OEM TOOLS 24484 20V Max Lithium Ion Brushless Drill User Manual
- June 1, 2024
- OEM-TOOLS
Table of Contents
- OEM TOOLS 24484 20V Max Lithium Ion Brushless Drill
- UNPACKING
- WARNING
- Explanation of Safety Signal Words
- POWER TOOL SAFETY
- BATTERY TOOL USE AND CARE
- PRODUCT SPECIFICATIONS
- INSTRUCTIONS
- DRILLING
- DRIVING SCREWS
- POWER SOURCE CONNECTION POWER REQUIREMENTS
- PARTS DIAGRAM
- PARTS LIST
- Specifications:
- CONTACT US
- FAQ (Frequently Asked Questions)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OEM TOOLS 24484 20V Max Lithium Ion Brushless Drill
USER MANUAL
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
customerservice@oem-tools.com
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
UNPACKING
After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. If any damage is observed, a shipping damage claim must be filed with the carrier. DO NOT use the OEMTOOLS® 24484 20V Max* Lithium-Ion 1/2″ Brushless Drill if broken, bent, cracked or damaged parts (including labels) are noted. Any Drill that appears damaged in any way, operates abnormally or is missing parts should be removed from service immediately. If you suspect that the Drill was subjected to shock load (a load that was dropped suddenly, unexpectedly, etc.) immediately discontinue use until it has been checked by a factory authorized service center.
*Voltage is measured without workload. Maximum initial battery voltage after charging. Nominal voltage is 18 Volts.
WARNING
The following safety information is provided as a guideline to help you operate your Drill under the safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these instructions for the continued safe use of your Drill . Failure to follow instructions listed below may result in serious injury. In addition, make sure that anyone who uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
NOTES: Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS® Product!
For future reference, please register your new tool at www.oem-tools.com and
complete the owner’s record below:
Model: ____ Purchase Date:
Save the receipt, warranty and these instructions. It is important that you
read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS®
cannot be responsible for issues arising from modification. We strongly
recommend that this product is not modified and/or used for any application
other than that for which it was designed. If you have any questions relative
to a particular application,
DO NOT use the product until you have first contacted customer service to determine if it can or should be performed on the product.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
POWER TOOL SAFETY
WARNING
Read and understand all safety warnings and instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
WORK AREA SAFETY
1. Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of a ground fault circuit
interrupter (GFCI) reduces the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust related hazards.
POWER TOOL SAFETY
1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
3. Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
8. Hold power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring or its own cord.
Fasteners contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
9. Hold power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring or its own cord.
Fasteners contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
BATTERY TOOL USE AND CARE
1. Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
WARNING
1. Know your cordless, brushless Drill. Do not plug in the charger or install
the battery in the tool until you have read and understand this Instruction
Manual. Learn the tool’s applications and limitations, as well as the specific
potential hazards related to this tool. Following this rule will reduce the
risk of electric shock, fire, or serious injury.
2. Always wear eye protection. Any power tool can throw foreign objects into
your eyes and cause permanent eye damage. ALWAYS wear safety goggles (not
glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have
only impact resistant lenses. They ARE NOT safety glasses.
3. Glasses or goggles not in compliance with ANSI Z87.1 could cause serious
injury when they break.
4. Always use a safety shield, hearing protection and dust mask when
operating the Drill.
5. To avoid fire or toxic reaction, never use gasoline, naphtha and acetone,
lacquer thinner or similar highly volatile solvents to clean the tool.
6. Use only accessories that are designed for use with this tool. Follow the
instructions that accompany accessories. The use of improper accessories may
result in injury to the operator or damage to the tool.
7. If any part is missing or damaged, do not plug the tool into the power
source or install any accessory until the missing or damaged part is replaced.
Do not drill material too small to be securely held.
8. Always keep hands out of the path of the drill bit. Avoid awkward hand
positions where a sudden slip could cause your hand to move into the path of
the drill bit.
9. Secure the workpiece. Use clamps or a vice to hold the workpiece. It is
safer than using your hand and it frees both hands to operate the tool.
10. Make sure there are no nails or foreign objects in the part of the
workpiece to be drilled.
11. To avoid injury from accidental starting, always remove the battery from
the tool before installing or removing a drill bit.
12. Do not install or use any drill bit that exceeds 7″ (17.5 cm) in length
or extends more than 6″(15 cm) beyond the chuck jaws. They can bend or break
suddenly.
13. Before starting the operation, jog the drill switch to make sure the
drill bit does not wobble or vibrate.
14. Do not use fly cutters or multiple-part hole cutters, because they can
come apart or become unbalanced during use.
15. Make sure the spindle has come to a complete stop before touching the
chuck or attempting to change the drill bit.
16. Always make sure the chuck is tight and the drill bit firmly tightened in
the chuck before starting drill.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
WARNING
Use only attachments recommended or sold by manufacturer.
1. Do not disassemble the Drill. Take it to a qualified professional when
service or repair is required. Incorrect reassembly may result in electric
shock or fire.
2. Wear approved safety eye/face shield, ear defenders and hand protection.
DISPOSAL
At the end of the useful life of the OEMTOOLS® 20V Brushless Drill, dispose of the components according to all state, federal and local regulations.
BATTERY DISPOSAL
Exposure to high temperatures can cause the batteries to explode; do not
dispose of in a fire. Some countries have regulations concerning battery
disposal. Follow
all applicable regulations. Return used batteries to a collection location for
recycling. Call 800-822-8837 or visit
www.call2recycle.org to find a collection location.
PURPOSE
The OEMTOOLS® 20V Max* Lithium-Ion 1/2″ Brushless Drill is used for drilling holes, driving screws, loosening or tightening various materials together with fasteners and other applications.
PRODUCT SPECIFICATIONS
- Keyless Jacob’s Chuck: 1/2″
- Variable Speed: 0-600 RPM and 0-2000 RPM
- Max. Torque: 310 In/Lb.
- Clutch: 21+1 Torque Setting
- Electric Brake: Yes
- Battery: 2.5Ah Li-ion
- Charge Time: 1 Hr.
- Weight: 7.63 Lb.
INSTRUCTIONS
Always wear safety goggles and gloves.
DRILLING
1. If drilling in a small workpiece, make sure it is securely held in a vise
or clamped to a secure platform such as a bench or table.
2. Install the correct drill bit in the chuck. Rotate the chuck body to
loosen or tighten the drill bit in the chuck. Never use the drill’s power to
rotate the chuck body.
3. Select the rotation direction to clockwise using the button located above
the trigger switch.
4. Select the correct transmission speed. Use the slower speed for drilling
large holes.
5. Set the torque adjusting collar to the drilling position (drill icon on
tool).
6. Slide the fully charged battery pack onto the base of the handle.
7. Mark the drilling point with a center punch when drilling in metal to
prevent the drill bit from slipping off center as you begin drilling.
8. Place the drill bit at the location of the hole to be drilled and squeeze
the trigger. The harder you squeeze, the faster the drill turns.
DRIVING SCREWS
1. Install the correct screwdriver bit in the chuck. Use the largest bit size
that will properly fit the screw. Make sure the flat sides of the bit are
gripped by the chuck.
2. Set the transmission speed to low speed.
3. Set the rotation directions to clockwise.
4. Set the torque collar to #10.
5. Place the screwdriver bit into the screw and hold the bit firmly into the
screw to prevent slippage and drive a test screw.
6. After driving a test screw, adjust the torque setting up or down so the
screw is driven to the desired depth without being over driven.
7. Release the trigger immediately when the torque clutch begins to “rattle”.
8. Driven screws can be removed by reversing the direction of the rotation.
WARNING
Always charge the battery pack indoors in a well-ventilated area. The charger must never be subjected to wet conditions.
ELECTRICAL WARNING
POWER SOURCE CONNECTION POWER REQUIREMENTS
This product is designed to operate on a properly grounded 120 volt, 60Hz, single-phase alternating current (AC) power source fused with a time delayed fuse or circuit breaker. It is recommended that a qualified electrician verify the ACTUAL VOLTAGE at the receptacle into which the product will be plugged and confirm that the receptacle is properly fused and grounded.
DO NOT OPERATE THIS PRODUCT if the ACTUAL power source voltage is less than 105 Volts AC or greater than 132 Volts AC. Contact a qualified electrician if this problem exists. Improper performance and/or damage to the product will result if operated on inadequate or excessive power.
DO NOT abuse cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
CHARGING THE BATTERY PACK:
1. Place the charger in a dry location near a 120V/60Hz electrical outlet.
2. Plug the charger into the electrical outlet.
3. The green LED light will turn on.
4. Turn the battery pack upside down and slide it onto the charger.
5. The green LED light will turn off and the red LED light will begin to
flash indicating the battery pack is charging.
6. The red LED light will turn off and the green LED light will turn on when
fully charged.
7. Once the battery pack is fully charged, remove the charger plug from the
power source and remove the battery pack from the charger.
NOTES: Do not charge batteries when the work area or the battery temperature is at or below 32°F (0°C) or above 113°F (45°C).
Green Light| Red Light| Battery on the Charger| Charging
Status
---|---|---|---
ON| OFF| NO| Charger connected to power supply
OFF| FLASHING| YES| Battery charging
ON| OFF| YES| Battery fully charged
OFF| ON| YES| Battery defective or bad contact
ON| ON| YES| Battery too hot or too cold to be charged
Intertek
3042597
JD6286
This symbol designates that this tool is listed with U.S. requirements by ETL Testing Laboratories, Inc. Conforms to UL Std. 60745-1 and 60745-2-2.
