CIGAR OASIS Oasis Caliber IV Digital Hygrometer Thermometer User Manual
- June 17, 2024
- CIGAR OASIS
Table of Contents
CIGAR OASIS Oasis Caliber IV Digital Hygrometer Thermometer
Specifications
- Product: Oasis CaliberTM IV Digital Hygrometer/Thermometer
- Features: Humidity Reading, Temperature Reading, Set, Max/Min/Clear, Fahrenheit/Celsius, Battery Tray, Magnetic Mount
Product Usage Instructions
Getting Started
- Slide the battery tray out to insert the battery with the plus side up to activate the display.
- Mount the unit in a central area with unblocked airflow. Clean the surface before attaching the magnet mount.
Switching Between Celsius & Fahrenheit
Move the Fahrenheit/Celsius Switch back and forth to toggle between temperature readings in Fahrenheit and Celsius.
MAX/MIN Recording & Display
- To view maximum values, press MAX/MIN/Clear button once.
- To view minimum values, press twice. Reset values by holding the button for about 5 seconds.
Calibrating the Humidity Display
- Determine the calibration needed by finding the difference between the display and the expected value.
- Press and hold the Set button for 3 seconds to enter calibration mode.
- Adjust the display using the Min/Max/Clear button within the +/-6% range.
FAQ
- Q: How often should I calibrate my hygrometer?
- A: Factory-calibrated hygrometers may not need frequent recalibration. Perform calibration only if you notice significant discrepancies in readings.
- Q: Can I replace the battery without losing previous data?
- A: Replacing the battery will reset the minimum and maximum values recorded by the hygrometer.
Thank you for purchasing the Oasis Caliber™ IV digital hygrometer and thermometer. We are certain that you will find this is the most dependable and accurate unit available in the consumer market. To maintain your hygrometer in optimal working order, we recommend that you review this manual thoroughly to understand how to use the advanced features of the Oasis Caliber™ IV.
OVERVIEW
- Humidity Reading
- Temperature Reading
- Set
- Max/Min/Clear
- Fahrenheit/Celsius
- Battery Tray
- Magnetic Mount
Getting Started
- Slide the battery tray out to insert the battery plus side up. This will activate the display and begin the collection of readings.
- Mount the unit onto the desired location. The best location is in a central area where the airflow to the unit will not be blocked. To attach the magnet mount, first ensure that the surface is clean of any dust or other debris. For best results, use alcohol to clean the area where the adhesive will be applied. Remove the backing paper from the adhesive disc on the back of the magnet and apply pressure to hold the magnet in place for 30 seconds.
Switching Between Celsius & Fahrenheit
To switch the display between Fahrenheit and Celsius temperature readings,
move the Fahrenheit/Celsius Switch back and forth.
MAX/MIN Recording & Display
The Oasis Caliber™ IV will record the minimum and maximum values for both
humidity and temperature. To view the maximum values, press the MAX/MIN/Clear
button one time. The maximum value will be displayed with the word MAX at the
top of the temperature reading.
To view the minimum values, press the MAX/MIN/Clear button two times. The
minimum value will be displayed with the word MIN at the top of the
temperature reading.
To reset the values, while viewing either the MAX or MIN value, press and hold
the MAX/MIN/Clear button for about 5 seconds. When the display shows empty
values, that MAX or MIN value has been reset. Both values reset independently.
Removing or replacing the battery will also reset both the minimum and maximum
values.
Calibrating the Humidity Display
Your hygrometer is factory-calibrated and should not need any further adjustments. The following instructions should be performed only to correct a calibration error.
- Determine the amount of calibration needed by finding the difference between the display value and the expected value. For example, if you are expecting 70% but your unit displays 71%, the calibration difference is 71-70 = 1. If you need the display lower as in this example, change the calibration by -1%. If you need the display higher, add (+) to the value.
- Press and hold the Set button for 3 seconds to place the unit into calibration mode.
- In calibration mode, you will see the current adjustment setting flashing on the display. If this is the first time you are calibrating your unit, it will show 0%. If you have already calibrated the unit previously, you will see the current adjustment.
- Press the Min/Max/Clear button to adjust the display based on your calibration. Pressing the button once will change the adjustment by 1%. The Oasis Caliber™ IV adjustment range is +/-6% in the sequence: 0, +1, +2, +3, +4, +5, +6, -6, -5, -4, -3, -2, -1, 0.
- When you have completed your adjustment, press the Set button one more time and it will take the unit out of calibration mode. If you leave the unit in calibration mode for more than one minute without pressing any buttons, the unit will automatically will change back to operations mode.
Restoring Factory Calibration
To restore your Oasis Caliber IV to factory calibration, simply follow the
calibration instructions above and adjust the display back to 0%. This will
restore the unit to factory calibration.
Limited Warranty
The Oasis Caliber™ IV is covered by a limited warranty against defects from materials or workmanship for a full 1 Year with proof of purchase. Any misuse or excessive wear and tear is not covered under the limited warranty.
Error Codes
- When the humidity or temperature is too low or high for an accurate reading the following codes will display:
- LL% – below 32° F
- HH% – above 122° F
Contact Information
- If you have any questions or warranty inquiries please call us directly at 516-520-5258 or email customersupport@cigaroasis.com.
- 79 Heisser Court
- Farmingdale, NY 11735
- www.cigaroasis.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>