6100 Mineral Pool Care Cycler

Product Information

Specifications

• Product Name: Mineral Pool-Care Cycler

• For Pools up to: 25,000 Gallons

• Main Features: Kills bacteria, helps maintain pH, reduces
  chlorine use, prefilled pacs

• Components: Pool FROG Cycler, Pool FROG Mineral Reservoir, FROG
  BAM, Pool FROG Bac Pac

Product Usage Instructions

Installation Tips

Follow the installation tips provided in the manual to ensure
proper performance of the Pool FROG System. Choose the appropriate
installation method based on your pool setup.

Step-by-Step Guide

Step 1: Preparing the Pool

Before installing the system, ensure your pool is clean and
balanced. Follow the guidelines provided in the manual for optimal
results.

Step 2: Putting the System to Work

Install the Pool FROG Cycler and Mineral Reservoir according to
the instructions. Ensure proper placement and connections for
effective water treatment.

Step 3: Setting the Control Dial

Adjust the control dial on the Cycler based on your pool size
and water conditions. Refer to the manual for recommended
settings.

Step 4: Routine Pool Care

Regularly check the system for proper functioning. Monitor
chlorine levels and adjust settings as needed to maintain a healthy
pool environment.

Maintenance

Refer to the maintenance section in the manual for instructions
on replacing O-rings and knobs to ensure smooth operation of the
Pool FROG System.

Winterizing

Follow the winterizing guidelines provided to protect your
system during colder months and prevent damage.

Troubleshooting

If you encounter any issues with the system, refer to the
troubleshooting section in the manual for common problems and
solutions.

FAQ

Q: Can I use the Pool FROG System in hot tubs?

A: The Pool FROG System is suitable for pools and hot tubs.
Follow the instructions provided for proper usage in hot tubs.

Q: How often should I replace the Pool FROG Mineral

Reservoir?

A: The Mineral Reservoir should be replaced as recommended in
the manual or when indicated by the system for continued
effectiveness.

Pool FROG® 6100 Instruction Manual
Mineral Pool-Care Cycler for Pools up to 25,000 Gallons
Cleaner
because it kills bacteria two ways
Clearer
because it helps keep pH in range
Softer
because it reduces chlorine use up to 50%*
Easier
with prefilled pacs for no mess, no guess and no stress
Pool FROG Cycler comes with the Pool FROG Mineral Reservoir
Patented Mineral Disinfectant
Customer Service 800-222-0169 frogproducts.com
WARNING
To minimize the risk of serious injury, death or damage, before installing or first using this equipment, read Instruction Manual and all safety labels and follow all safety instructions and precautions. Save manual for future reference. Ver la versión en español de este manual en frogproducts.com/product/pool-frog-model-6100
1

TABLE OF CONTENTS

Pool FROG Introduction

3

Notes and Safety Information

4

Safety Labels on Cycler

5

Installation Tips to Ensure Proper Performance

6

Filter Installation with Nipple Kit and Flex Hose

7

Filter Installation with Flex Hose Only

8

Hard-Plumbed Installation

9

Step 1: Preparing the Pool

10

Step 2: Putting the System to Work

11

Step 3: Setting the Control Dial

12

Step 4: Routine Pool Care

13

Replacing Pool FROG Mineral Reservoir

14

Using FROG® BAM®

15

Using Pool FROG Bac Pac®

16

Winterizing

17

Troubleshooting

18

Parts List

19

Maintenance – Replacing Control Dial O-Rings

20

Maintenance – Replacing Cap O-Rings and Knobs

21

For information on King Technology’s entire product line, visit our website at frogproducts.com

2

Welcome to easier pool care courtesy of FROG®. With Pool FROG, your pool water will look and feel better without a lot of work or a lot of chlorine. This system controls bacteria using a combination of minerals and reduced chlorine levels­up to 50%* less.

There are 4 parts to the Pool FROG System: 1. Model 6100 Pool FROG Cycler 2. Pool FROG Mineral Reservoir 3. FROG BAM 90-day Algae Preventative 4. Pool FROG Bac Pac

Part 1 Pool FROG Cycler
The water treatment center that controls the flow of water to each part of the Pool FROG System.

Part 2 Pool FROG Mineral Reservoir
Holds the minerals and fits inside the Pool FROG Cycler. Product # 01-12-6112

For Pools up to 25,000 gallons. Product # 01-01-6180

MMOSEITNUEVRHEAESEARRTSFIPAOYSBTOLNESESOR,RIHRXLWEOEOSMFHPRNREOILTRECOAENHVGPCRTOEOEH.IVDORSELR

Part 3
FROG BAM
Use with the Pool FROG Cycler for a 90-Day Algae-Protection Guarantee. One bottle is good for 15,000 gallons. Product # 01-10-5060

Part 4 Pool FROG Bac Pac
Prefilled with chlorine tablets and fits inside the Pool FROG Mineral Reservoir. Product # 01-03-5880

Pool FROG Mineral Reservoir comes inside Pool FROG Cycler and is also sold separately. Pool FROG Bac Pac and FROG BAM also sold separately.
FROG Mineral System consists of the FROG minerals silver chloride and carbonate used in conjunction with 0.5 ppm chlorine. The FROG Mineral Reservoir must be used in conjunction with the FROG Bac Pac (EPA Reg. No.: 53735-2), an EPA registered chlorine pool product or a chlorine delivery device. *Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.
For pools and hot tubs 3

Notes and Safety Information

General Notes
These instructions contain information for the safe and proper operation of this Cycler. Observe the following principles:
· Ensure that everyone using this Cycler follows the instructions and safety precautions.
· Keep the instructions nearby and available for reference throughout the service life of this Cycler.

