FLAWNT F80216M Electric Pressure Washer User Manual

June 1, 2024
FLAWNT

FLAWNT F80216M Electric Pressure Washer

FLAWNT-F80216M-Electric-Pressure-Washer-PRODUCT

Specifications:

  • Product Name: Electric Pressure Washer
  • Model: JMG-80216M
  • Intended Use: Domestic
  • Power Source: Electric
  • Applications: Vehicles, machines, buildings, facades, driveways, decks, sidewalks, garden furniture, various surfaces

Product Usage Instructions

Safety Instructions:

General Safety:

  1. Stay alert and operate the pressure washer away from bystanders, pets, and children.
  2. Avoid unintentional starting; ensure the machine is off before connecting to power.
  3. Use safety gear such as glasses, gloves, and non-slip footwear.
  4. Never use hot water with the machine; only connect to a cold water supply.

Electrical Safety:

Ensure any extension cords used are suitable for outdoor use and in good condition. Connect the machine to a power supply with residual current device (RCD) protection. Protect all electrical connections from water and moisture.

Usage Precautions:

  • Never direct the spray towards people, animals, or electrical devices.
  • Use only detergents recommended for pressure washers.
  • Do not allow the unit to run dry or without a stable water supply.
  • Ensure all connections are secure and free from damage before operation.

Storage and Maintenance:

Store the machine in a frost-free area to prevent damage. Use a pump protector for cold weather storage. Regularly inspect and maintain the machine to ensure safety and efficiency. Always turn off and disconnect the machine when not in use or before any maintenance.

Shutting Down & Breaks:

To shut down, turn off the machine and disconnect the power and water supply. Release pressure from the system. For breaks longer than five minutes, ensure the machine is off and disconnected.

Winterizing & Long-Term Storage:

Properly drain and protect the machine with non-toxic antifreeze if temperatures fall below freezing. Before re-use, ensure the system is thoroughly flushed of any antifreeze. By following these instructions, operators will ensure a safer working environment and prolong the lifespan of the pressure washer.

FAQ

Q: Can I use hot water with the electric pressure washer?

A: No, only connect to a cold water supply as using hot water can damage the machine.

Q: How should I store the pressure washer in cold weather?

A: Store in a frost-free area and use a pump protector to prevent damage during cold weather storage.

Q: What should I do before long-term storage of the pressure washer?

A: Properly drain and protect the machine with non-toxic antifreeze if temperatures fall below freezing, and ensure thorough flushing before re-use.

CUSTOMER SUPPORT:
flawnt-customercare@outlook.com

WARNING: Read the instruction before operation.

This machine is designed for domestic use only! Commercial or industrial use are prohibited.

Product Description

This electric pressure washer is designed for versatile use, offering powerful cleaning capabilities for vehicles, machines, buildings, facades, driveways, decks, sidewalks, garden furniture, and various surfaces. It ensures efficient and thorough cleaning results , making it a valuable tool for a wide range of applications in residential settings.

Safety Instruction

All Operators Must Read These Instructions Before Use

  • WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
  • CAUTION: Indicates a hazardous situation which, if not avoided, might result in minor or moderate injury.
  • DANGER: Indicates an imminent hazardous situation which, if not avoided, will result in death or serious injury.

General Safety:

WARNING: This appliance is not intended for use by children or individuals with reduced physical, sensory, or mental capabilities. Ensure supervision to prevent any mishandling. Before operation, inspect the machine for any defects. If defects are found, do not use the machine and contact customer service.
(flawnt-customercare@outlook.com)

WARNING: Always follow basic safety precautions while operat-ing the pressure washer to reduce the risk of fire, electric shock, and personal injury. This includes understanding the machine, keeping a safe distance, using appropriate attire, and maintaining a stable position.

Operating Instructions

  1. Stay alert and sober. Operate the pressure washer away from bystanders, pets, and children.
  2. Avoid unintentional starting. Ensure the machine is off before connecting to power.
  3. Use safety gear, including glasses, gloves, and non-slip footwear.
  4. Never use the machine with hot water. Only connect to a cold water supply.
    WARNING: Do not operate the machine if the power cord or other important parts are damaged. Contact authorized service for repairs. Disconnect the machine from power supply before any maintenance or repair.