PARTS DIAGRAM
NOTES: Not all components of the Drill are replacement items, but are illustrated as a convenient reference for location and position in the assembly sequence.
PARTS LIST
Figure | Description | Qty. |
---|---|---|
A | Chuck Screw | 1 |
B | Chuck | 1 |
C | Screw | 3 |
D | Plate | 1 |
E | Positioning Spring | 1 |
F | Torque Setting Ring | 1 |
G | Inner Threaded Ring | 1 |
H | Spring | 1 |
I | Washer | 2 |
J | Needle Roller | 6 |
K | Needle Roller | 6 |
L | Shaft | 1 |
M | Bearing | 1 |
N | Bushing | 1 |
O | Gear Box | 1 |
P | Washer | 1 |
Q | Circlip for Shaft | 1 |
R | Washer | 1 |
S | Driving Block | 1 |
T | Shaft Lock Ring | 1 |
U | Needle Roller | 6 |
V | Planetary Carrier | 1 |
W | Gear Ring | 1 |
X | Planetary Gear | 4 |
Y | Washer | 1 |
Z | High/Low Gear Box | 1 |
AA | Screw | 4 |
BB | Moveable Ring Gear | 1 |
CC | Planetary Carrier | 1 |
DD | Planetary Gear | 4 |
Figure | Description | Qty. |
---|---|---|
EE | Planetary Carrier | 1 |
FF | Fixed Ring Gear | 4 |
GG | Planetary Gear | 4 |
HH | Washer | 1 |
II | 2-Speed Lever | 1 |
JJ | Motor Gear | 1 |
KK | Brushless Motor | 1 |
LL | Optical Rod | 1 |
MM | Screw | 4 |
NN | Cover Plate | 1 |
OO | Speed Selector Button | 1 |
PP | Lever | 1 |
Rear Housing | 1 | |
RR | Left Housing | 1 |
SS | Forward/Reverse Lever | 1 |
TT | Trigger Assembly | 1 |
UU | Screw | 1 |
VV | Belt Hook | 1 |
WW | Lock Washer | 2 |
XX | Hex Nut | 2 |
YY | Contact Plate | 1 |
ZZ | Right Housing | 1 |
AAA | Screw | 7 |
BBB | Battery | 1 |
Don’t forget to register your new OEMTOOLS® product at www.oem- tools.com.
Specifications:
- Model Number: 24484
- Product Type: 20V MAX* LITHIUM-ION 1/2 BRUSHLESS DRILL
- Voltage: 20V MAX* (Nominal voltage is 18 Volts)
WE STAND BEHIND OUR TOOLS. OEMTOOLS® 1 YEAR WARRANTY
If within 1 year from the date of purchase of this OEMTOOLS product, you find any defect in material or workmanship, through normal usage, return it to the place of purchase or to OEMTOOLS® for repair or replacement at our discretion. In order to obtain this service, send your tool and proof of purchase (transportation pre-paid) to:
OEMTOOLS® Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation;
please insure your package. If our inspection verifies the defect, we will
repair or replace the product, or we may elect to refund the purchase price if
we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or
that the defect resulted from causes not within the scope of our warranty,
then you must bear the cost of returning the product.
OEMTOOLS® does not provide warranty for products labeled other than OEM® or
OEMTOOLS®. OEMTOOLS® will not provide any warranty for products subjected to
abnormal use. Abnormal use includes (but is not limited to) abuse, accident,
alteration, neglect, and unauthorized or unreasonable use or repairs. This
warranty does not cover bits, blades, files, batteries, or calibration. We
recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS® reserves the right to make any
changes in construction or design at any time without any obligation in
incorporating such changes to tools or equipment previously sold.
OEMTOOLS® makes every effort to ensure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship. This warranty does not
apply to damage due directly or indirectly to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may
not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Please contact us at customerservice@oem-tools.com or call us at 901-370-1101 for additional information or questions.
Thank you for your purchase.
CONTACT US
3580 E. Raines Road, Suite 3, Memphis,
TN 38118
Tel: 1-866-458-2472
www.oem-tools.com
FAQ (Frequently Asked Questions)
Q: What should I do if the drill stops working suddenly?
A: If the drill stops working suddenly, first check if the battery is charged. If the battery is fully charged, there may be a technical issue with the drill itself. In such cases, contact customer service for assistance.
Q: Can I use this drill for drilling through concrete?
A: This drill is suitable for drilling through various materials, but for concrete drilling, it is recommended to use specific masonry drill bits and follow proper drilling techniques to avoid damaging the drill.
References
- tools.com | Buy Power Tools and Automotive Parts online
- Call2Recycle | Leading the Charge For Battery Recycling
- OEMTOOLS
- P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>