HLIVELOOD B0CP2735JX TV Table LED TV Stand for 65 Instruction Manual

June 2, 2024
Hlivelood

HLIVELOOD B0CP2735JX TV Table LED TV Stand for 65

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-
for-65-PRODUCT

Specifications

  • Model: TV Table
  • Parts Included: Refer to Parts List
  • Tools Required: A, B, C, D, E, F, G, H, I, J, K, L, M

Important Information
Please read the entire manual before starting to assemble and/or use this product. Follow the manual thoroughly and keep it for further reference.

Avoid Scratches
In order to avoid scratching the furniture, assemble it on a soft layer, such as a rug.

Improve Efficiency
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Topple Warning
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment. If not included with this product, please purchase the appropriate wall attachment that fits your wall. If unsure, seek professional advice.

Parts List
Refer to the parts list provided in the manual for a detailed list of components included.

Tool Preparation
Prepare the following tools as listed in the manual before installation. Carefully confirm whether each screw corresponds to the manual.

IMPORTANT INFORMATION!
please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES!
In order to avoid scratching this furnuture should be assembled on a soft layer-could be a rug.

IMPROVE EFFICIENCY !
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(5\)

ANTI-TOPPLE WARNING!
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fit your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months – in order to assure stability through-out the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Board Identification

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(6\)

PARTS LIST

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(7\) HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-
Stand-for-65- \(8\)

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(9\) HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-
Stand-for-65- \(10\)

  • Screw the cam bolt (B) into the panel (2) & (14)&(15)&(18) .

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(11\) HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-
Stand-for-65- \(12\)

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(13\)

  • Attach panel (14)&(15) to(18) and lock with cam(A).
  • Attach panel (12)&(17) to(14) &(15)&(18)and lock with cam(A) and wood dowels(C). HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(14\)

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(15\)

  • Attach panel (2) to(12)&(14)& (15)&(17)&(18)and lock with cam(A) and wood dowels(C).
  • Attach panel (16) to(2) and lock with cam(A). HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(16\) HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(17\)
  • Stick the pads(K) on the foot.
  • Screw the adjustable foot (J) into the panel (16). HLIVELOOD-HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(18\)B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(18\) HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(19\)
  • Attach panel (3)&(4)&(5)&(6) to (2) and lock with cam(A) and wood dowels(C).
  • Stick the hole (L) to the keyhole. HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(20\)
  • Insert panel (13) into the grooves. HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(21\)
  • Screw the cam bolt (B) into the panel (1).
  • Stick LED band to of the panel (1) .
  • Fasten the LED band with buckles . HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(22\)
  • Attach panel (1) to(3)&(4)& (5)&(6)and lock with cam(A) and wood dowels(C).
  • Stick the hole (L) to the keyhole. HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(23\)
  • Insert layer pin (H) into board (3)&(4)&(5)&(6) .
  • place shelf panel (7)&(8)&(9) in as shown. HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(24\)
  • Install the feet (E) on (10) with screws (G).
  • Install the feet (F) on (11) with screws (G). HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(25\)
  • Install the panel (10)&(11) on (3)&(4)&(5) with screws (G).

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(26\)

  • Install handle (D) to panel (10) & (11) with bolts. HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(27\)
  • Insert buckle (1) into back slots and fix with screw (G) as shown.

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(28\)

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(29\)

LED lamp with effective remote control distance of 5 meters

HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65-
\(27\)

  1. Take out the remote control gasket HLIVELOOD-B0CP2735JX-TV-Table-LED-TV-Stand-for-65- \(27\)
  2. .Align romote controller to the RGB Control box to adjust the color mode

RF Wireless Remote

R G B LED Controller

Instructions

  • 22 Dynamic Modes Card Type RF Remote
  • 20 Dynamic Color UltraSlim Design
  • Very Smooth Effects Dynamic Demo Mode
  • Speed Adjustable Easy Remote Pairing
  • Brightness Adjustable Direct Color Select
  1. Turn On/Standby
    Press this key to turn on unit or switch to standby mode.
    At power on,unit will automaticly turn on and restore to previous status.

  2. 9. Dynamic Mode Adjust
    Switch to dynamic mode from static color,or switch between dynamic modes.

  3. 10.Dynamic Speed Adjust
    Adjust dynamic playing speed.Press SPEED+ to increase speed and press SPEÈD-to decrease.Unit will switch to dynamic model f press this key at static color mode.

  4. 5.Static Color Adjust
    Switch to static colormode from dynamic mode ,or switch between static colors.

  5. Direct Color Select
    Shortcut key to static colors When press the specific colorkey,LED will play the same static color.The direct colors are included in ‘COLOR+’ and ‘COLOR-‘ operations.

The maximum constant current is 2amperesper channel.
Please reduce load if main unit is overheating.

CAUTION! Do not short circuit or overload the LED outputs,this may lead to permanent damage!

Operation

  1. Using Remote Controller
    Please pullout the battery insulate tape before using.The RF wireless remote signal can pass through a barrier,soit’s not necessary to aim at the main unit when operate.
    For proper receiving remote signal,please do not install themain unit in closed metal parts.

  2. Pairing New Remote
    The remote and main unitis 1to1 pairedas default.Further more ,main unit can be paired to 3 remote controllers and each remote controller can be paired to any main unit.Please do following steps to pair new remote controller:

  3. Plug off the power of main unit and plugin after 5 seconds .

  4. Press’SPEED-‘ and ‘SPEED+’key together in 5 seconds after power on. After this operation,the main unit will recognize the new remote controller.

  5. Free Remote Pairing Mode
    In some specific cases, the main unit may need to be pairedto any remote controllers.Please do the following steps for freere mote pairing mode:

Functions

Brightness Adjust

Adjust static color brightness.Press BRIGHT +to increase brightness and press BRIGHT-to decrease.Unit will switch to static color model f press this key at dynamic mode.

Demo mode
Press this key will switch to Demo mode. At demo mode,itplays 17 dynamic modes in loop,each mode repeat 3 times.

Installing

  1. Power Supply
    This unit accepts DC5Vto24Vpower supply.The DC jack’s inner pole (or red cable) is positive and sleeve(or black cable) is negative. Also please make sure the power supply voltage is same as the LED load,

  2. LED Output
    This unit support common anode connection LED products.The mark  indicates the common connection node.

  3. .Plug off the power or main unit and plug in afler 5 seconds.

  4. press ‘ON/OFF’ and ‘MODE + key together in 5 seconds after power on.

After this operation, the main unit will recognize any remote controller. To pair the main unit back to specific remote,please repeat the Pairing New Remote operation.

Switch Output Color Sequence

The control ICR’s default output signal sequence is Common-Green-Red-Blue.lf the LED application is in a different cable sequence, the direct color keys will not match the LED color. In this case, user can adjust the output signal sequence with the following steps:

  1. Plug off the power of main unit and plugin after 5 seconds .
  2. Press’RED’and’BLUE’color key together in 5 seconds after power on.
    With this operation,the output sequence will switch between 6 possible combinations.The sequence will be memorized and it won’tchange before next same operation.

Specification

Dynamic mode 22 modes
Static Color 20 colors
PWM Grade 256 levels
Brightness Grade 5 levels
Speed Grade 10 levels
Demo mode Yes
Direct color Select Yes
Output Color Swichable Yes,6 options
Working Volage DC5~ 24V
OutpuCurent 3x2A constant
Remote frequency 433.92MHz
Remote distance >15mat open area

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals