SmartBidet SB-1000 Electronic Bidet User Manual
- June 1, 2024
- SmartBidet
Table of Contents
SmartBidet SB-1000 Electronic Bidet User Manual
MPORTANT SAFEGUARDS
SB-1000.indd 4 2019-02-15 오후 2:04:50
This product has to be grounded. In the event of an electrical short
circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current. This product is equipped
with a cord having a grounding wire with
a grounding plug. The plug must be plugged into an outlet that is properly
installed and grounded. Danger – Improper
use of the grounding plug can result in a risk of electric shock.If repair or
replacement of the cord or plug is necessary,
do not connect the grounding wire to either flat blade terminal. Consult with
a licensed electrician if you have concerns
about whether the product is properly grounded.
This product is for use on a normal 120 V circuit, and has a grounding plug
illustrated in sketch A in Figure 1. A
temporary adapter, which looks like the adapter illustrated in sketches B and
C, may be used to connect this plug to a
2-pole receptacle as shown in sketch B if a properly grounded outlet is not
available. The temporary adapter
should be plugged into a properly grounded outlet (sketch A) and should be
installed by a licensed electrician.
The green colored rigid ear, lug, and the like extending from the adapter must
be connected to a permanent ground
such as a properly grounded outlet box cover. Whenever the adapter is used, it
must be held in place by the screw.
GROUND INSTRUCTIONS This appliance has to be grounded.
GROUNDING PIN
ADAPTER ADAPTER
METAL SCREW
TAB for
Grounding Screw
GROUNDED
OUTLET
– Figure 1-
The use of an extension cord is not recommended or advised. If it is necessary
to use an extension cord, use only
a three-prong extension cord (one to one), and a three slot built-in GFCI
receptacle that will accept the plug on this product. The marked rating
of the extension cord should be equal to or greater than the electrical rating
of the unit (10 amp.) Consult a licensed electrician if you are not sure
whether the unit is properly grounded.
GROUNDED
OUTLET BOX
5
E
N
G
L
I
S
H
IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK.
Electric wiring has to be done in accordance with all local codes,
or in the absence of local codes, with National Electrical Codes.
Preferred Connection Temporary Connection
This Product must be on a separat circuit. No other appliance should share the
circuit with this product.
Sharing a circuit could cause the branch circuit fuse to blow
or the circuit breaker to trip. Continuous usage under these conditions may
result in fire or property damage.
WARNING
DANGER
SB-1000.indd 5 2019-02-15 오후 2:04:50
6
3 General Caution
Do not separate, disassemble, repair or remodel the unit,
or allow foreign substances inside the unit.
ᆞThis can cause a fire or electric shock.
ᆞOnly qualified service personnel should repair this product. Disassembling,
remodeling prohibited
Do not splash water on the main unit or power cord, and do not utilize it in
areas of high levels of humidity.
ᆞThis can cause a fire or electric shock.
Do not spray water
This product must be grounded before usage and
plugged into an AC 120V/60Hz power outlet.
ᆞIf grounding is not done, it can cause fire or electric shock .
Grounding
Do not touch the power cord with wet hands.
ᆞDo not plug or unplug the power cord with wet hands as it can
cause electric shock or bodily injury. Wet hands prohibited
Do not supply electrical power to the product until it is installed on the
toilet
and the water supply hose is properly connected.
ᆞThis can cause a fire or damage the product.
Prohibited
Do not connect several power cords into one outlet.
ᆞThis unit uses 120V power outlet.
ᆞCan cause overheating or fire hazards.
ᆞPlug in the power cord properly into the power outlet. Prohibited
Use public water supply.
Do not connect the unit to industrial water or greywater.
ᆞThis can cause skin infections or urinary tract infections and also damage
the unit.
Observe at all times
Keep the cord away from cigarettes or flammable substances.
ᆞThis can cause electric shock or bodily injury.
Use of fire prohibited
Warning
SB-1000.indd 6 2019-02-15 오후 2:04:51
7
Cautions
For safety purposes, unplug the power cord when cleaning
the product or detaching the unit from the toilet bowl.
ᆞFailure to do so can cause an electric shock.
Unplugging the
power cord
Do not use a damaged power cord or a loosely fitted electric outlet.
ᆞThis can cause an electric shock.
Observe at all times
ᆞChildren, elderly, patients and those who are physically limited should use
the low temperature setting for
the seat, heater, water and dryer.
ᆞAfter using the seat warm at high temperatures, the temperature should be
readjusted to ‘low’ for the
elderly, children and for those with sensitive skin.