These instructions do not provide for every possible contingency that might be encountered in connection with installation, operation or maintenance of this equipment. Should further information be desired or should particular issues arise which are not covered sufficiently in this manual, contact King Technology at 800-222-0169.

Explanation of the signal words
Signal words, which depict the probability and severity of harm, are used in these instructions. They are defined as follows:

Signal Word
DANGER WARNING
NOTICE

Meaning
Indicates an imminently hazardous situation which, if not avoided, will result in death, serious injury or major property damage. Indicates a hazardous situation which, if not avoided, could result in serious injury, death, or major property damage.
Indicates special instructions that are important but not related to physical injury hazards.

Explanation of the safety pictographs
The following pictographs illustrate the type of hazard. Pictograph Type of Danger Safety Alert/General Hazard Explosion Risk Hazardous Pressure Flammable Fire Hazard

Identification of warnings
Warnings are intended to help you recognize risks and avoid death, injury or property damage. This is how warnings are identified:
Signal Word
Pictographs Description of danger. Consequences if ignored. The arrow signals a safety precaution to be taken to
eliminate or reduce the risk.

4

Safety Label on Cycler
Review this label before installing or operating this Cycler. Contact King Technology at 800-222-0169 if this label is missing from your Pool FROG Cycler.
Fire, explosion and high pressure hazards To minimize the risk of serious injury, death or property damage while using the Pool FROG Cycler:
Read, understand and follow all instructions and safety precautions in the manual, and on this Cycler and on any label for chemicals used with this Cycler including Pool FROG Bac Pacs, Pool FROG Mineral Reservoir and FROG BAM Algae Preventative.
DANGER
Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the Pool FROG Cycler. Never mix Trichlor chlorine tablets with Calcium Hypochlorite, or with any other form of concentrated chlorine or other chemicals. Never add any other types of chlorine or shock treatments through the skimmer. These products should be added directly
into the pool if required. Do not contaminate the Pool FROG Cycler, Pool FROG Mineral Reservoir, Pool FROG Bac Pac or FROG BAM with dirt, organic
matter, pool chemicals (such as calcium hypochlorite or pool shocks), fertilizers or other household chemicals. Contact between any of these substances and the Pool FROG Cycler, Pool FROG Mineral Reservoir, Pool FROG Bac Pac or FROG BAM, will result in a chemical reaction with the generation of heat, liberation of hazardous gasses and fire or explosion.
WARNING
Use only Pool FROG Bac Pacs, Pool FROG Mineral Reservoir, and FROG BAM in the Pool FROG Cycler. Never use bulk chemicals. To prevent the build up of gas pressure in the Pool FROG Cycler, be sure the pool return line valves are open ­
except when opening or servicing the unit. Do not inhale fumes from the Pool FROG Cycler or Pool FROG Bac Pac. Avoid sparks, smoking, or any open flame near Pool FROG Cycler or chemicals. Do not exceed maximum operating pressure of 50 psi or maximum temperature of 104º F. Do not remove the cap while under pressure. Always turn off pump and bleed off pressure before opening Pool FROG Cycler. Do not install automatic or fast shut off valves downstream of Cycler. Always install the Pool FROG Cycler AFTER a heater (if applicable) on the return line. Always install any additional sanitizing equipment AFTER and NEVER BEFORE the Pool FROG Cycler is installed on the return line. Do not permit children to use or climb on this product. This product must be positioned to prevent children from using it as a means of access to the pool. Always stand clear of the Pool FROG Cycler during pump start-up. Replace Pool FROG Cycler if you see signs of cracks, damage or degradation to the Cycler body or cap.
NOTICE
Prior to pressurizing, check with your dealer to ensure your plumbing connections meet building codes. Failure to properly winterize your Pool FROG Cycler could result in freeze damage. (See page 17 for winterizing details.)
5

Installation Tips to Ensure Proper Performance

Before installing, read all directions carefully and contact your dealer for installation support.

WARNING
· Do not exceed maximum operating pressure of 50 psi.
· Do not install automatic or fast shut off valves downstream of Pool FROG Cycler.
· Always install the Pool FROG Cycler AFTER the heater (if applicable) on the return line.
· Always install any additional sanitizing equipment AFTER and NEVER BEFORE the Pool FROG Cycler is installed on the return line.

A. With High Flow Rate (greater than 80 gpm) Pool FROG Cycler
Install T-fittings exactly as shown.

1. If using a multi-speed pump, run pump for at least 6 hours per day at high speed (at least 40 gpm).
   If the pump will run on low speed 24 hours per day or less than 6 hours per day on high speed, you must bleed the air while the pump is on by unscrewing the back knob until water appears. Then screw the knob back in. Repeat this process each time the cap is removed for any reason.

