Warmtoo WT-EF502 24 Inch Electric Fireplace Heater Owner’s Manual

Owner’s Manual Electric Fireplace
Model No. WT-EF502

PLEASE SAVE THIS INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
Thank you for choosing Warmtoo Electric Fireplace. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.

IMPORTANT INSTRUCTIONS

When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater by yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater.
4. Keeo combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
5. Extreme caution is necessary when any heater is used by or near children, or when the heater is left operating and unattended.
6. D0 NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
8. D0 NOT touch the control panel or plug with a wet hand.
9. D0 NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings.Arrange card away from where it will not be tripped over.
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may became blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames.
13. Always plug heaters directly into a wall outlet receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
14. To avoid fire or shock hazard, plug the unit directly into a 120V AC electrical outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is notin use.
17. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons, The use of attachments not recommended or sold by unauthorized dealers may cause hazards.
18. Always use on a dry, level surface. Use on floor only.
19. D0 NOT use outdoors.
20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only.
    SAVE THESE INSTRUCTIONS

SPECIFICATIONS

SAFETY FEATURES

Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal components reach a certain temperature that could cause overheat and possible fire, the heater will automatically shut off.

N THE BOX
REMOTE CONTROL (2 AAA Batteries Not Included)
ELECTRICSTOVE LEG(4pcs) SCREW(12pcs) *INSTRUCTION BOOKLET

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. Tools Required for Assembly (not included): Phillips screwdriver

ASSEMBLY INSTRUCTIONS

Lay stove upside down on a padded surface with the underside accessible. Attach leg to stove by inserting the tab on the top of the leg into the corresponding slot on the bottom of the stove. Insert three screws into predrilled holes and tighten securely. Repeat with remaining three legs

WARNING:
It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.

PRODUCT DIAGRAM

Control Panel

1. Power indication light: After electrifying show red, press the power button to display the red light and flame open.
2. Power button: Powers the display on and off.
3. Flame light: When the flame function is on, the indicator lights up.
4. Flame light button: Adjust the brightness of the flame
5. Timerlight: After the timing function is enabled, the indicator lights up.
6. Timer button: User setting timing boot or shutdown
7. Up button: For setting temperature or time upward
8. D0wn button: For setting temperature or time downward
9. Heater button: Set up the heater mode and turn off the heat.
10. Low range mode lights: Low range mode indicator lights up for low-grade heat.
11. High range mode lights: High range mode indicator lights up for high-grade heat.

Digital display:
Indicate set room temperature or time value according to the timer ar High and Low heating mode display After 5 seconds, the display window automatic blanking, press any key to the window automatically display except for the power button.

Remote Control

PREPARATION

Place the heater ona firm, level surface and plug into a 110-120V~60Hz power outlet. And turn on the power switch in the front of the unit. Only operate heater in upright position with caster wheels attached.
Insert 2*AAA batteries into the remote control before using (Batteries Not Included)

OPERATING YOUR HEATER

Once the Electric fireplace has been properly assembled and connected to a electrical outlet and make sure the main switch is “ON’ (main switch light is shining). it is ready to operate:

1. Start and select working mode

| Turn the heater on by pressing the ON/OFF button on the control panel or by pressing the Power button on the supplied remote control. Once power is off, heating element will stop working at first. Fan will prolong working for 1 min to emit plenty of heat  inside. Then shut OFF automatically
---|---
| Select a heat setting.
Press the HEATER button to toggle between the two heat settings.
| Power for heat-up mode is 1500W; heat-down is 750W, and turn off the heat.

2. Setting room temperature

| Adjust the thermostat by pressing the arrows on the control panel or remote control.3
---|---
59-60-61……95| Set temperature indication varies from 59° F to 95°F. Once you have chosen the desired temperature, the heater will remain on until the room temperature increases to the temperature on the digital display. The heater will cycle on
and off to maintain the desired room temperature.

3. Setting flame

| Adjust the brightness of the flame and turn off
---|---

4. Setting timer-power- off
Caution! ONLY under power-off mode can you set timer-power-off function.

| When starting the unit, press the timer button on the control panel.
---|---
| Adjust the time by pressing the arrows on the control panel or remote control.aa
---|---
| Digital display turns set temperature to time value for the timer. Press the UP or DOWN button more than once, the value will vary from 0 to 12hr (1 hr interval) in circulation.
| The light is on when timer -power-off is set.

5. Setting timer-power-on
Caution! ONLY under power-off mode can you set timer- power-on function.

| Under power-off, press the timer button on the control panel.
---|---
| Adjust the time by pressing the arrows on the control panel or remote control.
| Digital display indicates time value for the timer. Press the UP or DOWN button more than once, the value willyaryfrom 0 to 12hr (1 hr interval) in circulation.
| The light is on when timer -power-on is set.

6. Setting electro lock
Function of electro lock can avoid misoperation from children. Locking can be set in both power-on and power-off modes.

| Press Temp Up and Temp Down buttons once for 3 seconds. Locking is fulfilled when a buzzer rings. When locked, control panel and remote control failed to function.
---|---
| When release is needed, please re-press Temp Up and Temp Down buttons once for 3 seconds. Release is fulfilled when a buzzer rings. Lock indication disappears. Control panel and remote control return to function.

MAINTENANCE

1. Glass Information
   U nder no circumstances should this product be operated with missing or broken glass.
   Donot strike or slam the glass.
   *Do not use abrasive cleaners to clean the glass.

2. Cleaning
   “To clean the unit, first turn off controls on unit and unplug unit from power source.
   “To clean the glass door: remove dust with clean dry cloth or to remove finger prints and other marks clean glass with clean damp cloth. Do not use abrasive cleaners or Spray liquids on glass door surfaces.
   “Metal and metal painted parts should be cleaned with clean damp cloth only. Do not use abrasive cleaners or spray liquids on this surface.

3. If you do not use the heater for a long time, please take out the remote batteries (to prevent corrosion) as shown below. Store the remoteina safe place.

TROUBLE SHOOTING

if the heater will not operate, please check the following before seeking repair of service:

1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the outlet is working.

STORAGE

Store the heater in a cool, dry location when notin use. To prevent dust and dirt build-up, use the original packaging to redack the unit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>