FLASHFORGE Adventurer 5M Pro Desktop 3D Printer User Guide

FLASHFORGE Adventurer 5M Pro Desktop 3D Printer

WARNING

1. Please refer to this Guide for initial printer setup.
2. Hot! Avoid touching the heating nozzle in operation.
3. Moving parts in the printer may cause injuries.
4. Do not wear gloves or other sources of entanglement in operation.

Safety Notice

• Do not power on the printer until installation is completed.

Unboxing Instructions

1. Open the box.
2. Remove the upper foam packaging, Quick Start Guide and After-sales Service Card.
3. Take out the machine, place it on a level workspace and remove the packaging bags and tapes.
4. Open the top cover and remove the upper protective foam.
5. Remove the filament, power cable, USB flash drive, and 0.6mm nozzle from the chamber protective foam.
6. Remove the inner protective foam from the extruder. Open the front door and remove the front protective foam and accessory box.
7. Move the chamber foam according to the arrow direction.
8. Remove the foam.

Packing List

Printer Components

1. Top Cover
2. Extruder
3. Switch Button
4. Touch Screen
5. Front Door
6. Auxiliary Cooling Fan
7. Build Plate
8. USB Port
9. Air Filter
10. Screw Holes for Spool Holder
11. Ethernet Input
12. Power Switch
13. Power Socket

Install the Spool Holder

1. Take out the two screws and spool holder from the accessory box.
2. Install the spool holder at the position shown in the figure with the two screws.
3. Please tighten them using a 2.0mm Allen wrench.

Unlock the Build Plate
Please ensure the platform has been cleared up. Please use a 2.0mm Allen wrench to remove four screws that lock the build plate (as indicated by the arrow).

First Print
The interface layout may change whenever there is an upgrade of firmware.

1. Connect the power, turn on the power switch, and press the switch button to turn on the screen.

2. Following the guide on the screen, select the language. First Print Switch button

3. Turn on the Wi-Fi switch and connect to the network following the instructions.

4. A successful connection notification will pop up once connected.

5. Bind the printer following the instructions.
   (Note: If skipped, binding can still be done later on, the printer, see User Guide for details.)

   • After clicking [OK], the QR code page will appear.

6. Click [Next] and the machine will perform the first calibration. Vibrations and noise during calibration are normal.
   (Note: Please keep the machine on a stable surface and do not move it during calibration.)

   • Download Flash Maker by scanning the QR code (see right) or from the app store, register your Flashforge account, and log in. Use Flash Maker to scan the QR code on the printer screen to bind the printer to your account.
     (Note: Default printer name and location are set upon leaving the factory; after completing the startup, you can customize the printer name and location in the settings.)

7. Load filament following the on-screen startup boot: Cut off the bent part of the filament end. Hang the filament on the spool holder. Pass it through the filament sensor until it’s seen from the other end of the filament guide tube. Push it forward to the feed roller, until it can not go further. (Please use PLA filament for the first print on initial setup)

8. Click [Load] and select [PLA] for the first print.

9. Wait for the extruder to heat up.C3. Feeding will begin after heating. Successful filament extrusion from the nozzle indicates successful loading.

10. Lastly, confirm the filament guide tube is properly inserted. If no filament is extruded, manually insert the filament into the inlet and click [Back] to retry. Feel for filament movement until it is extruded.

11. Please clear the filament residues on the nozzle and platform.

12. Users must apply glue to the platform to improve adhesion for the first print.

13. Click [Print] and the machine starts printing the built-in file (configured for PLA material).

For more information, you can visit the Flashforge official website. www.flashforge.com – [Support]

Parameters

Address：3rd Floor, Building 2, No. 8 South Daxing Street, Tangxia Town, Dongguan City, Guangdong Province

References

• 浙江闪铸集团有限公司 - 工业3d打印品牌-闪铸3d打印厂家【官网】

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>