techno H35 Smart Door Lock User Manual
- June 3, 2024
- TECHNO
Table of Contents
techno H35 Smart Door Lock
Special Attention:
- Mechanical keys please keep outdoor, just in case keys lock in doors.
- Please replace for the battery when low wattage alarm.
- Reading this manual carefully before installation, and keep it for future reference.
Introduction
Lock structure
Packing List
Check the following drawing to check whether the package contains all the parts
NO | Name ‘ ‘ | Qty | NO. | Name | Qty |
---|---|---|---|---|---|
1 | Front Panel | 1 | 11 | Mortise Screws:10*5 (For Aluminum | |
Door) | 4 | ||||
2 | Back Panel | 1 | 12 | Mortise Screws:25*4mm (For Wooden | |
Door) | 4 | ||||
3 | Mortise: latch | 1 | 13 | 60mm/80mm Square shaft | 2 |
4 | Card | 3 | 14 | M5*25mm Screw for Door Thickness 35-39mm |
2
5| Mechanical Key| 2| 15| M530mm Screw for Door Thickness
40-SOmm| 2
6| Waterproof Rubber Plate| 2| 16| M540mm Screw for Door
Thickness 50-65mm| 2
7| Screw Stubs:M535mm| 2| 17| MSS Omm Screw for Door
Thickness 40-SOmm| 2
8| Screw Stub s:M530mm| 2| 18| M560mm Screw for Door
Thickness 50-65mm| 2
9| Strike & Strike Box| 1+1| 19| UCli p| 1
10| Sliding Screws :1 6*5m m| 2| 20| User Manual| 1
Specifications
Suitable for Models | H35 | Doors Applicable | Aluminum door Wooden door |
---|---|---|---|
Mate r i als | Aluminum alloy | Working Voltage | 6V/ 4x AA |
Batteries
Lock W eigh t| 3KG| Door Thickness
to Fit| 35-65mm
Unlocking
Way
| Bluetooth Fingerprint(option} Password Card Mechanical key Gateway(option}| Data Capacity| Fingerprint, 200 Password, 150
Card, 200
Color| Silver Black| Working Temperature| l O’C-SS’C
L ow Wattage Alarm| Less than 4.BV| Working Humidity| 0-95%
System Initialization
Open the cover plate of the front panel ,long press the “Reset” button on the back panel for 5s, press “000#”,and the initialization is complete
Electronic Locking Button
When you pull the button to “red” status, the lock was on “Locked” status. And it can be opened from outside, only by Master Admin . other unlock ways, when you try to unlock, it will voice out ” the lock was locked”. To disable this function, you need pull the button to “green” status, to release the “Locked” status.
installation
Turn the handle
Notice: Adjust the handle according to the direction you open the door.
For Front Panel
-
Loose Screws
-
Left Open the Handle Toward the Left; Right Open the Handle Toward the Right.
-
Reinstall the Screw After Adjusting the Direction
For Back Panel
-
Loose Screws
-
The direction of the rear panel handle is opposite to the front panel handle
-
Reinstall the Screw After Adjusting the Direction
Installation Diagram(For 5572)
-
Step 1 Install Mortise
-
Step 2 Install Sliding Screw Casing
-
Step 3 Install Back Panel and link wire
-
Step 4 Install fixing screws
-
Step S installation complete
0peration
Registration
The software (iOS version) can be downloaded from the app store, and the Android ( version can be downloaded from the application store of Google play, Yingyongbao, Baidu, Ali, 360, Huawei, and Xiaomi.
Connect lock to the phone
- please scan the QR code to download the app
- You can also search for TT Lock in the APP store(Google Play)to download
- Register a new account (phone number or email) or login with an existing account.
- Touch the lock screen to light, click”+ Add Lock”
- The lock nearby will appear on the phone screen, Click”+”
- Re-name the lock
- The lock added successfully
TT lock users can register the account by mobile phone and Email which currently support 200 countries and regions on the world. The verification code will be sent to user’s mobile phone or email, and the registration will be successful after the verification.
Add locks
TT Lock supports multiple types of lock devices. The lock needs to be added by the app after entering the add mode. Generally, a lock that has not been added, as long as the lock keyboard is touched, it will enter the add mode. The default password is 123456 if not added by the phone
User Management
Bluetooth management
Make sure there is no problem with Bluetooth communication. After connecting
the phone to the door lock as above, Click ” i “to unlock.(the phone is within
Smelters from the door lock)
Setting Passcode
Passcodes are also a way to unlock. After entering the passcode on the locked
keyboard, press the unlock button in the lower right corner to unlock.
Passcodes are divided into permanent, time-limited, single, clear, cycle, and
custom.(You can share the Passcode to other user via WeChat, SMS, Email,
Messenger, WhatsApp)
Send e-Key
Click on the” “as shown in figure, you can send the Key to other users of TT
lock to authorize the unlock(the receiver must be download the APP and set up
an account)- Select e-key format (Timed, permanent, One-time, Recurring) –
Enter recipient’s account of TT lock, set the name and effective time of the
Key, Can choose to allow remote unlocking or disallowing, authorized
administrator or not authorized, as shown in figure -Send-The recipient’s
account has Bluetooth unlock permission
Add card
Supports opening doors through various IC cards. Before an IC card is used to
open the door, it needs to be added first. The adding process needs to be
performed by the app beside the lock. The validity period of the IC can be
set, it can be per anent, or it can be limited in time.
Add fingerprint
The premise that a fingerprint can be used to open a door is that it needs to
be added first. The adding process needs to be performed by the APP beside the
lock. The fingerprint expiration data can be set, it can be permanent, or it
can be limited. After setting ,y9u can modify its validity period .
e-Key management
Click ” ” The manager can delete e key, reset e key, send and adjust the
e-key, meanwhile he can search the lock record.
Passcode management
Click All generated passwords can be viewed and managed in the password management module. This includes a password change, password deletion, password reset, and password unlock record.
Unlock records
Click” © “you can query your unlock record as shown in figure
Gateway management(Optional)
The TT lock is directly connected via Bluetooth, that is why it is not attacked by the network. The gateway is a bridge between smart locks and home WIFI networks. Through the gateway, the user can remotely view and calibrate the lock clock, read the unlock record. Meanwhile, it can remotely delete and modify the password.
Add Gateway
Light Status
Pair the Gateway with APP
-
Activate the APP
-
Press·
-
Select Gateway
-
Select
-
Plug in the gateway and power it on. while the bight flashes alternately in reel and blue
-
Press • + • s, gn
-
Add Gateway
-
Select the networ1< and fill ” in the password
-
Add complete
Notice: If tames out, please power off and try ,t again.
Manual
After a short period of time, you can see which locks are in their coverage in
the app. Once the lock is bound to the gateway, the lock can be managed
through the gateway
FAQ
- Customer Name:
- Customer Calls
- Purchase Date
- Product Name
- Product Model
Note:
- Please keep this card so that you can use it when you need warranty service.
- We provide you with a one-year warranty from the date of purchase.
- This warranty service is valid for customers in any country in the world.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>