Torchbeam H11 LED 6000K Cool White Plug and Play LED Bulbs Instruction Manual

: June 1, 2024
: Torchbeam

Table of Contents

PRODUCT INTRODUCTION
INSTALLATION INSTRUCTIONS
FAQ
WARRANTY DESCRIPTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Torch beam H11 LED 6000K Cool White Plug and Play LED Bulbs

Torch beam H11 LED 6000K Cool White Plug and Play LED Bulbs

PRODUCT INTRODUCTION

Accessories list:
- LED Bulb x2
- Note Card xl
- User Manual xl
- Glovesx2
Features:
Perfect beam pattern. fully illuminating the road during driving.
High compatibility with Can BUS system, fit most vehicle’s systems without error.
Simple installation. plug and play. long life.
Product specifications
** Operating voltage| DC (9 -16V)
---|---
IP rating| IP67
Color temperature| 6000-6500K
Operating temperature| -40°C-8S°C
LED chips| High-brightness LED chips
Heat sink| ADC12**
Warranty| 2 years
User instructions
- Please purchase the product through official channels, otherwise we won’t provide after-sales service.
- As the product has small & sharp parts. please keep it away from children.
- After receiving the product, please carefully check whether it is damaged or any part is missing. If there is any problem. please contact Customer Service .
- This product is only fit for vehicles which use 12V batteries. High voltage may cause damage.

INSTALLATION INSTRUCTIONS

Matters needing attention:
Please light-up the bulb before installation.
The OE halogen bulb would be extremely hot for a quite long time after shutting down the engine. To avoid burns, please wait at least 2 hours before replacing the lamps.
Wear gloves while replacing the lamps, and do not touch the LED chips.
If the lamps do not light-up , please unplug the power line, connect it reversely and try again.
Models: 9005/9006/Hl 1/9012

Fig. 1: Remove the dust cover and the OE halogen bulb.

Fig. 2: Line-up the retainer holder with the slot of the assembly.

Fig. 3: Insert the lamps. turn them clockwise, then clamp tightly.

Fig. 4: Connect the power line.
Model: Hl/1-13/1-14/1-17

Fig. 1: Remove the dust cover and the OE Halogen bulb. Hold the base of the lamps and tum counter-clockwise until it is unlocked, and then remove the OE Halogen bulb.

Fig. 2: Insert the LED bulb into the assembly and align the tabs of the ring with the slot of the assembly.

Fig. 3: Fix it in place with a spring clip.

Fig. 4: Connect the power line.
Model: 9004/9007

Fig. 1: Remove the bulb retainer and OE halogen bulb from the vehicle.

Fig. 2: Assemble the LED lamps with the bulb retainer together.

Fig. 3: Then insert them into the assembly.

Fig. 4: Connect the power line.
Models: Hl 3

Fig. 1: Remove the dust cover and the OE halogen bulb.

Fig. 2: Line-up the retainer holder with the slot of the assembly.

Fig. 3: Insert the lamps. turn them clockwise, then clamp tightly.

Fig. 4: Connect the power line.
Suggestions
According to most vehicles’ configurations , were com md keeping the LED chips facing the 3 o clock and 9o’clock positions to ensure the best beam pattern and visual effect . However, it is impossible to adjust to this position for some vehicles . There is no need to worry about the position of the LED chips as long as the beam pattern is acceptable Picture 😀 chips facing 3 o’clock and 9 o’clock positions.

If you are not satisfied with the light pattern and visual effect after installation. please operate and adjust according to the figure
Adjust the buckle

If you are not satisfied with the beam pattern. then please try to adjust the beam pattern as photo shows.
( only for 9005&9006)

FAQ

Q: The model of lamps I purchased is different from my OE halogen lamps.
Can I get an exchange for the correct model?
A: The main reasons:
J Amazon Confirmed Fit system is not 100% accurate.
Your headlight assembly is not an OE part. Please double check the model of your OE halogen bulb. And contact our Customer Service.
Q: The size of the lamps is not correct. they’re either too long or too wide. and LED lamps can’t be installed into the headlight assembly. How can I get proper size lamps for my car?
A: Some LED lamps are not in a 1:1 ratio with the OE halogen bulbs. The large base is for better heat dissipation and prolonging the life of the lamps. If the lamps are not suitable for installation. please contact the Customer Service.
Q: Do you meet the five phenomenon’s below?
Errors on instrument panel;
The Lamp keeps flashing;
Can’t switch between high and low beams;
High and low beam reversed;
The Lamp does not turn on or off.
A: The above phenomenon’s are decoding problems. which are mainly caused by the automotive computer failing to detect the correct signal. You can contact Customer Service to obtain the decoder and solve the decoding problem.
(decoder installation drawing or video)
Q: How to adjust the lamps to 3-9 o’clock? I’ve read all the instructions but still can’t find the method
A: We recommend keeping the LED chips facing the 3 o’clock and 9 o’clock positions to ensure the best beam pattern and visual effect. However, it is impossible to adjust to this position for some vehicles. There is no need to worry about the position of the LED chips as long as the beam pattern is acceptable.
Q: The Daytime Running Lamps work incorrectly. it keeps flashing.
How can I solve the issue?
A: If your Daytime Running Lamp and High beam is the same bulb. the case would be complicated to solve. Please contact Customer Service.
Q: After installing the LED lamps. I found my High beam and Low Beam reversed. Is there any way to solve this problem?
A: It is recommended to remove the lamp. rotate by 180° and install it again. If the problem still exists, please contact Customer Service.

WARRANTY DESCRIPTION

Thank you for purchasing our products. All of our products are manufactured with best quality control To protect your rights. you can extend the warranty period for 2 years.