MATTEL HTP54 Hot Wheels Rodger Dodger Rc Vehicle Instruction Manual

MATTEL HTP54 Hot Wheels Rodger Dodger Rc Vehicle

Product Information

• Model:
  • HTP54-MA70_I/S_21A
• Size:
  • 22 x 22.5
• Specifications
  • Flyer Sheet required: 24S_RC_R0000-MA70_21A_Battery_Flyer_G2 EU DoC (for Europe)
  • Age: 4+

Product Usage Instructions

• Battery Installation
  • Unscrew the battery cover with a Phillips head screwdriver (not included).
  • Install 2 AA (LR6) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries.
  • Replace the battery cover and tighten the screw.
  • Replace batteries in the remote controller if the LED on the remote controller does not go on during playing or if the vehicle does not respond well after a recharge.
• Charge the Vehicle
  • The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged before first use.
  • Slide the power switch to OFF (0/).
  • Open the charge cord cover.
  • Connect the charge cord to a 5V/1A USB power adapter (not included).
  • Charging will begin when the cord is connected. A red LED on the vehicle will be on as the vehicle is charging.
  • The LED will turn green but remain on for a while when the vehicle is fully charged. Unplug the charge cord when charging is complete. A full charge will usually take approximately 120 minutes. Charging time may vary.
  • Close the charge cord cover.
  • Recharge the vehicle if the vehicle begins to run slowly or does not respond.
• Frequently Asked Questions (FAQ)
  • Q: What type of batteries does the vehicle use?
  • A: The vehicle uses 2 AA (LR6) 1.5V alkaline batteries.
  • Q: How long does it take to fully charge the vehicle?
  • A: A full charge usually takes approximately 120 minutes, but charging time may vary.
  • Q: What should I do if the LED on the remote controller does not turn on during playing?
  • A: Replace the batteries in the remote controller.
  • Q: What should I do if the vehicle does not respond well after a recharge?
  • A: Replace the batteries in the remote controller and recharge the vehicle.

CONTENTS

FEATURES

• A. LED INDICATOR
• B. DRIVING CONTROLS
• C. BOOST BUTTON
• D. BATTERY BOX
• E. STEERING ALIGNMENT
• F. CHARGE CORD COVER
• G.  POWER SWITCH
• H. LED INDICATOR
• I. CHARGE CORD

SET UP

REMOTE CONTROLLER BATTERY INSTALLATION

1. Unscrew the battery cover with a Phillips head screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries.
3. Replace the battery cover and tighten the screw.
4. Replace batteries in the remote controller if the LED on the remote controller does not go on during playing or if the vehicle does not respond well after a recharge.

CHARGING THE VEHICLE

The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged before first use.

1. Slide the power switch to OFF (  ).
2. Open the charge cord cover.
3. Connect the charge cord to a 5V/1A USB power adapter (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will be on as the vehicle is charging.
5. The LED will turn green but remain on for a while when the vehicle is fully charged. Unplug the charge cord when charging is complete. A full charge will usually take approximately 120 minutes. Charging time may vary.
6. Close the charge cord cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
   • NOTE: The power switch must be in the OFF ( ) position when charging the vehicle.
   • Red
   • Vehicle is charging
   • Green
   • The vehicle is fully charged

TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before recharging the vehicle.

PAIRING THE REMOTE CONTROLLER AND VEHICLE

1. Slide the power switch to ON (I) on the vehicle.
2. Push the remote controller’s driving control joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on the remote controller.
   • NOTE: If the vehicle does not respond to the remote controller after pairing, switch the vehicle off then back on to try pairing again or replace the batteries in the remote controller if the batteries are drained.
   • Pairing
   • Pairing is complete

TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To resume normal play, slide the vehicle’s power switch to OFF then ON again, and then push the remote controller’s driving control joystick forward/backward to pair the vehicle and remote controller.

STEERING ALIGNMENT

1. Check the vehicle’s steering alignment before playing by driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left, turn the steering adjuster dial to the opposite direction and adjust until it runs in a straight line.

HOW TO DRIVE

CHECKLIST

• Is the vehicle fully charged?
• Is the remote controller equipped with fresh batteries?
• Is the remote controller paired with the vehicle?
• Has the vehicle’s steering been aligned?

CONTROLS

• SKILL CHECK! Remember, steering directions are flipped on the remote controller when you are driving backward!
• NOTE: The operating  range of the remote controller is up to 30 m (98 ft).

SPEED BOOST

• Press the boost button for extra speed!
• HVIN: HTP54R ( ), HTP54T ( )

CONTACT

• ©2023 Mattel. ® and ™ designate U.S. trademarks of Mattel, except as noted.
• https://faleconosco.mattel.com.br/Contato.
• E-mail: sac.matteldobrazil@mattel.com.
• Flyer Sheet required: 24S_RC_R0000-MA70_21A_Battery_Flyer_G2 EU DoC (for Europe)

References

• Les Jouets Mattel France - Bienvenue sur Les Jouets Mattel
• MATTEL & FISHER-PRICE CUSTOMER SERVICE
• Mattel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>