a grounded 120V outlet, the power light on, and press the ” ” button of the remote controller to start.

Temperature Settings

Gear mode

1. Press ” (!)” to enter the gear setting mode, and the screen is blinking.
2. Press the ” A “or” *” button to set the power gear
3. Firt gear: 30% power
4. Second gear: Half power
5. Third gear: 80% power
6. Fourth: Full power

“Timer Function

1. Press the “ ” button to enter the timing setting state.
2. Select a shutdown time by using the “UP” or “DOWN” buttons. The timing indicator is light on when the timer is running.”

“Child Lock Function

1. Long press “ ” for three seconds to open the child lock mode
2. Repeat the above actions and long press UP” &”DOWN for three seconds to close the child lock mode

Reset the Wi-Fi

1. Long press” ” for three seconds to activate the WiFi reset mode Display Control
2. Press “ ” to extinguish the screen, and press any key to wake up

Display Control

1. Press “ ” to extinguish the screen, and press any key to wake up

FAULT DESCRIPTION AND REPAIR

E5 fault: The tipping switch function is triggered and the machine needs to be righted.

WIFI CONNECT AND OPERATION WIFI

Scan the QR Code below with your smartphone or search it in the APP Store or Google Play to download the “QZsmart” app.

PREPARATION BEFORE USE

1. Make sure your heater is on and ensure that your smart phone is connected to 2.4 GHz Wi-Fi network.
   NOTE: This device works only on 2.4 GHz Wi-Fi® network.

2. Ensure that the Bluetooth function of the mobile phone is enabled at the same time; otherwise, the device cannot be automatically searched.

3. Download the QZsmart app from the App Store or Google Play™.
   NOTE: Authorize the app to access network and location services.

4. If you are using the app for the first time, click the “Sign up” button and register. If you already have an account, click the “Log in” button.

Connect method 1:

Connect method 2

OPERATION GUIDE

Note: Due to continued updates, the images in this manual may vary slightly from the latest procedure. All images in this manual are for reference purposes only

CLEANING AND MAINTENANCE

1. If the inside of the heater or the heating element is covered with dust or dirt, please have it cleaned by a qualified service provider. Do not operate the heater in this situation.
2. Disconnect the heater from the power supply. Do not clean before cooling to avoid burns!
3. The only thing that needs to be cleaned is the exterior surface of the heater.
4. Do not use strong abrasives or solvent cleaners when cleaning the heater as they may damage the plastic parts. Wipe the outside of the heater with a wrung and damp cloth.
5. When not in use, remove it from the mounting position and store the heater carefully in a safe, dry place out of reach of children. If the heater will not be in use for a long period, especially in humid or high-salinity areas, please clean, dry, and store it in safe packaging.
6. Do not touch the heating element with your fingers as the residue from your hands can affect the lifetime of the heating element. If you accidentally touch it, remove the marks with a soft damp cloth.
7. Do not attempt to repair or adjust any electrical or mechanical functions on this heater The heater does not contain user-serviceable parts and must be returned to the retailer if damaged or defective.

WARRANTY

Thank you for choosing the PASAPAIR product. We sincerely hope that you are satisfied with it. The manufacturer’s warranty covers the product for 12 months from the date of purchase against manufacturing faults. All warranties are automatically kept track of in our system, so there is no need to register your product. Agent/Distributor is welcome to contact us. Email:info@pasapairhome.com. Any help or questions during use, please contact us via the website www.pasapairhome.com, or send an email to info@pasapairhome.com, we will service you within 24 hours. We suggest providing a warranty card, a photo or a video if there’s a broken spare part or no working machine so that we can be much more clear about your problems and offer you the best solution.

Warranty Card

• Email:
• Buyer’s name:
• Address:
• Tel:
• Order Number:
• Purchase date:
• Item name:
• Model:
• Serial No.:

Please fill in the table and email it within 10 days from the date of purchase.

References

• PASAPAIR

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>