Chroma-Q Inspire XT Mini RGBW LED House Light User Guide
- June 17, 2024
- Chroma-Q
Table of Contents
Chroma-Q Inspire XT Mini RGBW LED House Light
Product Information
Specifications
- Models: 632-8220, 632-8221, 632-1500, 632-1600, 632-1700, 632-2500, 632-2600, 632-2700, 632-6500, 632-6505, 632-8200
- Software Version (Engine): XT 4.0, Mini / Reg 2.2
- Part Numbers: CHINHLRGBWXT, CHINHLRGBWXTW, CHINHLRGBW32E,
CHINHLRGBW42E, CHINHLRGBW65E, CHINHLW32E, CHINHLW42E, CHINHLW65E,
CHINMINIHLRGBWT, CHINMINIHLRGBWTW
Product Usage Instructions
Safety
- This product is intended for professional use only and should not be used domestically or outdoors.
- The bright flash of light during power-up and continuous strobe effect may cause epileptic seizures.
- Always use the product with a safety cable.
FAQ
- Q: Can this product be used outdoors?
- A: No, this product is not intended for outdoor use and should only be used professionally.
- Q: What type of cable should be used for DMX & data wires?
- A: For DMX & data wires, it is recommended to use Belden 9729 or CAT5e/6 cables. The maximum cable distance from DATA OUT to the first fixture must not exceed 152m/500 ft.
For a full product manual please visit www.chroma-q.com
- Part Number: CHINHLRGBWXT, CHINHLRGBWXTW,
- CHINHLRGBW32E, CHINHLRGBW42E, CHINHLRGBW65E, CHINHLW32E, CHINHLW42E, CHINHLW65E,
- CHINMINIHLRGBWT, CHINMINIHLRGBWTW
- Model: 632-8220, 632-8221,
- 632-1500, 632-1600, 632-1700, 632-2500, 632-2600, 632-2700,
- 632-6500, 632-6505, 632-8200
- Software Version (Engine) XT 4.0, Mini / Reg 2.2
Overview
The Chroma-Q® Inspire™ Terminal Strip LED house light features a single light engine with high-powered LEDs (RGBW), a fully homogenized optic, and is controlled via the Inspire™ External Control Box. Through the Inspire™ External Control Box, the fixture can be controlled remotely through the ANSI E1.11 USITT DMX 512-A protocol.
Safety
-
This product is for professional use only. It is NOT intended for domestic or outdoor use.
-
The bright flash of light during power-up and continuous strobe effect may cause epileptic seizures.
Caution -
This product must be used with a safety cable.
- To connect the wiring for power and control data:
- The power input connector box (figure 3) is supplied with the fixture and is not attached. It must be mounted as described in the following steps
- Insert the power cable with the appropriate ½” NPT connector or cable strain relief through the connector box (Figure 3). The hole on the connector box has a suitable dimension to attach a ½” NPT connector on it. The Power Input Terminal Block Plug has three soft wires attached to it. Attach the provided wires to the wiring for the AC power input with quick connectors or Marret connectors (Figure 3). ½” NPT connector, cable strain relief, quick connectors, or Marret connectors are not included with the fixture.
- Put the quick / Marret connectors inside the connector box. Plug the wired terminal block plug into the power input terminal block header (Figure 4).
- Connect the DMX control data cables from the Inspire™ External Control Box / another Inspire™ Light Fixture to the terminal block plug. Ensure that the bare wire is not visible. Some insulation of the wire must be inside the hole. The maximum strip length is 4 mm (Figure 5). Plug the terminal block plug into the terminal block headers at the rear of the fixture (Figure 2 & 5).
- Put the connector box in place and fasten the connector box with a capacitive screw.
Notes
- IMPORTANT: Termination resistors (supplied with the External Control Box) are REQUIRED on the first fixture in each data run (Figure 5) – see user manuals for more details.
- For DMX & data wires use Belden 9729 or CAT5e/6.
- Max. cable distance from DATA OUT to the first fixture must not exceed 152m/500 ft.
- Emergency power is shown as an example only and may not be used on all projects.
Mounting
- A mounting bracket is built into the enclosure for overhead applications.
- Secure the fixture with a safety bond.
- A fixing hold is built into the enclosure.
- Optional accessories are also available for mounting Inspire™ light fixtures.
Optics
- The Inspire XT™ is provided with a lens that delivers a beam angle of approximately 32°. Using a lens from the included Spread Lens kit will increase the beam to approximately 42° or 65°. For lens installation details, consult the instructions included in the kit.
- The Inspire™ Terminal Strip can be built with either narrow, medium, or wide lenses. The beam angles are: Narrow: ~32°; Medium: ~42°; Wide: ~65°.
- The Inspire Mini™ Terminal Strip is built with a wide lens with a beam angle of approximately ~65°.
- The optional Spreader Lens kit is available for changing the beam angle of any Inspire™ Light Fixture.
Control
The control functions are accessed through the touchscreen display at the
front panel of the Inspire™ External Control Box. The features of the
touchscreen display are shown in Figure 8.
Further Information
Please refer to the Chroma-Q® InspireTM manual for more detailed information. A copy of the manual can be found at the Chroma-Q® website – www.chroma-q.com/support/downloads.
Approvals & Disclaimer
The information contained herein is offered in good faith and is believed to
be accurate. However, because the conditions and methods of use of our
products are beyond our control, this information should not be used in
substitution for customer tests to ensure that Chroma-Q® products are safe,
effective, and fully satisfactory for the intended end use. Suggestions of use
shall not be taken as inducements to infringe any patent. Chroma-Q® sole
warranty is that the product will meet the Chroma-Q® sales specifications in
effect at the time of shipment. Your exclusive remedy for breach of such
warranty is limited to the refund of purchase price or replacement of any
product shown to be other than as warranted.
Chroma-Q® reserves the right to change or make alterations to devices and
their functionality without notice due to ongoing research and development.
The Chroma-Q® InspireTM has been designed specifically for the lighting
industry. Regular maintenance should be performed to ensure that the products
perform well in the entertainment environment.
If you experience any difficulties with any Chroma-Q® products please contact
your selling dealer. If your selling dealer is unable to help, please contact
support@chroma-q.com. If the selling dealer is
unable to satisfy your servicing needs, please contact the following for full
factory service:
CONTACT
Outside North America
- Tel: +44 (0)1494 446000
- Fax: +44 (0)1494 461024
- support@chroma-q.com.
North America
- Tel: +1 416-255-9494
- Fax: +1 416-255-3514
- support@chroma-q.com.
For further information please visit the Chroma-Q® website at
www.chroma-q.com.
Chroma-Q® is a trademark, for more information on this visit
www.chroma-q.com/trademarks.
The rights and ownership of all trademarks are recognized
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>