2. Install Cycler with 4-8 psi back pressure.

Lower back pressures could result in under

chlorination. Change the eyeball fittings in

the return jets to a smaller size to increase

back pressure. Contact King Technology at

800-222-0169 for a specially designed

Cycler pressure gauge to determine back

pressure at pool start-up.

PN #01-22-4000

3. Special installation Requirements:

IMPORTANT: Over chlorination or damage to the Pool FROG Cycler or other equipment could result if special installations A, B or C are not used in these situations.

· If water flow is higher than 80 gallons per minute (gpm), see diagram A.
· If an in-floor cleaner is included with pool, see diagram B, with two options. Preferred installation is Option 1 with two separate lines.
· If set-up is a pool and spa combination with common equipment, see diagram C.

B. With In-Floor Cleaner – TWO OPTIONS
OPTION 1- A Two-Line Installation
The best option is to have two lines. One line with pump, filter, heater and Pool FROG Cycler and a second line with a separate pump for the in-floor cleaning system (filter optional).

Line 1 Line 2

Pool FROG Cycler

PUMP

FILTER

HEATER

PUMP

FILTER

POOL RETURN
POOL WATER LEVEL
IN-FLOOR CLEANER VALVE

POOL WATER LEVEL

OPTION 2 – A 3-Way Valve Installation
3-way manual valve or 3-way motor valve plus controls Pool FROG Cycler

IN-FLOOR CLEANER VALVE

PUMP

FILTER

POOL WATER LEVEL

C. Pool and Spillover Spa Combination

Questions? Call Customer Service at 800-222-0169 Monday thru Friday, 8 am to 5 p.m. central time.
6

Pool FROG Cycler

Install

TOOLS NEEDED Screwdriver
Pipe Wrench
INCLUDED WITH Pool FROG Cycler Pipe Thread Tape or Sealant

Installation with Nipple Kit and Flex Hose

1. Apply pipe thread tape or sealant to each threaded end of nipple.

4. Apply pipe thread tape or sealant to threaded end of hose adapter.

2. Screw one end of nipple into the filter return. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN.
Sand Filter

5. Screw adapter into the other side of Pool FROG Cycler. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN.
6. Attach return section of hose to the adapter with clamp. Tighten clamp with screwdriver.

One 6″ X 1½” TBE PVC Nipple
MATERIALS NEEDED One Hose Adapter 1½” X 1½” X 1¼”
One Section of 1½” or 1¼” Flex Hose

DE and Cartridge Filter

3. Screw either side of Pool FROG Cycler on to open nipple end until upright and secure.
Sand Filter

7. To prevent damage to heaters or filters, see your dealer about installing a corrosion resistant check valve which will reduce the back flow of chlorine gas when the Pool FROG Cycler is turned off.
Sand Filter

One Hose Clamp

RECOMMENDED
4-8 psi Back Pressure
To avoid over or under chlorination, replace eyeball fittings in the return jets to a smaller or larger size to adjust back pressure. For best results use King Technology’s pressure gauge, order Part No. 01-22-4000.

For DE and Cartridge lters you may have to tip the lter back when screwing the Cycler onto the nipple.
DE and Cartridge Filter

PUMP

DE and Cartridge Filter

HOSE CHECK CLAMP VALVE
TO POOL

1 1/2″ OR 1 1/4″

FLEX HOSE

HOSE

ADAPTER

NIPPLE

PUMP
7

TOOLS NEEDED Screwdriver
Pipe Wrench
MATERIALS NEEDED Pipe Thread Tape or Sealant
Two hose adapters 1½” X 1½” X 1¼”
Two Sections of 1½” or 1¼” Flex Hose (one provided with filter)
Two Hose Clamps
RECOMMENDED 4-8 psi Back Pressure To avoid over or under chlorination, replace eyeball fittings in the return jets to a smaller or larger size to adjust back pressure. For best results use King Technology’s pressure gauge, order Part No. 01-22-4000.

Installation with Flex Hose Only
The Pool FROG Cycler should always be installed between the filter and pool (or between heater and pool if applicable). Never install Pool FROG Cycler before the heater or damage to the heater could occur.

1. Apply pipe thread tape or sealant to the threaded end of both hose adapters.
2. Screw adapters into each end of Pool FROG Cycler. Hand tighten. Finish tightening by turning 1 to 2 revolutions with pipe wrench. DO NOT OVER TIGHTEN.

4. To prevent damage to heaters or filters, install a corrosion resistant check valve which will reduce the back flow of chlorine gas when the system is turned off.

