VIGOR 60828HD Rear Air Springs Kit Instruction Manual

VIGOR 60828HD Rear Air Springs Kit

Product Information

Specifications:

• Compatible with: 2019-2022 Dodge Ram 1500 Pickup, 2WD & 4WD
• Installation: Air Suspension Kit
• Valve System: Single valve inflation system

Product Usage Instructions

• Introduction:
  The purpose of this publication is to assist with the installation, maintenance, and troubleshooting of the air spring kit. It is crucial to read and understand the entire installation guide before beginning any work.

Safety Precautions:
Ensure safety precautions are taken during installation to prevent any accidents or injuries. Follow all guidelines provided in the installation manual.

Installation Steps:

1. Jack up the rear of the vehicle or raise it on a hoist, supporting the frame with safety stands.
2. Remove any rubber isolator present at the top of the passenger’s side coil spring.
3. Exhaust air from the air spring and fold it into a hot dog bun shape.
4. Insert the flattened air spring into the coil spring through the lowest opening with the stem at the top.
5. Allow the air spring to assume its molded shape and position the cylinder at the bottom of the coil spring for hose attachment.

FAQ

Notation Explanation:

• DANGER: Indicates immediate hazards that can result in severe personal injury or death.
• WARNING: Indicates hazards or unsafe practices that could lead to severe personal injury or death.
• CAUTION: Indicates hazards or unsafe practices that could result in damage to the machine or minor personal injury.

Hardware List:
A B C D E F G H I J K L M

Tools List:
List of tools required for installation not provided in this text excerpt. Refer to the complete installation manual for details.

Air Suspension Kit for

• 2019-2022 Dodge Ram 1500 Pickup, 2WD & 4WD 2019-2022
• Ram 1500 Pickup, 2WD & 4WD

Installation Manual

• Thank you for purchasing the 7X 60828HD Kit! Please kindly be advised to read the  instructions carefully before installing the air suspension kit.
• Please take safety precautions accordingly during installation.
• The installation instructions are based on the left side or based on the driver’s side of the vehicle, and the structure on the right side can refer to the same method on the left side.
• The retrofit kit you purchased is a single valve inflation system.
• Please note that the air spring will bend and expand under working conditions. Ensure there is enough space for it to work properly and avoid friction between the air spring and other chassis parts.

Introduction

• The purpose of this publication is to assist with the installation, maintenance and troubleshooting of the air spring kit.

• It is important to read and understand the entire installation guide before beginning installation or performing any maintenance, service or repair. The information here includes a hardware list, tools list, step-by-step installation information, maintenance guidelines and a checklist for after completing the installation.

• Our Company reserves the right to make changes and improvements to its products  and publications at any time. . .

NOTATION EXPLANATION

• Hazard notations appear in various locations in this publication. Information which is highlighted by one of these notations must be observed to help minimize risk of personal injury or possible improper installation which may render the vehicle unsafe. The following definitions explain the use of these notations as they appear throughout this guide.
• DANGER
  • INDICATES IMMEDIATE HAZARDS  WHICH WILL RESULT IN SEVERE PERSONAL INJURY OR DEATH.
• WARNING
  • INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN SEVERE PERSONAL INJURY OR DEATH.
• CAUTION
  • INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN DAMAGE TO THE MACHINE OR MINOR PERSONAL INJURY.

Installing the Air Spring Kit

GETTING STARTED

1. Jack up the rear of the vehicle or raise on a hoist. Support the frame with safety stands (Fig. 1). Lower the axle or raise the body of the vehicle until the springs are completely extended.

2. Some models may have a rubber isolator at the top of the passenger’s side coil spring. This isolator needs to be removed and can be discarded (Fig. 2).

3. Remove the plastic cap from the barbed stem on the end of the air spring (A). Exhaust the air from the air spring by rolling it up toward the stem. Replace the cap on the stem to hold the flat shape (Fig. 3). Fold air spring into a “hot dog bun” shape.

4. Insert the flattened air spring into the coil spring through the lowest opening with the stem at the top (Fig. 4). Push the air spring up within the coil by hand or with a blunt instrument such as a spoon-type tire iron.
   CAUTION
   DO NOT USE A SHARP OBJECT TO PUSH THE AIR SPRING INTO PLACE.

5. When the air spring is completely within the coil, remove the cap and allow the air spring to assume its “as-molded shape.” Push the cylinder down to the bottom of the coil spring so that the stem at the top can be accessed for attaching the hose.

Installing the Air Line

• A single-path air line installation is recommended for vehicles that typically have even weight distribution (Fig. 5). If weight in the vehicle varies from side to side and unequal pressures are needed to level the load, use a dual-path installation. For dual-path air line installations, eliminate the tee fitting (J) and route separate air lines for both air springs (Fig. 6).

