burgbad M1142 Eqio Mineral Cast Washbasin with Base Cabinet Instruction Manual

burgbad M1142 Eqio Mineral Cast Washbasin with Base Cabinet

Specifications:

• Brand: Eqio
• Model: M1142
• Manufacturer: burgbad GmbH
• Address:  Str. 15, D-91171
• Contact: T +49 (0) 84 63-901-0, info@burgbad.com, www.burgbad.com

Product Usage Instructions

Assembly Instructions:
Below are important instructions for installing and handling the bathroom furniture:

• Read and make note of all instructions before installing the furniture.
• Products should be installed by a specialist craftsman for sanitary facilities or a competent person.
• Electrical installations must be done by a specialist following DIN 57100/VDE 0100 Part 701.

Installation Guidelines:
Ensure the following during installation:

• Check for damages on the products before installation.
• If significant damage is noticed, still make preparations for installation.
• Use appropriate fastening materials designed for load-bearing walls.
• Attach products at all installation points provided.
• Ensure drywalls and plasterboard walls have adequate load-bearing capacity.

Maintenance and Care :
After installation, remember the following:

• Adjust doors and drawers as part of normal maintenance.
• Check water and siphon connections for tightness regularly.
• Clean the furniture before handover by removing dust, labels, and residues.

Cleaning Instructions:
For high gloss surfaces:

• Surfaces fully harden within three weeks of protective film removal.
• Treat with care during this period; do not clean or wipe them (no microfiber cloth).
• Do not remove the protective film until furniture set is fully installed.

Preventing Water Penetration:
To prevent water from entering between the wall and wash basin:

• Seal the connecting edge to the wall with a neutral silicon joint.
• Use only solvent-free silicon for sealing.

FAQ :

• Q: Can I install the products myself?
  A: Products should be installed by a specialist craftsman for sanitary facilities or a competent person. Electrical installations require a specialist.

• Q: What should I do if I notice damage on the products?
  A: If damage is noticed, products should still be installed if possible. Make preparations for installation even if a part cannot be installed due to significant damage.

MONTAGE- UND BEDIENUNGSANLEITUNG FITTING INSTRUCTIONS AND OPERATING MANUAL MANUEL DE MONTAGE ET D‘UTILISATION MONTAGE

• burgbad GmbH, Grafenberg, Morsbacher Str. 15, D-91171 Greding T +49 (0) 84 63-901-0
• info@burgbad.com,
• www.burgbad.com

 ASSEMBLY INSTRUCTIONS

• Below you will find important information for installing and handling bathroom furniture, as well as safety instructions. It is essential that you read and make note of these before installing the furniture. We can accept no responsibility for damages that are the result of failure to adhere to these instructions.
• Our products may only be installed by a specialist craftsman for sanitary facilities or by another competent person. Electrical installations may only be conducted by a specialist, taking DIN 57100/VDE 0100 Part 701 into account. Plug connections, lighting and sockets must be checked.
• If you notice damage on the products, they should still be installed. If a part cannot be installed due to significant damage, all preparations for installation should still be made and the installation rails, hooks and hanger bolts should be attached. Our factory customer service does not undertake drilling.
• The fastening materials (screws, wall plugs) are designed for solid, sufficiently load-bearing walls. In other installation situations, special fastenings must be used accordingly.
• Hanger bolts 1 are not included in the delivery!
• The products must be attached at all the installation points provided. The installation dimensions refer to the top edge of finished flooring. All dimensions in mm.  Drywalls and plasterboard walls must have an adequate load bearing capacity.
• No drilling dust can be allowed onto the pull-out rails! Furniture should therefore only be hung after drilling, or taken down again before drilling. Vacuum up or rinse off any  drilling dust; never wipe it from the washbasin. Do not place any tools or sharp-edged or heavy objects on the washbasin.
• In order to prevent water from penetrating between the wall and the wash basin, the connecting edge to the wall must be sealed with a silico-ne joint. Use only neutrally bonded (solvent-free) silicon.
• High gloss surfaces are fully hardened within three weeks of the protective film being removed. Please treat them with particular care during this period and do not clean or wipe them (no microfiber cloth). Do not remove the protective film until the furniture set has been fully installed.
• Doors and drawers must be adjusted after installation. This subsequent adjustment is part of normal maintenance depending on the use and loading of the items of furniture and is  not a reason for complaint. Check the water and siphon connections for tightness! Please clean the furniture before handover! Remove drilling dust, labels and adhesive residues! The function, handling and care of the products must be explained to the owner.

PREPARATIONS FOR FITTING

MIRROR CABINET

IMPORTANT FITTING ADVICE

ILLUMINATED MIRROR

VANITY UNIT I HEAVY LOAD HANGER

GLASS WASHBASIN

EN IMPORTANT FITTING ADVICE – GLASS BASIN
The outlet and tap should not be fitted too tight during installation. Note: Danger of cracking. To avoid stress cracks, a permanently flexible sealing compound (installation putty) should be used between the valve and the glass when fitting the outlet valve from above. For taps, always fit a rubber seal between the glass and the metal fitting. For sealing use only a transparent, solvent free silicon. Solvent-based silicons can damage the colour coating of the basin.

CERAMIC WASHBASIN

BASIN

GUEST BATH

RACK

DRAWER I PULL OUT DRAWER I ADJUSTMENT

DOORS ADJUSTMENT

• ADJUSTMENT OF DAMPER
• COVERS

FITTING INSTRUCTION

REPLACEMENT OF ILLUMINANT

• SPGS
• SPGT
• SIGZ
• SEZQ
  • These products contain a light source of energy efficiency class G
• SIGP
  • These products contain a light source of energy efficiency class F

REMOVAL AND DISPOSAL

• Recycling or disposing of electrical appliances.
• Never dispose of electronic equipment in your household waste. Observe the regulations applicable in your area.
• Risk of electric shock! Touching live parts can cause serious injury or death. Removal and repairs should only be carried out by a qualified electrician.

REMOVAL AND DISPOSAL

At the end of its useful life, your old furniture can be disposed of at your local recycling point. Please observe any local regulations.

CARE INSTRUCTIONS

The bathroom furniture is design for a long service life in the bathroom. We ask that you follow the instructions below to ensure that you can enjoy our high quality products for many years:

1. The installation of a shower wall is essential if the furniture is installed directly next to the tub/shower area
2. Ensure sufficient ventilation (windows, ventilator)
3. Avoid or immediately mop up overflowing water

Cleaning the bathroom furniture, mirrors and glass surfaces, mineral cast and ceramic:
We recommend a clean, soft, damp cloth (no microfiber cloth!) for gently cleaning wood, plastic, painted and ceramic surfaces. Particularly stubborn stains (oils, cosmetics etc.) should be removed immediately. This can be done without residue using 1% soapy water or fine washing-up liquid. Then rub the surface dry. Take care that no droplets of residue remain on the edges and backs. No scouring agents or care products containing alcoholic substances should be used to clean high gloss surfaces.

• High gloss surfaces are fully hardened within three weeks of the protective film being removed. Please treat them with particular care during this period and do not clean or wipe them.
• In the case of heavy soiling on mineral cast, ceramic or glass, please use a mild liquid cleaner (without alcohol or cream cleaner) such as the vinegar-based cleaner from Frosch, with warm water. Please ensure that the water is not hotter than 65°C. Do not allow these premium materials to come into contact with hard or sharp-edged objects. Do not place hot objects on the plates! In order to retain the sheen of the mineral cast surface, we recommend applying a high quality car polish such as SONAX Xtreme Polish & Wax 2 Hybrid NPT and polishing it from time to time.

References

• burgbad international | burgbad

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>