Sand Filter

HOSE CLAMP

1 1/2″ X 1 1/2″ X 1 1/4″ HOSE ADAPTER

1 1/2″ OR 1 1/4″ FLEX HOSE

PUMP

TO POOL

HOSE CLAMP

HOSE CLAMP

FILTER

HOSE ADAPTER

HOSE ADAPTER

CHECK VALVE

DE and Cartridge Filter

FILTER

TO POOL

HOSE CLAMP

HOSE CLAMP

1 1/2″ OR 1 1/4″ FLEX HOSE

HOSE
ADAPTERS CHECK VALVE

PUMP

3. Attach the filter section of flex hose to one hose adapter and the return section of flex hose to the other hose adapter with clamps and tighten with screwdriver. Bi-flow valve design allows water flow installation in either direction.

5. For better stability, Pool FROG Cycler may be mounted on a treated wood base using Phillips pan head screws, one in front and two in back. If you have questions about stability, please contact your dealer or King Technology.

8

Install

TOOLS NEEDED Pipe Wrench

Hard-Plumbed Installation

Hacksaw

Tape Measure
MATERIALS NEEDED
Pipe Thread Tape or Sealant, Primer and PVC Cement

Primer

PVC Cement

1½” Male Adapter (slip x MPT)
or 2″ Female Adapter (slip x FPT)

The Pool FROG Cycler should always be installed between the filter and pool (or between heater and pool if applicable). Never install Pool FROG Cycler before the heater or damage to the heater could occur.

Do NOT install in copper pipe if using Pool FROG Bac Pac as chemical corrosion may lead to pipe failure.

OR

Do NOT install Pool

Bi-flow valve design allows

12″

FROG Cycler off-line. installation in either flow

direction.

Allow a minimum 12″ of 12″ above and
on each side of Pool FROG Cycler to ensure room for easy replacement of Pool FROG Mineral
12″
Reservoir and Pool FROG Bac Pac.

1. 2. Screw adapters into each end of Pool FROG Cycler following directions for a male adapter or a female adapter. Hand tighten. Finish tightening

Measure the distance between

by turning 1 to 2 revolutions with a pipe wrench.

the outside adapters

DO NOT OVER TIGHTEN.

and cut out a section

of pipe 3″ less than

that dimension.

SECURE CYCLER

1a.
If using male adapters, apply pipe thread tape or sealant to the threaded end of each adapter.

1b.
If using female adapters, apply pipe thread tape or sealant to the threaded end of each cycler port.

For better stability, Pool FROG Cycler may be mounted on a treated wood base using Phillips pan head screws, one in front and two in back. If you have questions about stability, please contact your dealer or King Technology.

Primer

PVC Cement

Following Primer directions, brush Primer on the inside of the adapters and to ends of pipe. Repeat this process with PVC cement following manufacturer’s directions on that product.

Insert PVC pipe into adapters with a twisting action. Hold in place 5 to 10 seconds to bond.

To prevent damage to heaters

or filters, see your dealer about

installing a corrosion resistant

check valve which will reduce the

back flow of chlorine gas when the

Cycler is turned off. 9

Step 1: Preparing the Pool

Make sure the pool has adequate circulation. The total volume of pool

For best results in achieving water balance, follow steps 5a through 5e in order.

water must completely circulate

through the pump and filter at least

1 to 2 times per day. This usually requires 8 to 12 hours of circulation. Check with your dealer for the proper circulation time for your pool.

5a. Take a water sample
from the pool and dip a FROG Test Strip into it.

Check the pool’s filter gauge often

and periodically clean filter per the

manufacturer’s directions. A dirty

filter will slow the flow of water which

could hamper proper circulation.

WARNING
Do not exceed maximum operating pressure of 50 psi.

3. Check the Water Hardness of your fill water before adding to the pool. If calcium content is higher than 400 ppm, find a soft water source to fill your pool instead; otherwise water balance will be very difficult.

Check for metals in the pool such as iron or copper. Before attempting water balance,

these should be removed. See your dealer

for a metal out or sequesterant and follow

the label directions carefully.

5. Before beginning with any pool care program, you must first balance your pool water. Take a water sample to your local pool professional (or use a complete test kit) to test for the important Water Balance Guidelines.
IMPORTANT: Always follow printed instructions on the balancing chemical packages. Add balancing chemicals in small increments one at a time with circulation running. For best results, wait 8-12 hours before testing again and adding any additional balancing chemicals.

5b. Look at the Total Alkalinity reading first. Adjustments
should be made to bring the Total Alkalinity in the range of 80 ­ 120 ppm prior to making any adjustments to pH even if it throws pH off further.

Total Alkalinity

0

40

(ppm)

Alcalinidad Total

(mg/L)

VERY LOW

LOW

MUY BAJO BAJO

80 120 180 240

IDEAL

HIGH

VERY HIGH

ALTO

MUY ALTO

5c. After Total Alkalinity is in range, test for pH. It should be
between 7.2 and 7.8. If higher or lower, add a pH adjuster.

6.2 6.8 7.2 7.8 8.4 pH

VERY LOW

LOW

MUY BAJO BAJO

IDEAL

HIGH

ALTO

5d. Then test your Water Hardness again. If lower than 200
ppm, add Calcium Increaser. Always maintain 200-400 ppm.

5e. Lastly test for stabilizer or conditioner levels. Add
conditioner if the level is below 20 ppm. This will prevent chlorine burn off. If stabilizer level is above 80 ppm, partially drain water and re-fill.

