POPRHINO SSZ-CWMSP01-SBN Smart Cat Litter Box User Manual

POPRHINO SSZ-CWMSP01-SBN Smart Cat Litter Box

Product Information

Specifications:

• Product Name: Smart Cat Litter Box
• Usage: For indoor use only
• Weight Limit: Kittens weighing less than 1 kg and lactating cats should not use auto-cleaning mode
• Power Source: Original power adapter
• Caution: Do not soak or immerse the host part of the device

Product Usage Instructions

Cautions:

1. Install and use the device strictly according to the instructions.
2. Use in an indoor environment, avoid direct sunlight and keep away from fire sources.
3. Place the device on a flat and hard ground without placing items on top.
4. Avoid dragging or placing vigorously to prevent damage.

Instructions for the First Use:

1. Unpacking: Cut the tape from the bottom of the carton and place the machine on a flat ground.
2. Placement: Ensure all four feet of the product are in contact with the ground.
3. Accessories: Adapter, Manual, Garbage bag (1 roll)

Add Litters:
Ensure the levelled litter height is between the MAX line and MIN line. Adjust the amount of sand as needed.

Usage:

1. Power On: Use the adapter and wait for self-check for 3-8 minutes.
2. Cleaning: The product will automatically clean up clumped cat excrement after the cat leaves.
3. Smell Cleaning: The product will automatically start the smell cleaning function after cleaning.

FAQ:

Q: What should I do if the product self-check takes longer than 8 minutes?
A: If placed in a narrow space or there is an infrared interference source, self-check may take longer. Please wait patiently.

FOR THE FIRST USE

1. Please place the machine on firm and flat ground.
2. Please add litter no higher than the MAX line after placing the machine well.
3. Please power on the machine and wait for it to finish self-check. Then it is ready for the at to use.

Cautions:

1. Please install and use this device strictly according to the instructions.
2. Please use it in an indoor environment, do not place it in direct sunlight, and keep it away from fire sources.
3. Please place the device on a flat and hard ground, and do not place articles on the top of the device.
4. Do not drag or place vigorously during placement to avoid device damage.
5. Kittens weighing less than 1kg and lactating cats should not use the auto-cleaning mode of the device.
6. It is strictly forbidden to soak or immerse the host part of this device.
7. Please unplug the power cord when moving, cleaning the device or not using it for a long time.
8. Please use the original power adapter to avoid damage to the device or potential safety hazards.
9. If children use this device, please make sure to use it under the guidance of an adult.
10. Please perform maintenance under the guidance of professionals to avoid all kinds of damage.
11. If you encounter product use problems, please contact customer service.
12. Please read this manual carefully before. Once installed and used, it means that you have carefully read and accepted the following safety instructions.
13. If the product does not work properly due to other unknown conditions, and you do not have time to refer to the instructions, please restart the power.

INSTRUCTIONS FOR THE FIRST USE

Unpacking:
Turn over the carton to cut the tape from the bottom, then turn over back the carton to pull up the carton vertically.

Placement:
Place the machine on the flat ground and make sure all four feet of the product are in contact with the ground. Items with a height of more than 5CM shall not be placed within 30 in front of the product, so as not to affect the cat identification sensor outside the product.

Notice:

• The four feet of the product must be in contact with firm flat ground!
• Place the machine on the soft carpet.
• Place the two front feet of the machine on the cat litter mat or carpet.

Accessories

Accessories(in litter storage box):

• Adapter*1
• Manual*1
• Garbage bag(4550mm)1(roll)

Notice:
Please observe the installation method of garbage bags, or scan the code below to watch the video.

Add litter sand:
Make sure the levelled litter height is between the MAX line and the MIN line. (The amount of sand can be adjusted according to the actual situation.)

Use:

• Power on with an adapter and wait for the machine to self-check for about 3-8 minutes. It will automatically enter the state of sensing after self-check, no need to change its program.
• After the cat leaves, the product will automatically clean up the clumped cat excrement in about 3 minutes, and last for 4 minutes.
• After cleaning, the product will automatically start the smell-cleaning function, and last for 30 minutes.

