BACA SYSTEMS M Series Robo SawJet Owner’s Manual

Owner’s Manual

M Series Robo SawJet

RSJM Dual Pocket Left Utilities
System Dimension:
31-6 ¼” x 18′-6 ½”
Overall Footprint (incl. utilities & clearance):
39′-4″ x 21′-2”
Utility Requirements
Power:
1 Circuit 480V 3Phase 80A (65 FLA) (Robot)
1 Circuit 480V 3Phase 100A (63 FLA) (Pump)
Air:
5 CFM @ 85-100 PSI Range (Robot)
3 CFM @ 60-100 PSI Range (Garnet Hopper)
Water:
1 Source Clean
1 Port 4gom (Waterjet)
1 Port 3-Sgom <65°F (Pump Cooling Water)
1 Source Gray Sgom (Saw Water)

RSJM Dual Pocket Right Utilities

System Dimension:
31-6 ¼” x 18′-6 ½”
Overall Footprint (incl. utilities & clearance):
39′-4″ x 21′-2”
Utility Requirements
Power:
1 Circuit 480V 3Phase 80A (65 FLA) (Robot)
1 Circuit 480V 3Phase 100A (63 FLA) (Pump)
Air:
5 CFM @ 85-100 PSI Range (Robot)
3 CFM @ 60-100 PSI Range (Garnet Hopper)
Water:
1 Source Clean
1 Port 4gopm (Waterjet)
1 Port 3-5gom <65°F (Pump Cooling Water)
1 Source Gray Sgom (Saw Water)

RSJM Dual Pocket Back Utilities
System Dimension:
31′-6 ¼” x 18′-6 ½”
Overall Footprint (incl. utilities & clearance):
32-10 ¼” x 27′-9″
Utility Requirements
Power:
1 Circuit 480V 3Phase 80A (65 FLA) (Robot)
1 Circuit 480V 3Phase 100A (63 FLA) (Pump)
Air:
5 CFM @ 85-100 PSI Range (Robot)
3 CFM @ 60-100 PSI Range (Garnet Hopper)
Water:
1 Source Clean
1 Port 4gom (Waterjet)
1 Port 3-S5gom <65°F (Pump Cooling Water)
1 Source Gray S5gpm (Saw Water)

RSJM Dual End Load Back Utilities
System Dimension:
33-9 ¾” x 18°6 ½”
Overall Footprint (incl. utilities & clearance):
33′-9 ¾ x 27″-9″
Utility Requirements
Power:
1 Circuit 480V 3Phase 80A [65 FLA] (Robot)
1 Circuit 480V 3Phase 100A (63 FLA) (Pump)
Air:
5 CFM @ 85-100 PSI Range (Robot)
3 CFM @: 60-100 PSI Range (Garnet Hopper)
Water:
1 Source Clean
1 Port 4gpm (Waterjet)
1 Port 3-Sgpm <65°F [Pump Cooling Water)
1 Source Gray 5gpm (Saw Water)

RSJM Dual Table Layout Elevation View

Required overhead clearance with cameras: 12′-2″
Required overhead clearance without cameras: 11′-7″

RSJM UTILITY REQUIREMENTS

Reference pages in the Robo SawJet M-Series Pre-Install Document

ROBOT

1. Airtine [pg. 13]

2. Foundation [pg. 14] Saw Water/Grey Water [pg. 12] – Place saw water connection minimum 36″ away from any power supply
   H20 JET PUMP

3. Power [pg. 8] – 1 Circuit 480V 3Phase 100A 60Hz

4. H2O Pump Clean Water [pg. 9] KUKA ELECTRICAL CABINET

5. Robot Power [pg. 8] – 1 Circuit 480V 3Phase 80A 60Hz

6. Ethernet [pg. 3] (Internet Connection – Hard Wired)
   GARNET HOPPER

7. Aittine [pg. 13]

See Pre- Install Document For Additional Information
PROPRIETARY AND CONFIDENTIAL.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BACA SYSTEMS.
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF BACA SYSTEMS IS PROHIBITED.

RSJM Dual Table Layout – Utility Hook Up Points
Job No: —–| REV: L-1.01
SIZE: B| SCALE 1:50| 11/8/2023| SHEET 6 OF 6

FINAL PLACEMENT DETERMINED
DURING INSTALLATION. DO NOT SCALE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>