Initially shock the pool with a chlorine shock only to rid the water of contaminants

and establish a chlorine residual. Always

follow the manufacturer’s directions

carefully. See the DANGER box below for

important guidance on shocking.

Water Balance Guidelines

pH:

7.2 ­ 7.8

Total Alkalinity:

80 ­ 120 ppm

Hardness:

200 ­ 400

Total Dissolved Solids:

<1500

Stabilizer:

20 ­ 80 ppm

Free Chlorine:

0.5 ­ 1.0 ppm

10

DANGER
· Never add any other types of chlorine or shock treatments through the skimmer. These products should be added directly into the pool if required.
· Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the Pool FROG Cycler.

Operate

Step 2: Putting the System to Work

Install a Pool FROG Mineral

Reservoir into the Pool FROG

Cycler. (See page 14 for

directions.)

IMPORTANT: Replace the Pool FROG Mineral Reservoir every 6 months or after one pool season, whichever is shorter. After that time, you will hear the spent media inside, however it is no longer effective and must be replaced.

Insert FROG BAM into the open center of the Pool FROG Mineral Reservoir in the Pool FROG Cycler. (See page 15 for directions.)
Use FROG BAM for a 90-day
Algae Protection Guarantee!

Replace cap and run Pool FROG

Cycler, with Pool FROG Mineral

Reservoir inserted, for 10 minutes

on Setting 10.

When chlorine reading is down to 1.0 ppm, which may take a few days, insert Pool FROG Bac Pac into the open center of the Pool FROG Mineral Reservoir. (See page 16 for directions.)

11

Step 3: Setting the Control Dial

1. This Cycler is designed to work effectively with a variety of pool equipment as long as the following procedures are followed.
Set the control dial by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See #2 below for adjusting directions. IMPORTANT: If using a multi-speed pump, pump-run times of at least 6 hours per day at high speed are recommended for proper performance.
If running the pump at low speed only or on high speed less than 6 hours, please follow the 24 hour low-speed directions below.

POOL SIZE
Gallons Diameter
7,000 (18′) 9,000 (21′) 12,000 (24′) 15,000 20,000 25,000

1/2 hp 5.0 5.5 6.0 NR NR NR

8 HOUR PUMP RUN TIME

PUMP SIZE

3/4 hp

1 hp

4.5

4.0

5.0

4.5

5.5

5.0

6.0

5.5

NR

6.0

NR

6.5

SINGLE-SPEED PUMP OR HIGH-SPEED PUMP RUN TIME

12 HOUR PUMP RUN TIME

1 ½ hp

PUMP SIZE

1/2 hp 3/4 hp

1 hp

1 ½ hp 1/2 hp

3.5

4.5

4.0

3.0

5.0^

3.5

4.0

5.0

4.5

4.0

5.5^

4.0

4.5

5.5

5.0

4.5

4.0

4.5

5.0

6.0

5.5

5.0

4.5

5.0

5.5

NR

6.0

5.5

5.0

5.5

6.0

NR

6.5

6.0

5.5

6.0

24 HOUR PUMP RUN TIME

PUMP SIZE 3/4 hp 1 hp

3.0

2.5

3.5

3.0

4.0

3.5

4.5

4.0

5.0

4.5

5.5

5.0

1 ½ hp 4.0^ 4.5^ 5.0^ 3.5 4.0 4.5

^ ­ Bypass installation recommended. See “Installation Tips” on page 6. NR ­ This pump size is not recommended for this size pool. RECOMMENDED FLOW RATE: 20-60 gpm

24 HOUR, LOW-SPEED PUMP-RUN TIME In order to ensure proper performance when running the pump on low speed for 24 hours per day or high speed less than 6 hours per day, bleed the air while the pump is on by unscrewing the knob on the back of the Cycler near the cap until water appears. Then screw the knob back on. Repeat this process each time the cap is removed for any reason. Set the control dial at 6 and follow the adjustment directions below to determine the correct setting for your pool.

EXAMPLE

POOL SIZE
Gallons Diameter
7,000 (18′) 9,000 (21′) 12,000 (24′) 15,000 20,000 25,000

1/2 hp 4.5 5.0 5.5 6.0 NR NR

12 HOUR PUMP RUN TIME

PUMP SIZE

3/4 hp

1 hp

4.0

3.0

4.5

4.0

5.0

4.5

5.5

5.0

6.0

5.5

6.5

6.0

1 ½ hp
5.0^ 5.5^ 4.0 4.5 5.0 5.5

Find your starting dial setting by matching up the parameters of your pool on the above chart. An above ground pool with approximately 12,000 gallons, with a 1 horsepower pump running 12 hours a day, would require a starting setting of 4.5.

For the first week, test the pool water

daily for free chlorine with FROG Test

Strips to ensure correct dial setting.

Continue to test weekly throughout

the season.

