Smartrak OBD II-FT200 Self-Install Telematics Tracker User Guide
- June 3, 2024
- Smartrak
Table of Contents
Smartrak OBD II-FT200 Self-Install Telematics Tracker
Self-Install Telematics Tracker
Safety Warnings
*Read this complete guide before installing the device
This device contains a Lithium Ion battery. If these guidelines are not followed, the battery may experience a shortened life span or may present a risk of damage to the device, fire and/or bodily injury.
- Do not penetrate the battery or device with a nail etc., nor make a hole in the battery.
- Do not throw the battery or the device into fire, nor heat the battery above the specified operating temperature range of 158°F / 70°C.
- Do not place the device in direct sunlight in an enclosed space such on the dashboard of an unattended vehicle.
- Do not disassemble nor modify the battery.
- Do not put the battery into a microwave oven or high-pressure container.
- Contact your local waste disposal department to dispose of the device/battery in accordance with applicable local laws and regulations.
About Your New Device
The device you are about to install connects to your vehicle’s onboard diagnostics port (OBD-II) to gather applicable diagnostics data. It contains a GPS receiver for location and an LTE cellular modem to communicate.
LEDs
The LEDs indicate device activity at startup and its live functional status (if enabled).
| GPS | Data | Power | |
|---|---|---|---|
| Off | GPS off | Modem off | Device off or sleeping |
| On | GPS has location fix | Connect to cellular network | System is awake |
| Rapid Flash | Receiving GPS location | Transferring cellular data |
Telematics transferring data
Medium Flash| Searching for satellites| Searchi ng for cellular
network| Device unlocked (3 sets of 4)
Error Codes
| LED Color | Flash Count | Error |
|---|---|---|
| Data | 1 | SIM error |
| 2 | No network | |
| 3 | Unable to register with network | |
| 5 | Service act ivation error | |
| 6 | Service sync failure | |
| GPS | 3 | GPS signal too weak |
| Power | 4 | Batt ery too low to transm it |
| 5 | Er ro r reading telemat ics data | |
| 10 | Other system error |
Troubleshooting
| Symptom | Action |
|---|---|
| LED slow flashes a repeated pattern | The device is in error state; check the |
error codes above for corresponding actions
Record Device Information
Record the following information for activation and for your records:
- Device Product Name (see image of label below)
- Device Model Name (see image of label below)
- Device SN/IMEI (see image of label below)
- Device ICC ID (if available)
Installation
IMPORTANT! Please shut off the vehicle, remove the device and notify us if you encounter any of the following:
-
Your vehicle’s OBD-II port location is such that after installation, the device will interfere with entering or exiting the vehicle.
-
The device cannot be securely inserted and may become loose with vibrations during driving.
-
You notice any warnings on the instrument panel after installing the device.
Park your vehicle outside (as opposed to in a garage). -
Locate your vehicle’s OBD-II or engine diagnostics port, generally in the driver’s area at or below knee level.
-
Note that it may have a cover which you would need to open or remove. Store the cover so you may replace it later.
-
Align the device with the port and push in place securely.
FCC Warning statements
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:(l) This device may not cause interference;
and(2)This device must accept any interference, including interference that
may cause undesired operation of the device.
Suppliers Name: flex Industrial Ltd
Suppliers Address (USA): 6201 America Center Drive
San Jose CA 95002 USA
Suppliers phone number· 408 576 7000
Caution: The user is cautioned that changes or modifications not expressly approved bythepartyresponsibleforcompliancecould void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If his equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to cotTect the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connecttheequipmentintoanoutletonacircuitdifferentfrom that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. It maintains at least a 20cm separation between the
EUT and the user’s body and must not transmit simultaneously with any other
antenna or transmitter.
ISED Warning statements
This device complies with Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions:(l) This device may not cause interference;
and (2)This device must accept any interference, including interference that
may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
CE Warning statements
Hereby, Flex Industrial, Ltd. declares that the radio equipment type FT200 is
in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
Suppliers Name: Flex Industrial. Ltd.
Suppliers Address (USA): Level 3, Alexander House 35 Cybercity, Ebene,
Mauritius
Suppliers phone number: 408 576 7000
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Warning statements
This device complies with Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions: (l) This device may not cause interference;
and (2) This device must accept any interference, including interference that
may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and any part of your body.
This Class B digital apparatus complies with Canadian ICES-003.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>