MEJE MZE014P Wisdom Knows Better Automatic Intelligent Toilet Instruction Manual

MEJE MZE014P Wisdom Knows Better Automatic Intelligent Toilet

Safety directory

Please cautiously read before installing and using.

Warning- To avoid electric shock

1. Do not place the product where it may get wet.
2. Do not drop the remote control into the water.
3. Do not spray water into the product or plug.

Warning: To prevent the possibility of burns, electric shocks,fires and injuries.

1. Young children, temperature insensitive users, when using this product, should be accompanied by others. And turn off or lower the seat temperature.
2. The product is limited to the function on the manual, do not use other equipments.
3. Do not continue to use when the product is out of order, damaged or flooded. Please send the product to the designated repair center for repair.
4. Please make sure that the wires are not damaged by burning.
5. Do not use this product when you are out of your mind.
6. Do not plug the product or pipe.
7. Do not used outdoors.

Please be sure to observe the following

Please don’t sprinkle urine at the essence and spray. Pull out the plug when it thunders.

Strictly forbid to directly flush with water.

Please do not wipe seat and cover with dry cloth or toilet paper.

Please do not open the seat ring or cover violently.

• May cause cracking or malfunction.

Please take antifreeze measures to prevent damage caused by freezing.

Please do not put heaters near this product.

• Discoloration or malfunction will occur

Safety Caution

Note: please cautiously read before using

Please read carefully before using. The cautions listed here are related to safety and please follow.

This product is an electrical product. Please do not install it in a place where it is easy to be splashed by water or high humidity. When using in the bathroom, please install a vent to keep good air flow in the bathroom.

The socket for power distribution should be set as follows

• The gearing position of electric outlet pleases to give examples 0.3 min the ground above, and leave bathtub as far as possible a little bit farer.
• The back track of electric outlet pleases use a high feeling and rapid type electric leakage switch(the sum certainly responds the electric current 15 mA following) or use to insulate the transformer 1.5 KVA above, the 3 KVA is following)carry on a protection .

The product connects a ground of line to carry on to connect a ground of processing, if has never carried on to connect a ground of processing, may arouses to get an electric shock.

Note: the grounding treatment mentioned here means that the grounding resistance is below 1000, and the grounding wires of the switchboard shall be copper wires with a diameter of more than 1.6mm.

While using in the bathroom please confirm the power plug have already used silica gel to carry on a waterproof processing.

Examples and illustrations of ICONS

| It is not feasible (prohibited). The image on the left shows (disassembly is prohibited).
---|---

| Represents something that must be (enforced). The left-hand diagram shows (must comply).

Must obey

Notice heat burn

• Please turn the seat temperature down or off when sitting on the toilet for a long time.
• Please set the temperature to room temperature when the following persons use the seat to dry gently.
  • Children, the elderly, the sick, the disabled, etc .
  • People who take sleeping pills, get drunk and get overtired .

Do not use any power source other than AC 220V/110V

• It may start a fire
  

Keep cigarettes and other fire kindling away from the product.

• It may start a fire

Do not use loose and unstable power sockets.

• It may cause fire or electric shock

Please don’t sprinkle water or rinse on product essence or the power plug.

• May arouse a fire or get an electric shock
• May cause toilet break , damage or indoor seepage.

When long lime didn’t use, please pull out the power plug.

• For safety, please pull out the power plug
• For reuse, please drain water for one minute before use.

Please do not flush other items except for urine and feces

• May cause then block, sewage outside overflows

Do not unplug the power plug with wet hands

• It may cause electric shock

Do not distort or damage the water inlet

• It may cause a leak

Prohibit

Do not continue to use the product when it breaks down

When the following occurs, please unplug the power plug, close the inlet Angle valve, stop the inlet.

• Ceramic WC is leaking
• Abnormal sound and smell
• Fume-off
• Abnormal heating
• The toilet is clogged
• If continued under the condition of failure, it may cause fire, electric shock or indoor seepage problems

Do not disassemble, repair or transform the product without permission

• It may cause a fire or electric shock

Do not install this product in damp places such as bathrooms

• It may cause a fire or electric shock

Do not damage the power cord or toilet seat cable

• Don’t pull
• Don’t process
• Don’t heat
• Don’t forcibly bent
• Do not place heavy objects on the power cord and toilet seat connection line.
• May cause fire, electric shock or short circuit. If the power supply is damaged, please contact a professional for repair.

Do not use extension wires. otherwise, it may cause a fire or electric shock

• Do not connect wires or use extension cords, which may cause fire and electric shock.

Do not use unhealthy water

• May cause skin irritation and other problems

The first use of Intelligent toilet

Note: To ensure the normal use of the product, please follow the instructions to text.

1. Insert the power plug into the AC (AC) 220/110V socket
2. Please confirm whether the indicator of the digital display panel is lit
3. Confirm whether the inlet valve is take on
4. Whether the hose between the wall Angle valve and the toilet inlet valve is installed in place.

1. Unscrew the screws , then remove the cover
2. Connect the air pipe and the water pipe of the water tank with the pipe of the ceramic toilet.
   

Caution-Confirmed matters before using

1. Check whether the sprinkler head and water pipe leak, dry all parts of the water pipe and check with blotting paper.
2. Press the seat around the seat sensor, whether there is a sound.
3. Check whether the cleaning, drying, automatic deodorization and automatic flushing are normal
4. Whether the Damped structure is normal.
   

Check the functions of cleaning, drying and automatic deodorization, make sure the sensor is on.When cleaning, cover and block the spray nozzle, so as not to splash.

Warning – Be sure to firmly connect ground wires

The power plug of this product is a three-phase plug (with ground wire).

There is a danger of electric shock when there is a fault or leakage of electricity.

If there is no ground plug in the socket, consult with the electrical installation company.

Do not use power supply other than AC 220V/11 0V, please wiring according to relevant regulations.

Using the wrong power supply can easily cause fire

1. Radar switches to foot cover: press the cover button on the remote control for 5 seconds,
2. Turn off / turn on disseat water flushing: press the automatic water flushing button on the remote control for 5 seconds
3. Turn off / turn on the function of flushing upon cover falling: press the cover and flushing buttons on the remote control at the same time

Instructions for remote control

Note: Please read the following carefully before use

HIP/ MOBILE

Press this button when you are seated, the Hip wash cleaning nozzle will spray at the fixed position for 2 minutes and then stop spraying automatically.

FEMALE/ MOBILE

Press this button when you are seated, the female cleaning nozzle will spray at the fixed position for 2 minutes and then stop spraying automatically.

MASSAGE

Press this button to hip cleaning and message. The massage is generated through regular changes in the water pressure to promote blood circulation

FLUSH

Press this button and will start flushing.

DRYING

Press this button to start drying when you are seated. Warm air drying wi!I stop automatically after 3 minutes.

POWER

Press this key to open or shut off the power

Water Temperature

4 degrees can adjust the water temperature the temperature can be set as , one degree : the environment temperature,second degree :34°C,
Third degree :37°C,
Fourth degree : about 40 °C

Seat Temperature

4 degrees can adjust the seat temperature the temperature can be set as,one degree : the environment temperature,second degree :34″c,
Third degree :37″c,
Fourth degree : about 40 °C.

Wind Temperature

4 degrees can adjust the wind temperature the temperature can be set as , one degree: the environment temperature, second degree:about 35°C,
Third degree :about 45°C,
Fourth degree : about 55 °C.

CLEANING HEIGHTEN

It can increase or decrease the force of cleaning water pressure. It can be set to weak, medium, strong, or strongest.

FORWARD

Press this button during the “hip” or “female” cleaning and adJust the nozzle position without the use of the removable cleaning function.

STOP

You can stop the “Hip cleaning”, “Female cleaning”, “Drying” and other functions in operation.

NIGHT LIGHT

The night light can be turned on or off in me power-on state.

NOZZLE CLEANING

Nozzle extended and water out for nozzle washing

ENERGY SAVING

The monitor or indicator light of the toilet goes off, and the toilet enters the state of intelligent power-saving standby.

This key is only applicable to the type of sensor flip-over

COVER

Press this button, the seat cover will open automatically, and then press it again, the seat cover will close automatically.

SEAT

Press this button, the seat opens automatically, and press again to close the seat automatically.

CODE FOR REMOTE CONTROL

Rotate the knob until the buttocks are clean and hold for about 3 seconds. After a sound, press any button of the remote control to complete the code.

Note: If the remote control has no response in the first time, it should be code.