IMPORTANT: Control dial settings in excess of these recommendations could result in excess trichlor levels being discharged into the pool. This can result in bleaching or discoloration of areas around the pool inlet or, in some cases, bleaching or discoloration of the entire pool liner or paint. In addition, excess trichlor in the pool can create health hazards to bathers.
12

After each testing, adjust the dial up by 1/2 increment if the free chlorine reading has dropped below 0.5 ppm or adjust down by 1/2 increment if the reading has risen above 1.0 ppm. Continue this process each day until the free chlorine reading stabilizes to at least 0.5 ppm.
Remember to adjust dial by 1/2 increments only in order to prevent over chlorination which may bleach pool surfaces.

Operate

Step 4: Routine Pool Care

Run filtration enough hours to

circulate all water 1 to 2 times per

Shock the pool every other week or as needed. We recommend a

day. More than that could result in

non-chlorine shock as reducing

over chlorination.

chlorine use is the goal of FROG

products. However, using a chlorine

shock is OK too.

WARNING
To prevent the build up of gas pressure in the Pool FROG Cycler, be sure the pool return line valves are open ­except when opening or servicing the unit.

Regularly test water with FROG Test

Strips to maintain pH and Total

Alkalinity.

NOTE: Water balance is affected by bather load, chemical usage, evaporation and the makeup of source water, so maintaining water balance regularly is important.

DANGER
· Never add any other types of chlorine or shock treatments through the skimmer. These products should be added directly into the pool if required.
· Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the Pool FROG Cycler.
5.
Before closing the pool for winter, use FROG BAM following the directions on page 15.

Maintain 0.5 to 1.0 ppm free chlorine level at all times.

Note: These lower chlorine levels are only acceptable when using FROG minerals.
6.

Remember to replace Pool FROG Mineral Reservoir and all other Pool FROG replacements as directed.

DANGER
Do not contaminate the Pool FROG Cycler, Pool FROG Mineral Reservoir, Pool FROG Bac Pac or FROG BAM with dirt, organic matter, pool chemicals (such as calcium hypochlorite or pool shocks), fertilizers or other household chemicals. Contact between any of these substances and the Pool FROG Cycler, Pool FROG Mineral Reservoir, Pool FROG Bac Pac or FROG BAM, will result in a chemical reaction with the generation of heat, liberation of hazardous gasses and fire or explosion.
13

Replacing a Pool FROG Mineral Reservoir
Must be replaced every 6 months or after one pool season.

Serial No.

Series 6100 (01-12-6112) FOR POOLS UP TO 25,000 GALLONS

Product Description: The POOL FROG Mineral Reservoir is the heart of an advanced pool care system that destroys bacteria. The patented mineral formula in the POOL FROG Mineral Reservoir also neutralizes acids, which helps keep the pH in an acceptable range with less monitoring. The controlled release of minerals provides an optimum level of protection in your pool. The FROG Mineral System+ reduces chlorine use up to 50%*. Simply use with at least 0.5 ppm of an EPA registered source of chlorine such as the POOL FROG Bac Pac (EPA Reg. No. 53735-2) or a chlorine delivery device. Using the POOL FROG

Check the top of the box and back label of product to make sure you have the correct Pool FROG Mineral Reservoir to fit your Pool FROG Cycler.
IMPORTANT: The Pool FROG Mineral Reservoir must be replaced every 6 months or after one pool season, whichever is shorter.

2. IMPORTANT: Remove and read the information card.
Please note: Complete instructions for inserting a Pool FROG Mineral Reservoir, FROG BAM and Pool FROG Bac Pac are included inside the Pool FROG Mineral Reservoir.

DANGER · Never use fast dissolving chlorine tablets,
liquid bleach, or calcium hypochlorite in the Pool FROG Cycler.
3.
Turn off pump and turn control dial to Setting 0. This reduces the flow of water into the unit when the cap is open.

14

Open Pool FROG

Cycler cap.

5. Remove the Pool FROG Bac Pac and if not empty, set to the side or store for winter. Then remove the Pool FROG Mineral Reservoir and discard if it has been used for one pool season or 6 months, whichever is shorter.

Find slot on side of Pool

SLOT IN POOL FROG Mineral Reservoir FROG MINERAL and line up with fin

RESERVOIR

inside the Pool FROG

Cycler. Lower Pool

FIN INSIDE OF FROG Mineral Reservoir POOL FROG into Pool FROG Cycler

CYCLER

until secure.

Replace the Pool FROG Bac Pac inside the Pool FROG Mineral Reservoir to continue operating system (see directions on page 16)

Mark your calendar ahead for the six month replacement

of the Pool FROG Mineral

Reservoir. Once wetted,

the time-released mineral

coating of this product

is effective up to 6

consecutive months or one

pool season, whichever is

shorter. After that time you

will hear the spent media

inside, however, it is no

longer effective and must

be replaced.

Using FROG BAM for an Algae-Protection Guarantee

If you are not using FROG BAM, refer to page 16 for Using the Pool FROG Bac Pac. See FROG BAM product labeling for complete directions for use (EPA Reg. No. 53735-9).

For a preventive dose add: ·One FROG BAM for pools up to 15,000 gallons. ·Two FROG BAM for pools between 15,000 and 30,000 gallons.