Notice:

• ×Pick up or drag the product after powering up. (This will interfere with weight calibration in the reset program.)
  1. If you place the product in a narrow space or there is an infrared interference source in front of the product, the product self-check may take about 8 minutes. Please wait patiently.
  2. If the product detects that the space is not suitable for its infrared sensor to work, the infrared detection function will be automatically disabled after the self-check is completed., However the weight detection system inside the product will assume the judgment work of whether the cat enters.
  3. During the clearing process, all keys are suspended. If you need to perform other functions, please wait until the clearing process is complete.

APP

Overseas users

• Method 1: You can scan the above icon with your mobile phone
• Method 2: You can download the download “Tuya” App and install it before arching it in the App Store.

Networking:

1. Confirm that the phone is connected to 2.4G WiFi, then turn on Bluetooth and Location.
2. Press “Auto” for 2 seconds, WiFi indicator begins to flash, so the machine begins to wait for the network.
3. Open your phone App to add equipment or scan automatically.
4. Continue “Next” after scanning the machine.
5. Continue “Next” after inputting the WiFi code and wait to connect.
6. Enter the APP after connecting.

Notice:
If the network configuration fails or a timeout message is displayed, check the following possibilities:

1. Whether WiFi, Bluetooth, and Location switch are enabled at the same time.
2. Whether the WiFi is in the 2.4G band and whether the phone is connected to the 2.4G band WiFi network. (The product cannot recognize the 5G band network.)
3. Whether the WiFi indicator on the panel is flashing during network configuration.
4. Whether the WiFi network in your home is faulty or down, please check whether other devices can use the network normally.
5. Whether the WiFi password is correct.
6. Whether the WiFi signal is too bad, please move the machine to a nearby router and reconnect.
7. The router connects to many wireless devices, causing IP address conflicts.

OPERATING INSTRUCTIONS

Auto:
Click“ Auto” on the panel or on the App to start auto-sensing for cats in and out. (It will open automatically after the product is powered on and self- checked.)

Notice:

1. Please click“ Auto” on the panel or on the App to close auto-sensing, if you have kittens less than 1kg or the cat is pregnant. Then click“ Clean” by your hand according to the actual use of the machine.
2. If you are using litter that clumps quickly, you can adjust the “cleaning wait time” in the App, such as 1 minute, to clean the litter as quickly as possible and reduce the smell. If you are a multi-cat family, you can adjust the “cleaning interval” in the App, for example, 30 minutes, to avoid repeated ineffective cleaning of the product.
3. If the cat enters the bin for more than 10 seconds, the cat is judged to have potty behaviour. After the cat leaves for 3 minutes, the automatic cleaning procedure will be performed. (The default interval between cleanups is 15 minutes to prevent the product from being started too frequently during multiple cat use. If the machine doesn’t work after your second cat pees, it may be because the interval between these two pees is less than 15 minutes.)
4. The button on the App cannot be closed/opened or synchronized with the panel temporarily, please check the network status or re-configure the network, or click the corresponding button on the App and repeat once or twice.

Clean:
Click“ Clean” on the panel or on the App to start clearing immediately.

Notice:

1. During the clearing process, all keys are suspended. If you need to perform other functions, please wait until the clearing process is complete.
2. Prolong the waiting time for cleaning in the phone App when the cat has diarrhea, to allow the cat litter to take enough time to clump and reduce the pollution of soft feces in the ball bin.
3. If you have restarted the machine, the waiting time of the “ Clean” procedure will be restored to the default value of 3 minutes, which can be reset in the APP if necessary. (setting range: 0 to 60 minutes)
4. Prolong the interval time between two clearings when you have multiple cats, to prevent repeated cleaning of products.
5. If you have restarted the machine, the interval time between two clearings will be restored to the default value of 15 minutes, which can be reset in the APP if necessary. (setting range: 0 to 120 minutes)

Add cat litter:

• Method 1:
  In“ Auto” mode, when the adding cat litter is more than 1kg, the “Auto” will flash. After 30 minutes, the cat litter will be automatically smoothed and the weight will be automatically calibrated. If you think 30 minutes is too long to wait, please long press the“ Remove odour” button for 2 or more seconds. The sand will be smoothed immediately and the weight will be calibrated immediately.