CAUTION

TO PREVENT THE AIR LINE FROM MELTING, MAINTAIN AT LEAST 6” (152MM) FROM THE EXHAUST SYSTEM TO THE AIR LINE.

1. If installing a single-path air line, choose a location for the tee fitting (J) on the frame rail or crossmember. Determine and cut adequate length of air line (C) to reach from tee to the left and right side air springs.
   CAUTION
   LEAVE SUFFICIENT AIR LINE SLACK TO PREVENT ANY STRAIN ON THE FITTING DURING AXLE MOTIONS.

2. Use this procedure (Fig. 7) for all air line connections:

   • Slide the air line clamp (L) onto the air line.
   • Push the air line and air line clamp over the barbed stem so that the air line covers all the barbs.
   • Compress the ears on the air line clamp with pliers and slide it forward to fully cover the barbs.

3. Select a location for the Schrader valve (K), ensuring that the valve will be protected and accessible with an air hose (Fig. 8). Determine and cut adequate length of air line (C) to reach from the tee to the Schrader valve or from the air springs to the valve if using a dual-path installation.

4. Drill a 5/16” (8mm) hole for the Schrader valve (K) and mount as shown (Fig. 9). Install the air line on the Schrader valve first. The rubber washer (G) serves as an outside weather seal.

5. From the tee, route the air line along the top of the frame on both sides to, and down through the top spring seats, through an air spring protector (B) to the air springs (Fig. 10). Leave sufficient slack to prevent any strain on the fitting during axle motions. Cut the air line to length using a sharp knife.

6. Attach the straight pump connector (M) to the air line (Fig. 10). Attach the straight pump connector to the air spring fitting. Do not use any tools to tighten the fitting.
   CAUTION
   DO NOT INFLATE THE AIR SPRINGS BEFORE READING THE MAINTENANCE AND USE GUIDELINES IN THIS INSTALLATION GUIDE AS WELL AS THE USER GUIDE INCLUDED WITH THIS KIT.

COMPLETE THE INSTALLATION

1. Once the air lines have been installed, raise the suspension or lower the body so that the air spring just touches the top and the bottom of the upper and lower spring mounts. Inflate the air springs to 5 PSI (.34BAR).
2. Remove the safety stands and lower the vehicle.

Before Operating

Consult the included User Guide for information about fixing air leaks along with more tips for maintenance and use before using the product.

INSTALLATION CHECKLIST

• Clearance test — Inflate the air springs to 25-35 PSI (1.7-2.4BAR) and make sure there is at least 1/2” (13mm) clearance from anything that might rub against each air spring.
• Leak test before road test — Inflate the air springs to 25-35 PSI (1.7-2.4BAR) and use a soapy water solution to check all connections for leaks. All leaks must be eliminated before the vehicle is road tested.
• Heat test — Be sure there is sufficient clearance from heat sources, at least 6” (152mm) for air springs and air lines. If a heat shield was included in the kit, install it. If there is no heat shield, but one is required, call customer service at + 1-604-636-8654.
• Road test — The vehicle should be road tested after the preceding tests. Inflate the air springs so that the vehicle is level. Drive the vehicle 10 miles (16km) and recheck for clearance, loose fasteners and air leaks.
• Operating instructions — If professionally installed, the installer should review the User Guide with the owner. Be sure to provide the owner with all of the paperwork that came with the kit.

MAINTENANCE AND USE GUIDELINES

1. Check air pressure weekly.
2. Always maintain normal ride height. Never inflate beyond 50 PSI (3.5BAR).
3. If the system develops an air leak, use a soapy water solution to check all air line connections and the inflation valve core before deflating and removing the air spring.

• CAUTION

  • FOR SAFETY AND TO PREVENT POSSIBLE DAMAGE TO THE VEHICLE, DO NOT EXCEED MAXIMUM GROSS VEHICLE WEIGHT RATING (GVWR) OR PAYLOAD RATING, AS INDICATED BY THE VEHICLE MANUFACTURER.

• CAUTION

  • ALTHOUGH THE AIR SPRINGS ARE RATED AT A MAXIMUM INFLATION PRESSURE OF 50 PSI (3.5BAR), THE AIR PRESSURE ACTUALLY NEEDED IS DEPENDENT ON LOAD AND GROSS VEHICLE WEIGHT RATING.
    CUSTOMER SERVICE:

  • If you have any questions about this product, please contact us below:

  • Email： support@vigorair.ride.com .
    Thank you very much!

References

• Website Under Construction
• SOM - State of Michigan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>