NOTE: If using directly after a shock treatment, test the water rst to ensure the pH is in the proper range of 7.2-7.8 and the chlorine level is no more than 4.0 ppm. Avoid using other chemicals until this product has been circulated ( ltered) for at least 24 hours.

DANGER

Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the Pool FROG Cycler.

Important: If storing FROG BAM prior to use, always keep in a cool, dry place away from children and pets.

Turn pump on for 90 minutes allowing FROG BAM to circulate through pool.

Operate

Remove cap from FROG BAM

without removing seal.

To remove expended FROG BAM

Turn off pump. Turn control dial to 0. Open Cycler cap. Stand

bottle, turn pump off and turn dial to Setting 0.

back to let any chlorine fumes

dissipate.

Insert upside down into the

open center of the Pool FROG

Mineral Reservoir pushing down

firmly on FROG BAM bottle

allowing key in Pool FROG Cycler to puncture seal.

Remove Pool FROG Cycler cap.

Looking

down at top

of bottle

seal

Lift FROG BAM up and allow any water in the container to

drain through the Pool FROG

Cycler before discarding in trash

3. Replace cap by hand only.

or offering for recycling. Do not reuse or refill this container.

DO NOT OVER TIGHTEN.

NOTE: If water shows more than

a hint of blue inside Pool FROG

Cycler, replace the Pool FROG

Cycler cap, turn dial to Setting

10 and run the pump for one

minute.

Turn control dial on to

Setting 10.

8a. If pool size requires additional FROG BAM, repeat steps 1-8.

8b. When water is clear in the Pool FROG Cycler, insert a Pool FROG Bac Pac according to the instructions on page 16.
15

Using the Pool FROG Bac Pac

Pool FROG Bac Pac is required

to assure up to 50% reduction in

chlorine use*. Pool FROG Bac Pac

sold separately.

(EPA Reg. No. 53735-2)

DANGER
Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the Pool FROG Cycler.

WARNING
Avoid sparks, smoking, or any open flame near Pool FROG Cycler or chemicals.

IMPORTANT: Read the label on the Pool FROG Bac Pac carefully

before using.

1. 2. Colored Caps

Turn pump off. Turn control dial to 0.

Remove cap from Pool

FROG Cycler and stand

back to let any chlorine

fumes dissipate.

Remove colored caps by grabbing on to the lip of one cap with a pliers and pulling up until cap releases. Repeat the process for the other cap.
7.

Invert Pool FROG Bac Pac and

shake slightly until chlorine

tablets fall into tower areas.

16

Line up the small leg of the Pool FROG Bac Pac with the small opening in the Pool FROG Mineral Reservoir and the large leg with the large opening. Lower Pool FROG Bac Pac into Pool FROG Mineral Reservoir until secure.
Top View
Replace cap by hand only. DO NOT OVER TIGHTEN.
The chlorine pac container is made of HDPE plastic. Non-refillable container. Do not reuse or refill this container. Offer for recycling if available. Rinse thoroughly before recycling or discarding in trash.
Mark your calendar ahead for the approximate replacement times for the Pool FROG Bac Pac.

Operate

Winterizing

If Pool FROG Bac Pac still

Turn pump off and turn dial

contains chlorine, wrap in

to Setting 0.

plastic bag and store in shed or

cool, dry, well-ventilated location

away from children, pets, cars,

motorcycles or anything metal

that can rust, pit, etc.

If empty, rinse and recycle.

Remove cap.

WARNING
Avoid sparks, smoking, or any open flame near Pool FROG Cycler or chemicals.

Remove the Pool FROG Mineral

Reservoir and discard in trash.

You will hear spent media

inside, however, it is no longer

3. Unscrew knob from the front

effective.

of Pool FROG Cycler. Allow

all water to drain.

6. Replace the cap and knob
   loosely.

17

Troubleshooting
For more in-depth troubleshooting, go to frogproducts.com or call King Technology at 800-222-0169.

Problem

Remedy

1. What do I do if the water looks cloudy?
2. What do I do if the water turns color?
3. What do I do if algae forms in or on my pool?
4. What do I do if I am under chlorinating with the Pool FROG Bac Pac?

1. Make sure your filtration system is working properly (i.e. clean filter, skimmer and pump basket).
2. Make sure circulation time is adequate ­ increase pump

time if not.
3. Make sure the pool is properly balanced. (See page 10.)
4. Shock the water to eliminate build up of any organic matter.

5. Make sure pool has a free chlorine reading of 0.5 to 1.0 ppm.
6. Check with your dealer for more information.

1. Algae may be trying to form ­ shock the pool, increase circulation time if needed and clean the filter.

2. Metals in the fill water may have been oxidized. Have the pool tested. See pool dealer if a metal control product is required.

3. Check with your dealer for more information.

1. Use FROG BAM or an effective algaecide per the directions on the bottle and brush the sides of the pool often.
2. Clean the filter and shock the pool with chlorine daily until

water clarity returns.
3. If you are in an area of the country that struggles with algae growth, see your dealer regarding a 90-day Algae Protection Guarantee using

FROG BAM. See product hang tag for guarantee details.
4. Check with your dealer for more information.