• Method 2:
  Power off the machine, then power it on again after adding sand.

Notice:

1. The machine won’t stop when it is smoothing and even a cat enters it at this moment. But don’t worry. The machine only swings at some angles, this swing won’t hurt the cat. (Besides this situation, the machine has a protection function. It will stop immediately once the catwalks close to the entrance during clearing.)
2. Please make sure the height of the sand is between the MIN line and the MAX line after adding. If not, please adjust it with method 2.
3. You can find the sand surface correction option on the App to adjust the position of the sand. (In grade 0, the sand surface is tilted to the right, and in grade 6, the sand surface is tilted to the left.)

Replace litter：

1. Replace the garbage bag with an empty one (to avoid that the original one is already full of litters);
2. Make sure the rest sand is close to the MIN line (to avoid overflow when the bin rotates);
3. Press“ Replace Litter” for 2 seconds, then wait for the machine to clear the rest sand;(about 3 minutes)
4. Replace the garbage bag with an empty one again after clearing the sand;

Notice:

1. Click“ Replace Litter” again to cancel if you click it by mistake or if you find you have forgotten to replace the garbage bag first.
2. For fine mineral sand, when replacing the bag（step ①）, to avoid the overflow of mineral sand from the mouth of the bag, you can first press “Clean” for 2 seconds; then the litter bin will rotate 90° counterclockwise to ensure that the mouth of the bag is upward when replacing. After bag replacement, repeat ③ and ④.

Remove Odor:

• Method 1:
  Click“ Remove Odor” on the panel or click“ Odorless” on your phone App.

• Method 2
  Set regular work on your phone App.

Notice:

1. The machine will remove odour automatically for 30 minutes after every clearing.
2. It will stop automatically once the cat enters in, continues to work after the cat leaves.

Replace garbage bag:
When the indicator“ Full” lights up, you need to replace the garbage bag.

Notice:

1. The“ Full” prompt is only a reference value. When using different types of cat litter, its volume, density and fluidity will affect the judgement of the “ Full” prompt. In the APP, you can adjust the delay of the “ Full” prompt according to your use. The default value is 0(there is still a little space in the bag for garbage), and the maximum value can be adjusted to 15.
2. If you have restarted the machine, the delay of the “ Full” prompt will be restored to the default value, which can be reset in the APP if necessary.
3. Normally, the storage capacity of one cat can reach 15 days, and three cats can reach 5 days. Users can replace the garbage bag every 5 days depending on the number of cats or temperature conditions.

Wash bin:

1. Please power off the machine first！
2. Open the buckle of the barrel compartment, and lift the bin.
3. Dry the bin before loading it back to the base！

Notice:
If the indicator of the bin sign lights up, please restart the machine or click” Clean” to make it clear

Lock the keyboard:
Hold down“ Auto” +“ Remove Odor” for more than 2 seconds, or click the “Child Lock” on the app to enable or disable the child lock function.

Close or open infrared sensor:
When the cat litter box is placed in a cage or a narrow space, please hold down “Clean” +“ Replace litter” for more than 2 seconds, or click the bucket infrared sensor option in the APP to turn off or on the bucket infrared sensor to prevent the machine from always judging wrongly.

Timing:

Sleep mode
When a cat litter box is placed in the bedroom, you can set in the App“ Do not Disturb Timing” to prevent the night-time activation from disturbing sleep.

Notice:

1. During the DND period, the light on the panel will be off. Touch any button to exit the DND mode immediately.
2. If the product is clearing when setting DND, the machine will enter the DND state after the cleaning is complete.