Side Knob Instructions

• Power on/off : long press the knob for more than 3 seconds
• Hip cleaning: Turn the knob to the left
• Female cleaning : Turn the knob to the right
• Stop : Press the knob once
• Toilet flushing : Press the knob once before seating
• Warm air drying : Press the knob once when seating

Description Of Other Functions

(Flushing by foot sensor ) Close to the foot sensor, turn on the scour function (manual clamshell)
( Open cover and seat by foot sensor ) Close to the foot sensor, automatically open/close cover and seat (automatic flip cover)
( Radar automatic clamshell function ) Close to the toilet, automatically open the cover, automatically close the cover after leaving and flush automatically (automatic flip cover)

Daily Cleaning And Maintenance

Note: During cleaning and maintenance, please be sure to unplug the power switch and power off

Smart toilet cleaning and maintenance methods

Please wipe it with a soft cloth dampened with water

• If the dirt is not removed in time, it will become difficult to clean,  please wipe with water sometimes.
• Static electricity will absorb dust, resulting in the product black, dirty, water wipe can prevent the generation of static electricity.
• The ceramic body can be removed from the toilet seat to facilitate cleaning between the toilet seat and the ceramic body.
  Unplug the power supply before maintenance

Cleaning and maintenance of spray head

If there is dirt in the nozzle. Please clean it with a small brush such as a toothbrush.

• Do not stretch and bend the spray head.

Clean the dust on the power plug regularly

When cleaning, remove the power plug and wipe with a dry cleaning cloth.

Must obey – Poor insulation may cause a fire.

Common Fault Diagnosis

Note : If similar fault is found, please read the following solution or contact after sales

the circuit
Weather there is leakage (the display light of leakage protection plug is not on)| Remove the power plug from the socket and replug it later press the reset switch off the leakage protection plug. If the the elbow still cannot be operated please unplugged the power plug and intrust the repair.
No water with spray| Check if water is cut off| Pending resumption of water supply
Check that the Angle valve is closed| Open the Angle valve
Check if the inlet filter is blocked| Clean or replace the filter
Check the inlet pipe for bends| Exclude the intake bend
Cleaning insufficient rigidity| Check whether the cleaning pressure is at the lowest level| Refer to the instruction manual for regulating the water pressure
Check if the inlet filter is blocked| Clean or replace the filter
Spray water disorderly| Abnormal operation| Unplug the plug for one minute and then switch it back on
Water temperature is not enough| Check that the water temperature is set low| Adjust the water temperature according to the instructions
Whether the hot and cold massage function is on.| Turn off the hot and cold massage function according to the instructions
The washer often drips water| Solenoid valve failure| Please get professional maintenance technicians
Misoperation of remote control| Check the battery level of the remote control is it too low| Please replace the battery
Drying/seat temperature too low/no heating| Check whether the temperature is set at low or normal temperature| Adjust the temperature according to the instruction
Whether to turn on the power saving function| Refer to the manual to choose to turn off the power saving function
Seat/ cover falling too fast| Failure of damping drop function| Please get professional maintenance technicians
The cleaning function cannot be used normally| Is there any other hard material holding it under the seat| Remove the hard objects
Whether the body’s sensing area is covered| Adjust the body sensing area of the seat cover
Whether the power supply is restored during the power failure| Unplug the plug for one minute and then switch it back on
The skin completely cover the human body induction area of the seat| Sensor failure, please get professional maintenance technicians
Seat/cover cannot be opened or closed

• Only for automatic flip machine

| Failure of automatic damping function|

1. Disconnect the plug for one minute and switch it back on
2. The above treatment is invalid, please ask professional personnel for maintenance

Low water pressure does not flush clean| Filter mist blocking| Clean the filter according to the instruction
Pipe bending| Observe whether the connection line bends and keep the water supply line smooth
No siphon flushing is not clean when water pressure is normal| Air escapes from the sewage outlet| Please get professional maintenance technicians
The S-bend is blocked| Please buy water pipe dredger in the market for dredging
Flush is not clean when water pressure normal| Flush valve failure| Ask professionals for maintenance

Product Standard

40°C Water discharge: 750ml/min        Power: 1350W
Cleaning| Water outlet| Hip cleaning| About 700 ml/min
Female cleaning| About 700 ml/min
Outlet water temperature| Normal temperature, and 34°C/37°C/40°C(4 grades)
Water heating| Instant water heater
Heater power| Water inlet temperature: 15°C , Outlet water temperature: 40°C Water discharge: 750ml/min         Power: 1350W
Seat heating| Seat temperature| Normal temperature, and 34°C/37°C/40°C(4 grades)
Heater power| 40W
Warm drying| Wind temperature| Normal temperature, and 35°C/45°C/55°C(4 grades)
Spray position| Adjustable Fore and Aft
Water temperature| 5~40°
Water Pressure ( With Water Tank )| The lowest pressure : 0.06 Mpa the highest pressure: 0.75 Mpa ( static)
Water Pressure ( Without Water Tank )| 0.15-0.75 Mpa (static) is about 5L of water in 15 seconds

Due to the different printing time of the material, the product specification may be slightly changed please refer to the material object.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>