1. If you are unable to maintain 0.5 to 1.0 ppm, first make sure there are chlorine tablets in the tower areas of the Pool FROG Bac Pac and it is installed properly. If a correction was made, test the water in 24 hours.
2. If still low, turn the dial up one setting and test the water again in 24 hours. Continue raising the setting by one increment each day until the

proper reading is achieved.
3. Shock the pool if the reading has been lower than 0.5 ppm for more than one day.
4. Make sure pump run time is at least 6 hours on high speed (40 gpm or higher) or if not, bleed the air from the back knob each time cap is open.
5. Contact your dealer to have your back pressure tested. If under 4 psi consider a smaller

eyeball fitting in the return jet.
6. Check for a suction side leak by looking for air bubbles in your pump basket or at the return jet. Contact dealer for help in correcting this situation.
7. Contact King Technology’s Customer Service Department at 800-222-0169.

5. What do I do if I am over chlorinating with the Pool FROG Bac Pac?
18

1. If the chlorine reading is over 3.0 ppm, remove the Pool FROG Bac Pac from the Pool FROG Mineral Reservoir and test the water daily until the reading is down to 1.0 ppm.
2. Reinsert the Pool FROG Bac Pac, lower the dial one setting and test the water again in 24 hours. If the reading has risen, lower the dial one setting again. Continue this process until proper reading is achieved.

3. If over-chlorinating at the lowest possible setting, consider decreasing the circulation time. Depending on your pump size, you may be circulating the water more than is necessary.
4. Contact your dealer to have your back pressure tested. If over 8 psi consider a larger eyeball fitting in the return jet.
5. Check to see if the pressure relief valve is loose or missing

and replace. See parts diagram on page 19.
6. If these steps are not successful and your Cycler is installed using the 6″ nipple, we have found changing the installation can make a difference. You will need a section of flex hose and 2 hose adapters to do this. See page 8 for directions.
7. Contact King Technology’s Customer Service Department at 800-222-0169.

Parts List Model 6100
12 13
14 15

Troubleshoot

Included with Pool FROG Cycler 6100

REF. # DESCRIPTION

QTY. INCLUDED

1 & 2 Cap w/O-Ring

1

3

Body

1

4

Pressure Relief Valve

1

5, 6, 7, 8 Control Dial with O-Rings,

Locking Pin and Number Plate 1

9 & 10 Knob with O-Ring

2

11

Mounting Base

1

12

Silicone Lubricant

1

13

Nipple Kit

1

Replacement parts for Pool FROG Cycler 6100

REF. #

PART NO.

DESCRIPTION

1 & 2 2 4 5, 6, 7, 8

01-22-1427 01-22-1922 01-22-9485 01-22-1458

6 9 & 10 11 12 13 14 15

01-22-1456 01-22-9623 01-22-1480 01-22-9972 01-22-1711 01-22-4000 01-22-1470

Cap w/O-Ring Cap O-Ring Pressure Relief Valve Control Dial with O-Rings, Locking Pin and Number Plate Control Dial O-Ring Set Knob with O-Ring Mounting Base Silicone Lubricant 3/4 oz. Nipple Kit Pressure Gauge 25k Tune-Up Kit

19

Pool FROG Cycler Maintenance
Replacing the Control Dial O-Rings

Center of locking pin

In the back of the Pool FROG Cycler, depress center of locking pin with a finger and pull pin out of dial.

Turn control dial back and forth

as you pull it out of the housing.

3. Replace both O-rings. Apply silicone lubricant that came with your Pool FROG Cycler on O-rings.
   Product # 01-22-9972

Carefully insert control dial back into housing.
Replace locking pin by pushing it through the slots on the dial until it locks into place.

20

Troubleshoot

Pool FROG Cycler Maintenance
Replacing the Cap O-Ring
1. Remove old O-ring.

2. Bottom half of groove.

Top half of groove.
Place new O-ring in bottom half of groove.

Replacing Knobs
To replace, simply unscrew old knob and replace with the new one.

1. Front of Pool FROG Cycler

3. Place your thumbs on each side of the cap over the O-ring in the groove.
2.

O-ring in top

of groove

Roll your thumbs back and forth over the O-ring while pushing upward until the O-ring falls into the top of the groove.

Back of Pool FROG Cycler

5. Product # 01-22-9972

Lubricate O-ring every couple of months with silicone lubricant that came with your Pool FROG Cycler.
DO NOT USE petroleum based lubricants.

21

For limited warranty terms and to register your product, see frogproducts.com/reg or call 1-800-222-0169. Failure to register your product does not diminish your warranty rights.
Made in U.S.A. Patents: kingtechnology.com/IP
6000 CLEARWATER DR | MINNETONKA, MINNESOTA 55343 800-222-0169 | frogproducts.com
20-48-0151 1023R12
22

References

• FROG® Pool and Hot Tub State of the Art Sanitizing Solutions with Fresh Mineral Water
• POOL FROG® 6100 Mineral Pool Sanitizer uses up to 50% less chlorine
• Register your FROG® Product | FROG® Products
• IP - King Technology

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>