Timing:

1. Regular clean-up mode
   Set the machine to clean regularly in the App“ Clean Timing”.

2. Timing net flavour
   Set the machine to remove odour regularly in the App“ Deodo Timing ”.

Notice:
If the execution time of these scheduled procedures overlaps with the DND time, the product will first perform odour and cleaning and then return to DND mode.

FAULT SELF-CHECK METHOD

1. Re-power the product, click“ Remove Odor” for than 5 times within 2 minutes, and then the product will enter the testing mode.
2. In testing mode：
3. Click each key to check whether the key works properly. If it works properly, the PCB hardware is good.
4. Press the machine from the top with a force of more than 1kg to see whether the“ Full” indicator flashes. If it does, the gravity sensor is good.
5. If the bin mark keeps lighting up, the motor is good.
6. If the WiFi mark keeps lighting up, the WiFi hardware is good.
7. Cover the the infrared sensor at the barrel mouth, if the“ Auto” mark flashes, the sensor is good.
8. Re-power on the machine after checking.

FAQ

Q: Why is the weight data only about half of that of my cats?

A: Please check whether the cat enters the machine with only two feet inside due to curiosity. Or is the machine placed on a flat ground with four feet connecting to the ground?

Q: Why is the App showing motor failure/why is the fault indicator lighted on the equipment panel/why is the equipment always self-checking?

A: If the self-check takes more than 15 minutes, the fault indicator is on. It may be that the barrel compartment is not properly installed or there is foreign matter stuck in the rotation. Please open the buckle of the barrel compartment, lift the barrel to check, and then put it back according to the tips(on the base) and close the buckle.

Q: Why is the clearing time so long?

A: Lower revs make timid cats less scared; It will prolong the whole clearing time if cats enter in or come close frequently due to curiosity.

Q: Why did the machine rotate back for a while before finishing the whole rotation?

A: To save sand and increase the capacity of the collection bin.

Q: Why the poop can’t be cleaned in the garbage box?

A: The door may be blocked by a cat litter garbage bag, or garbage too large to pass through; Please check whether the garbage entrance can be fully opened and closed smoothly(it is recommended to check every time after installing a new bag). Large garbage can be handled manually to make it smaller first.

Q: What kind of cat litter sand should I use?

A: Mixed sand and tofu sand are preferred; Bentonite sand and mineral sand are okay, which may affect the delay time of the “ Full” prompt due to their weight density and liquidity.

Q: Why is there some sand left in the bin after I used the Replace Litter function?

A: Maybe there is not enough space in the garbage bag, please replace the bag and then Replace Litter again.

Q: Why is the sand leaking out from the mouth of the garbage box when replacing the garbage bag?

A: Please press the Remove Odor for 2 seconds, then the litter bin will rotate 90° counterclockwise to ensure that the mouth of the bag is upward when replacing.

Q: Why is the weight data incorrect?

A: Please press the Clean for 2 seconds, the sand will be smoothed and the weight will be calibrated immediately. Also please check whether the machine is placed on a flat and firm ground. Cats that do not fully enter the bin or stay in the bin for too short may also result in inaccurate weighing. If a cat enters the bin while working, it will also get an inaccurate weight.

Q: Why the machine didn’t stop working while the cat entered?

A: The machine won’t stop when performing sand levelling and weight calibrating. However, the safe structure of the product, together with the rotation Angle of the action(±45°) is no danger for the cat to enter in when working.

PRODUCT LIST

INTRODUCTION OF CONTROL PANEL

CIRCUIT DIAGRAM

PARAMETERS AND SPECIFICATIONS

• Product Name
  Smart Cat Litter Box

• Product Model
  MSP-01

• Whole Machine Size
  480(W)×520(D)×505(H)mm

• Rated Voltage
  DC12V

• Rated Power
  ≤18W

• Suggested Pet Type
  Cat

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>