ᆞThose who cannot adjust the temperature or those who have sensitive skin
should take
specialprecautions. Prohibited
When cleaning, do not use cleaning detergents (oxidized products, sink
products,
toilet cleaning products, and any types of stain removers) on the external
surface of the electronic
toilet seat, and also do not spray air fresheners or aromatic products onto
seat in attempts
to eliminate odors.
ᆞUsing cleaning detergents or air fresheners can change the color of the
external surface and
can also cause problems with the seats functioning
Prohibited
Do not stand on top of the
seat cover, seat or main body
unit. This can damage or break
the unit.
Prohibited
ᆞDo not use a broken product.
ᆞAs the unit is a bathroom appliance,
do not use it for any other purposes.
Prohibited
Do not slam or close the seat
or seat cover forcefully.
Prohibited
Prevent children from putting
foreign substances or inserting
their hands into the dryer outlet
or onto the nozzle.
Prohibited
Do not let urine contact the
dryer outlet or nozzle area.
Observe at all times
Never put the product
in water.
Prohibited
Do not pull the
connecting hose
forcefully or bend it.
Prohibited
When cleaning or not
using the product over a
long period of time, be
sure to unplug the unit.
Observe at all times (refer to page 19)
When the following people sit down on the seat, a guardian should pay extra
attention so that they will not fall
when sitting on the toilet seat or standing up from it.
– Children, elderly, or those who cannot independently sit or stand on the
seat.
E
N
G
L
I
S
H
SB-1000.indd 7 2019-02-15 오후 2:04:51
Warm air dryer
Different types
of nozzles
(refer above)
Skin sensor is
imbedded in seat
Drain / Unit
Separation Button
Heated seat
Lid
Caution label
TURBO
FEMININE
POSTERIOR
8
4 Product structure and designations
Cone packing
(2pcs)
Nuts (2pcs) Bolt Case
(2pcs)
Water supply hose
(for electrical toilet seat)
T-Valve &
packing
Water supply hose
(for toilet flush water tank)
User manual
Quick guide
(for installation)
Mounting bolts
(2pcs)
Base Plate
(1pcs)
Conversion Nut
1/2” Compression
(With Packing)
Main unit
Product components
Q
For plumbing For product fixation Installation instructions
Remote control
1.5V AAA type
Battery (2pcs)
For remote control
Remote control holder
SB-1000.indd 8 2019-02-15 오후 2:04:54
ᆞAlways sit on the middle of the unit and do not sit on the side of the seat.
(The basic functions will not work if the skin sensor is not active.)
ᆞWhen operating FEMININE / POSTERIOR / TURBO, if the water temperature is low
and
cold water comes out after using it for a period of time, pause and wait for 3
minutes for warm water to be provided.
ᆞDrying will occur quicker if toilet paper is used to wipe away excess water
prior to using the dryer function.
STOP Stop
TURBO For Her Back Wash
FEMININE
POSTERIER
OSCILLATE
ENERGY
SAVER
WATER
DRYER
NOZZLE
POSITION
WATER
SEAT
For Her Front Wash
For His Back Wash
When selected, a light will show on the
control panel which can be controlled by the +
or – buttons.
Pressing Energy Saving on or off activates or
deactivates the Energy Saving mode.
The water pressure and dryer temperature can be
adjusted up to 5 levels.
The oscillating mode and nozzle position can be
adjusted up to 5 levels.
The water temperature can be adjusted up to 4
levels.
The seat’s temperature can be adjusted up to 4
levels.
9
Remote control
Sitting on the heated seat or using the dryer for an extended period of time
can potentially cause low degree burning.
Special precautions should be taken for children, those who cannot adjust the
temperature, and those who have sensitive skin.
E
N
G
L
I
S
H
DRYER
Pressing any of these buttons a second time will
automatically oscillate the nozzle back and forth for a
wider wash. Pressing it once more will stop the
oscillation.
Caution
If the remote con trol is not used is not used for
10seconds,the LED lamp will turn off automatically to
protect the basttery life.
SB-1000.indd 9 2019-02-15 오후 2:04:55
Check the water valve in the bathroom. You may need to consider purchasing
additional components.
For the following below case, the T-valve and conversion nut included alone
should be
Minus home Handle Inner bolt for water valve
■ Water supply valve ■ Inner bolt water valve
ᆞPlease consult with a qualified specialist.
ᆞPlease put the unused water hose in a secure area.
■ Professional engineering is needed for plumbing
work on specialized water pipes and flush valve pipes.
ᆞThis product requires 120V usage.
ᆞPlease do not plug in the electrical cord prior to installation.
ᆞPlease consult with a licensed electrician if electrical work is needed, and
in case a grounded outlet
is not available, grounding should be done in order to prevent short circuits
or electric shock.
ᆞPlease contact our service
center(1-800-515-3430) when you want to
reinstall the bidet product(move or replacement).
Caution
Shut water supply by turning it to the
right and detach the water hose.
Water supply hose
Water valve
Remove existing seat and lid.
ᆞunscrew the bolts the bolts
on both sides of the
existing toilet seat to
remove the seat
and lid.
ᆞStore the removed seat,
nut and water hose in a
safe area in case you
move or it needs to be
reinstalled.
Connect the water supply hose to the
T-valve. Insert the packing in the T-valve.
Connect the water supply hose to the
assembled T-valve.
Conversion Nut
(with packing)
T-valve
(with packing)
If the water supply hose is old or
damaged please replace it with
the water supply hose included
with the unit.
※ If the water supply valve opening is 1/2 inch please use
a conversion nut to connect it with the T-valve.
※ Included 1/2″ conversion nut is OD Compression, not FIP.
※ T-valve packing must be used to prevent water from leaking.
Nut Toilet
body
Exisiting toilet seat
10
5 Installation
Check the water valve
Installation steps
SB-1000.indd 10 2019-02-15 오후 2:04:55
Once the base plate is attached to the
unit, align the unit and toilet fixture facing
front, and then insert the mounting bolts
to the toilet mounting holes.
Put the bolt into the bolt case and align
it with the top of the base plate. Insert
bolt with bolt case onto the base plate.
After this is done hold the bolts, slide it
into the bottom of the unit until it snaps
in place.
Install the main unit and insert the
mounting bolts to the toilet mounting
holes.
Connect the flexible tube from side of
T-valve to the unit. Turn the water valve
to the left to allow water to flow.
Installed bolt case
Bolt
Bolt
Back
Base plate
Cone Packing
Nut
Water supply valve
Water supply hose for
electronic toilet seat
11
Cone Packing
Nut
E
N
G
L
I
S
H
※ Customers should use the new hose set provided with the product.
Do not use used set again.
SB-1000.indd 11 2019-02-15 오후 2:04:56
Turn the water valve to the left and see if there is any water leaking from
the hose.(~)
Connect the power cord to the 120V electric outlet.
ᆞIf the power light does not appear after plugging in the electric cord,
press any button on the remote control.
ᆞIf you hear a ‘beep’ sound, then the lights will appear on the
power lamp.
ᆞIn order to check whether the functions work, you will first need to touch
the seat or sit on it to
activate the skin sensor.
ᆞPlease be aware that water will come out. This product can only operate when
the user sits on the
electronic toilet seat.
ᆞIf the tank is full, then a low beeping sound will occur which indicates that
preparation is complete.
If you press or button, the water will begin to enter the heated water tank.
Function Check
Water supply valve
12
6 Initial Operation
SB-1000.indd 12 2019-02-15 오후 2:04:57
※ Please follow the instructions below when moving or separating the unit from
the toilet for cleaning purposes
Unit separation
button
Unit separation button
Disconnect the power plug
Unplug the T-valve from the water supply. (Refer to page 10~11)
Connect the water hose to the toilet directly and turn the water valve to the
left to open it.
See if there is any leaking from the water hose connection.
Install the new toilet seat and lid.
Shut the water supply valve
Push and hold the button on the right side of the unit
to completely drain the water from the water tank.
Loosen the nut on the hose that is connected to the
unit, and then separate the electronic toilet seat from
the toilet in the following order as illustrated.
ᆞWhile pushing the button (area shown as an arrow) push the electronic toilet
seat slightly toward to the
front and then the body unit will begin to slide out.
Next, lightly pull the unit toward the front and it will detach from the
toilet.
ᆞAs explained above, steps 1~4 are instructions for separation of the unit for
basic cleaning purposes,
and steps 5~7 are instructions for separation when moving, etc.
Do not turn the seat upside-down. This can cause damage to the unit as well as
fire hazard.
13
7 Separation of unit from the toilet bowl
E
N
G
L
I
S
H
SB-1000.indd 13 2019-02-15 오후 2:04:57
Please press or ,
ᆞSit on the toilet seat so that the skin sensor can fully be activated.
ᆞWash is available FEMININE, POSTERIOR, TURBO.
ᆞThe selected function can be used for up to 1 minute.
Press
ᆞThe display light for the (high), (low) on the remote will turn on while the
dryer is activated.
ᆞThe selected function can be used up to 3 minutes.
ᆞBefore using the dryer, wiping the wet area with toilet paper will let drying
occur more quickly.
Press
ᆞFEMININE, POSTERIOR, TURBO wash or drying will all stop.