DINDON B0BS1794NS Pull Out Spice Rack Cabinet Organizer Instruction Manual

Pull Out Spice Cabinet Organizer
Installation Manual

B0BS1794NS Pull Out Spice Rack Cabinet Organizer

Note! Inspect all parts and read all instructions prior to beginning assembly and installation

Tools Required

• A Power Screwdriver or A Philips Head Screwdriver

PART LIST

Part
Code| Name| Simplfied Diagram| Quantity| | Part
Code| Name| Simplfied Diagram| Quantity
---|---|---|---|---|---|---|---|---
A| Front
Panel| | 1 PCS| | K| M420 Screws| | 14 PCS
B| Rear Board| | 1 PCS| | L| ST416 Screws| | 8 PCS
C| Bottom
Board| | 1 PCS| | M| ST425 Screws| | 8 PCS
D| Connect
Panel| | 2 PCS| | N| M518 Screws| | 8 PCS
E| R ow
Divider| | 3 PCS| | 0| M56 Screws| | 4 PCS
F| Slides
Backing
Plate| | 1 PCS| | P| ST414 Screws| | 12 PCS
G| Adjusting
Clips| | 1 Pair| | Q| Row Divider
Plastic Buckle| | 12 PCS
H| Drawer
Slide| | 1 Pair| | R| Row Divider
Fixing Screws| | 12 PCS
I| Anti-Sway
Wheel| | 2 PCS| | S| Door Panel
Connector| | 4 PCS
J| Anti-Sway
Wheel
Mount| | 2 PCS| | T| Block Pole| | 6 PCS

1. Install 12 pcs row divider fixing screws(R) to parts (A) and (B)
   

2. Assemble the parts(A),(B),(C), (D), fix them with 14 pcs m4*20 screws(K)
   

3. Install the adjusting clips(G) to the front bottom of the organizer with 8 pcs ST4*14 screws(P)
   

4. Assemble row divider plastic buckle(Q) and block pole (T) to row divider (E)
   

5. Clamp the 3pcs assembled (E) into the row divider fixing screws(R) on (A)(B) board’s
   

6. Mount door panel connector(S) to front panel (A) with 8pcs M5*18 screws (N)
   

7. As shown below, place the slides backing plate(F) on the bottom of the cabinet, and then pre-drill 8*2.5mm holes according to the 8 holes on the board
   

8. As shown below, respectively pre-drill 2 2.5mm holes on the cabinet left and right

9. Fix the drawer slides(H) on the backing plate(F) with 8 pcs ST4*25 screws(M)

10. Install anti-sway wheel
    a: Install anti-sway wheel mount base(J) with 4pcs ST416 screws(L).
    b: Install anti-sway wheel(I) on the anti-sway wheel mount base(J), adjust to the highest position, then fix with M56 screws (O)
    

11. Install the organizer onto the slide rail
    Fully extend the drawer slides, put the organizer on the drawer slides and align notches on the rear board with the slides, and then push the organizer into the cabinet
    

12. Adjust the anti-sway wheel(I), after make sure part (I) tightly attached to connect panel(D), tighten the screws on the wheel
    

13. As below shown, pre-drill 4 2.5mm holes on the cabinet door
    

14. Install the cabinet door and fixed with 4pcs ST4*16 screws(L)
    

Customer Service: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>