SHURE S53P Low-Profile Long Distance Microphone Stands Instruction Manual
- June 3, 2024
- Shure
Table of Contents
DATA SHEET
MODEL S53P AND
MODEL S55P
S53P Low-Profile Long Distance Microphone Stands
NEW.
For better sound quality in “distance pick-UlP4′, ‘/ sound reinforce’ Vent and
recording
Models S53P and S55P j
Low-Profile, “Long Distance” Microphone Stands
When the microphone is on a conventional stand (left), direct waves reach the microphone before floor-reflected waves, which travel a longer distance. Depending upon the distances involved, phase cancellation is more or less severe. Typically, the resultant response curve (right) shows extensive “holes” or response losses at various frequencies, and an unnatural “hollow” sound results.
When the microphone is lowered to just above the floor (left), both floor reflected and direct waves reach the microphone virtually simulta}:leously- without phase cancellation-and the resultant sound, as shown in the response curve (right), is full and smooth-without cancellation holes.
IMPROVE SOUND QUALITY
Extensive research by Shure on the effects of phase cancellation in distant microphone pick-up techniques has produced the first microphone stands specifically designed to optimize the location of microphones to eliminate the typical “hollow” sound associated with distant pick-up. The S53P and S55P stands hold the microphone suspended only a fraction of an inch above the floor, so floor-reflected sound waves reach the microphone at the same time as direct waves, ilnd philse cancellation is minimized or eliminated. Sound quality is improved, the hollow sound is eliminated, and, depending on conditions, up to 6 db of additional gain can be obtained before feedback.
.. . IN THESE APPLICATIONS
The S53P and S55P stands are ideal for any application in which the distance
from source to microphone is greater than the height of the source from the
floor, or when a simply blended, “one-source” input is desired, and a
distantly positioned, single microphone is used … such as in choral,
orchestral and ensemble musical events, and dramatic or musical stage
presentations.
EXCELLENT NOISE ISOLATION
The S53P and S55P stands provide very effective mechanical shock isolation, so
floor vibration noises and the noise transmitted by conventional microphone
stands are sharply reduced. Both models are lightweight and collapsible, and
their low-profile design allows them to be used unobtrusively right on stage.
Model S53P Microphone Stand. For Shure SM53 Professional Mic rophones on Iy.
Model S55P Microphone Stand. For Shure Model 545, 548, and SM57 Microphones.
“DISTANT PICKUP” MICROPHONE ISOLATION STAND
The Shure Models S53P and S55P are designed specifically for “distant pickup”
microphone situations, where the distance from source to microphone is greater
than the height of the source from the floor. When a conventional microphone
stand is used as in Fig. 1 a, reflections from the floor will arrive out of
phase at the microphone, and cancel out certain groups of tones. If the
microphone is placed on the floor, as in 1 b, these cancellations cannot
occur, and the tonal balance is similar to a close microphone technique.
To be effective, this stand must support the micro phone as close to the
floor as possible without touch ing (approximately V8 inch). It must also
provide excellent shock isolation, so that floor vibrations are not introduced
into the microphone. The S53P and S55P fulfill these requirements.
The Shure Model S53P is designed especially for the Model SM53 Unidirectional
Microphone. The Shure Model S55P is designed for use with the Models 545, 548,
565, SM57, and SM58. (NOTE: The Model S55P is not recommended for microphones
with switches mounted in the handle).
The S53P and S55P Isolation Mounts are of rugged black plastic, rubber, and
stainless steel construction which will withstand the high temperatures of
stage and television lights. The legs of the S53P and S55P are spread apart to
form a tripod microphone stand and may be neatly folded together, making the
entire stand a size which can easily be carried in a brief case.
INSTALLATION
- Evenly spread the stainless steel legs of S53P or S55P so as to form a tripod microphone stand.
- Slip cable end of microphone into isolation mount, using a twisting motion on the micro phone for ease of installation.
- Insert the microphone into the isolation mount to a point where microphone is held firmly enough to prevent its falling out. Attach cable to microphone connector.
- Adjust swivel so that grille of microphone is approximately Va” off floor; aim stand to direc tion of source.
Guarantee: This Shure product is guaranteed in normal use to be free from
electrical and mechanical defects for a period of one year from the date of
purchase. Please retain proof of purchase date. This guarantee includes all
parts and labor.
Shipping Instructions: Carefully repack the ul)it and return it prepaid
to the factory. If outside the United States, return the unit to your dealer
or Authorized Shure Service Center for repair. The unit will be returned to
you prepaid.
222 HARTREY AVE” EVANSTON, IL. 60204 U.S.A.
MICROPHONES AND ELECTRONIC COMPONENTS
AREA CODE 312/328-9000 · CABLE: SHUREMICRO
Copyright 1970, Shure Brothers Incorporated 27A827 (LC)
Printed in U.S.A.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>