Electrical Safety:
Ensure any extension cords are suitable for outdoor use and are in good condition.The machine must be connected to a power supply with residual current device (RCD) protection.

WARNING: Protect all electrical connections from water and moisture.

Usage Precautions:

WARNING: Never direct the spray towards people, animals, or electrical devices. Use only detergents recommended for pressure washers.

CAUTION: Do not allow the unit to run dry or without a stable water supply. Ensure all connections are secure and free from damage before operation.

Storage and Maintenance:

Store the machine in a frost-free area to prevent damage.

CAUTION: Use a pump protector for cold weather storage to avoid damage. Regularly inspect and maintain the machine to ensure safety and efficiency. Always turnoff and disconnect the machine when not in use or before any maintenance.

Shutting Down & Breaks:
To shut down, turn off the machine and disconnect the power and water supply. Release pressure from the system.
For breaks longer than five minutes, ensure the machine is off and disconnected.

Winterizing & Long-Term Storage:
Properly drain and protect the machine with non-toxic antifreeze if temperatures fall below freezing.

WARNING: Before re-use, ensure the system is thoroughly flushed of any antifreeze. By adhering to these instructions, operators will ensure a safer working environment and prolong the lifespan of the pressure washer. Always consult the full manual and contact cus-tomer service for any uncertainties or issues.
flawnt-customercare@outlook.com

Konw Your Electric Pressure Washer

FLAWNT-F80216M-Electric-Pressure-Washer-FIG-1

  1. Pressure water sprayer
  2. Trigger
  3. Safety lock
  4. High-pressure hose connection
  5. Pressure water sprayer holder
  6. Stainless steel lance
  7. Wheel*2
  8. Spray wand protector
  9. Water outlet (high-pressure connection)
  10. Water Inlet (garden hose connection)
  11. On/Off switch
  12. Transport handle
  13. Cord holder
  14. Detergent Tank
  15. Power cord with GFCI
  16. High-pressure hose
  17. Garden hose adapter
  18. Needle clean-out tool
  19. 0º Quick-Connect nozzle (red)
  20. 15º Quick-Connect nozzle (yellow)
  21. 25º Quick-Connect nozzle (green)
  22. 40º Quick-Connect nozzle (white)
  23. Foam Cannon
  24. Screws*5

Assembly

  1. Position the washer as CLOSE as possible to the water supply.
  2. Slide the pressure water sprayer holder and cord holder into the positions (Fig.1).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-2
  3. Tighten the transport handle with two screws ( Fig.2 ).
  4. Slide the handle into place and fasten it securely using two screws (Fig.3 ).
  5. Align the spray wand protector with the screw hole on the case and secure it with one screw ( Fig.4 ).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-3
  6. Insert the Stainless steel lance into the pressure water sprayer and ensure both parts are fully locked together (Fig.5).
  7. Insert the desired nozzle onto the spray wand (Fig.6).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-4 Tips: 1.Nozzle Type

FLAWNT-F80216M-Electric-Pressure-Washer-FIG-5

TIPS: 2.Install The Foam Cannon

  1. Remove the foam cannon cap and then fill the foam cannon with detergent designed specifically for use with pressure washers (Fig.7).
  2. Recap the foam cannon and attach it to pressure water sprayer (Fig.8).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-6
  3. The foam cannon is featured with a foam-volume adjustable knob. Follow the instructions as shown to use the foam-volume adjustable knob (Fig.9).
  4. Connect the high-pressure hose to pressure water sprayer (Fig.10).
  5. Connect the high-pressure hose to the water outlet on the washer (Fig.11).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-8
  6. Connect the garden hose adapter (female coupler) to the water inlet of the pressure washer, then thread your garden hose (male end) into the garden hose adapter (Fig.12).
  7. Connect the garden hose to the water supply (Fig.13).FLAWNT-F80216M-Electric-Pressure-Washer-FIG-9
  8. Plug the power cord into the power source (Fig.14).
    Note: The GFCI may need to be reset when first plugged into the elec-tric outlet. Press the “Reset” button until the power light indicator on the GFCI illuminates.

Operation

Start Up

  1. Turn the water supply tap on completely

  2. Turn on the switch.
    Note: Ensure that the switch is in the OFF position before plugging the unit into the power outlet (Fig.15).

  3. Press the trigger and start pressure water sprayer (Fig.16). When the flow is steady, Engage the safety lock on the trigger handle by pushing up on the safety lock until it clicks into the slot.
    Note: Before start , please make sure the safety lock is in the original position, then press the trigger for a few seconds until water flow is steady. This will allow air to escape and discharge any residual pressure in the hose .FLAWNT-F80216M-Electric-Pressure-Washer-FIG-11

Shutting Down

  1. Turn the switch to the OFF position and unplug the power cord from the outlet.
  2. Turn off the water source.
  3. Hold the trigger to release water pressure.
  4. Disconnect the garden hose from the water inlet on the unit.
  5. Disconnect the high-pressure hose connection on the pressure water sprayer handle .
  6. Release the trigger and engage the sprayer safety lock.

Working with Detergent Tank
Remove the detergent tank cap with detergent suction tube from the detergent bottle and press the detergent into the detergent tank (Fig.17).
Note: The device is under low pressure when using detergent and pulling out spray lance.

Technical Specification

Rated Voltage 120V ~ 60 Hz
Motor 14.5 amp
Water Inlet Temperature 32°F-104°F/0- 40°C
Max Water Inlet Pressure 0.4 MPa
Maximum Pressure 2030 PSI
Maximum Flow Rate 2.5 GPM
Hose Length 26 ft(8 m)
Power Cord Length 16 ft (GFCI Protected)
Foam Cannon Capacity 0.5L
Net Weight 18.96 LB

Maintenance and Care

CAUTION! Before working on the pressure washer, disconnect the plug from the power supply socket.

  1. Clean the nozzle using the needle clean-out tool provided (Fig. 18). Remove the spray wand from the sprayer, clear any debris from the nozzle hole, and rinse it
  2. Remove any remaining debris by back flushing water through the nozzle and spray wand. To do this, position the end of your garden hose (with water running) against the nozzle’s tip, expelling water and debris from the rear opening of the nozzle and spray wand.

Troubleshooting

Notice: Disconnect the unit from power before performing maintenance or checking its parts.

Problems Possible Cause Possible Solution
Machine refuses to start 1.power cord is not plugged in. 2.Defective socket.

3.Fuse has blown. 4.Defective extension cord.

| 1. Connect the power cord to the power supply.

2. Check the power cord and reset the GFCI or try a different outlet.

3. Replace fuse. Switch off any other machines that are using the same circuit.

4. Try the unit without an extension cord.

Fluctuating pressure| 1.Pump sucking air. 2.Valves dirty, worn out, or stuck.

3.Pump seals worn out.

| 1. Check the hoses and connections are airtight.

2. Clean or replace valves/seals.

Problems Possible Cause Possible Solution
Machine stops 1.Fuse has blown. 2.Incorrect mains voltage. 3.Thermal sensor
activated. 4.Nozzle partially blocked. 1. Replace fuse. Power down other

machines on the same circuit.

2. Verify the mains voltage matches the model specifications.

3. Allow the washer to cool for 5 minutes. 4.Clean the nozzle.

Fuse blows| 1.Air in inlet hose. 2.Inadequate supply of mains water.

3.Nozzle partially blocked. 4.Water filter blocked.

5.Hose kinked.

| 1. Keep holding the trigger until normal working pressure returns.

2. Ensure the water supply matches the required specifications.

3. WARNING! Avoid using long, thin hoses.

4. Clean the  nozzle. 5.Clean the water inlet filter.

6.Straighten the hose to clear any kinks or blockages.

Machine often starts and stops by itself| 1.Pump/sprayer is leaking. 2.Trigger mechanism is broken.| Please mail:

flawnt-customercare@outlook.com for assistance.

Machine starts, but no water comes out| 1. Pump/ hoses or accessories frozen .

2. No water supply. 3.Water inlet filter blocked. 4.Nozzle blocked.

| 1. Allow pump, hoses, or accessories to thaw.

2. Connect inlet water. 3.Clean the water inlet filter. 4.Clean the nozzle.

Customer Support

Email:
flawnt-customercare@outlook.com

Hours:
Monday – Sunday, Response within 12 hours

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals