Electrolux EDBMFDXWG Bottom Loading Water Dispenser User Manual

EDBMFDXWG
USER MANUAL

EDBMFDXWG Bottom Loading Water Dispenser

Welcome
Thank you for choosing Electrolux.
Our water dispensers are developed with high technical and quality standards, with features to offer you even more comfort.
Read all instructions before using this appliance. This book contains valuable information about operation, care and service. Keep it in a safe place.
You expect all this from Electrolux….and we deliver.

Environmental advice
The packaging material used is recyclable; we recommend that you separate plastic, paper and cardboard and give them to recycling companies.
According to WEEE (Waste of Electrical and Electronic Equipment) guidelines, waste from electrical and electronic devices should be collected separately.
If you need to dispose of this appliance in the future, do NOT throw it away with the rest of your domestic garbage.
Instead, please take the appliance to the nearest WEEE collection point, where available.

Attention

Inside you will find many helpful hints on how to use and maintain your water dispenser properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your Water Dispenser. You’ll find  many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

• The appliance that you have bought may be slightly different from the one illustrated in this manual. Please refer to the information related to the model you have.
• The appliance you have may carry a different plug than the one illustrated in this manual. The plug that comes with the product follows the electrical specification of the country where it is sold.
• Contact the authorised service technician for repair or maintenance of this unit.
• If the power cord is to be replaced, replacement work shall be performed by authorised personnel only.
• This product was developed for regions with an altitude of approximately 2000 meters. For a higher region, the water boiling point might be too low and cause product damages.

To reduce risk of injury and property damage, user must read this entire guide before assembling, installing and operating dispenser.
Failure to execute the instructions in this manual can cause personal injury or property damage.
This product dispenses water at very high temperatures. Failure to use properly can cause personal injury.
When operating this dispenser, always exercise basic safety precautions, including the following:
WARNING : When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

Safety

For children

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

General safety

• It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move to another house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings.

• Correct functioning of your appliance does not only depend on product quality, but on correct installation by a qualified professional.

• Never remove or damage stickers, warning labels or nameplates attached to the appliance.

• A qualified technician carrying out the installation is obliged to observe applicable national standards and regulations concerning connection to the water distribution system and the electric network. The manufacturer is not responsible for any unprofessional or incorrect installation.
  If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

• WARNING: Do not damage the refrigerant circuit.

• WARNING: To avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions.
  This appliance is intended to be used in household and similar applications such as:
  – staff kitchen areas in shops, offices and other working environments;
  —farm houses and by clients in hotels, motels and other residential type environments;
  – bed and breakfast type environments;
  – catering and similar non-retail applications

• Check that the specifications written on the appliance’s identification plate are the same as those of the electrical power supply.

• This appliance is manufactured and tested in accordance with valid regulations.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

Installation

• Obey the installation instruction supplied with the appliance.
• Remove all the Packaging items.
• Do not install or use a damaged appliance.
• Before first time starting up, check the appliance for any damage incurred during transport.
• Never remove or damage stickers, warning labels or nameplates attached to the appliance.

Water connection

• Make sure to use a new water bottle.
• Make sure the water bottle not faulty – no leakage or holes.
• Make sure to install the bottle as in Catalogue.
• Make sure to use the proper capacity (<20) litre for the water bottle.

Electrical connection

• Only plug the water dispenser directly in the current if it is correctly grounded and with the certain voltage.
• Choose a place that is near a grounded electrical outlet.
• Make sure the appliance is installed correctly. Loose and incorrect electricity mains cable or plug (if applicable) can make the terminal become too hot.
• Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact our Authorised Service Centre or an electrician.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug (if applicable) or to the mains cable. Contact our Authorised Service Centre or an electrician to hangea damaged mains cable.
• The Appliance have electrical switch in the rear side which is set to turn ON or OFF the water heating system only.

Product description

Parts names

Installation

Placement
Use the appliance indoors, where is no likelihood of rain or bad weather, as there is damage risk to the product electrical system.
Place dispenser upright The product must be installed in an easily accessible location in case of repairs.
Place dispenser upright on a flat surface and keep a minimum distance of 25cm from the wall. Make sure that the ventilation openings of the product are not being obstructed.

Assemble

1. Remove drip tray from door and place the grid on top.
2. Snap drip tray and grid assembly into door.

Important
Do not install the water dispenser in a location where there is a direct impact of sunlight or near heat sources, as a stove, oven, etc. Attention
Never turn the appliance upside down or tilt it more than 45°.
Warning
Do not plug in the device unless the water bottle is already installed.

To avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions:

1. Use 13 mm screw to fix the fixing bracket on the middle of bottom cover.
2. Drill out a screw hole(6 mm) on the floor.
3. Insert a screw anchor (wall plug) into the drilled hole.
4. Move water dispenser, Align fixing bracket hole with screw hole of the floor
5. Put the 25mm screw into the screw hole of fixing bracket.
6. Tighten the screw.

Install water bottle

1. Open dispenser door.
2. Place probe assembly on probe hanger.
3. Place fresh bottle outside of cabinet.
4. Remove the entire plastic cap from top of bottle.
5. Clean outside of new bottle with a cloth.
6. Place probe into bottle.
7. Slide collar down until it clicks in place.
8. Push head down until tubes hit bottom of bottle.
9. Slide bottle into cabinet and close door.

Provide electricity
Plug cord into a properly grounded wall outlet.
At this time the pump will begin to move water from the bottle to the hot and
cold tanks. It will take up to 5 minutes to fill the tanks for the first time. During
this period the pump will run continuously. This is normal.

How to use

Activate heating and cooling
This unit will not dispense hot or cold water until the switchers are activated.
To activate, push top side of power switches in to start heating and cooling water.
– If you do not want to heat water, push bottom side of red switch in.
– If you do not want to cool water, push bottom side of green switch in;

Dispensing water
This unit has been tested and sanitized prior to packing and shipping. During transit dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water to prior to drinking any water.
Attention
Sometimes when water is dispensed for more than 2 minutes, the pump fails to take the necessary amount of water, and gets block, in this case the lack of water indicator light on control panel will turn on. If this happens, just open the cabinet door, then close it, and wait for 2 minutes, then the dispenser will return to dispense water.
When the bottle is empty, replace it with a new bottle. (see instructions of how on page 10).

Activate heating and cooling This unit will not dispense hot or cold water until the switchers are activated.
To activate, push top side of power switches in to start heating and cooling water:

• If you do not want to heat water, push bottom side of red switch in.
• If you do not want to cool water, push bottom side of green switch in.

Dispensing water
This unit has been tested and sanitized prior to packing and shipping. During transit dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water.

Hot water
To get the hot water: slide the child safety switch to right, and press hot water button simultaneously.

Warning
Never press more than one button at the same time.

Normal water
To get the room temperature water:
put the cup on the water collector grid and press the natural water button. Cold water To obtain chilled water put the cup on the water collector grid and press the cold water button.

Light indicators
The indicator lights show that the device is working correctly. After connecting the device, check if the indicators are on.

| Indicates when the bottle is empty.
---|---
| Indicates that the water in the reservoir is being heated.
| Indicates that water in the reservoir is being chilled.

Warning

• When the machine is under the ice point and blocked by ice, the cooling switch must be closed for 4 hours before turning it on again to continue its operation.
• This machine should not be turned on until 3 minutes later after turning off the power switch.
• Do not operate or stop the appliance plugged in by the power cord or by pulling on the power cord. Unplug the power cord by holding it by the plug.
• Do not operate or stop the appliance plugged in by the power cord or by pulling on the power cord. Unplug the power cord by holding it by the plug.

Changing bottles
The indicator ( ) lights up when the bottle is empty. Replace the bottle as soon as possible.
Do not dispense hot, cool or cold water if the red light is flashing as you could empty the tanks and cause the dispenser to overheat.

1. Open the dispenser door.
2. Slide empty bottle out of cabinet.
3. Remove probe assembly from empty bottle. Place probe assembly on probe hanger.
4. Set empty bottle aside.
5. Place fresh bottle outside of cabinet. Remove entire plastic cap  from top of bottle. Clean outside of new bottle with a cloth.
6. Place probe into bottle. Slide collar down until it clicks in place. Push head down until tubes hit bottom of bottle.
7. Slide bottle into cabinet and close door.

Cleaning and maintenance

To avoid accident, cut off the power supply before operation according to the following instruction.
The machine had been disinfected before departed from factory. Cleaning the dispenser prior to installing a full bottle of water for the first time.
Cleaning and draining instructions:

1. Making sure the power switch in the 0(off) position and unplug the water dispenser before cleaning.
2. Twist out the two screws, then take down top cover, cold tank cover and separator.
3. Fill 0,6 gallons pure water into cold tank to clean it.
4. Place a large water bucket beneath the drain outlet which on the back of water dispenser, then, remove the drain cover and drain the water.
5. Reposition the drain cover, separator, cold tank cover and top cover after draining. Ensure the pipe and wires are connected properly, then you can use the machine normally.

Attention
The cleaning must be under the guidance of professional staff.
The dispenser heats water to a temperature of approximately 85°C. It can cause severe burns. Please operate it carefully.

Sanitizing

The machine should be disinfected  with disinfectant separately bought from drugstore or marketplace  according to the instruction manual  of the disinfectant and then clean it  with water (see cleaning and draining instructions).

Generally this should be done every  three months.

To remove mineral deposits Mix 1 gallon of water with half  pound of citric acid crystals, inject  into the machine and make sure the water can flow out of the hot water  tap. Switch on the power and heat it  about 10 minutes, 30 minutes later, drain off the liquid and clean it with  water two or three times. Generally this should be done every six  months.

The machine should be disinfected with disinfectant separately bought from drugstore or marketplace according to the instruction manual of the disinfectant and then clean it with water (see cleaning and draining instructions).
Generally this should be done every three months.
To remove mineral deposits
Mix 1 gallon of water with half pound of citric acid crystals, inject into the machine and make sure the water can flow out of the hot water tap. Switch on the power and heat it about 10 minutes, 30 minutes later, drain off the liquid and clean it with water two or three times. Generally this should be done every six months.

Warning
Never disassemble this machine by yourself to avoid risk of damaging machine.
After plug-in each time, if the water not fill in the cold tank fully, the water shortage indicator will blinking and pump is working.
If the water level of the cold tank still fails to reach the limit within 5 minutes, the water shortage indicator will continue blinking, but the water pump will stop working.
In any time, once the cabinet door is opened, the pump should not working.

Troubleshooting

Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling the service technicians, before contacting the service centre please carry out the check listed below.

b)Bonded in different voltage.
c)Lack of electric power or fuse blown.
d)Make sure cold water switch in the rear side of dispenser is ON.
e)Voltage drop.| a)Plug in.
b)Connect in correct voltage.
c)Wait for electric power ON or change fuse.
d)Push the switches to the ON position.
e)Use a voltage stabilizer.
Water not cold from cold tank| a)Electric plug out of the socket.
b)After setup, it will take up to 1 hour to chill the water until minimal set temperature.
c)Make sure cold water switch in the rear side of dispenser is ON.| a)Plug in.
b)Wait one hour for the cold water supply.
c)Push the cold water switch (green) to the ON position.
Water not hot from hot tank| a)Electric plug out of the socket.
b)After setup, it will take up to 15- 20 min to heat the water until maximal set temperature.
c)Make sure hot water switch in the rear of dispenser is ON.| a)Plug in.
b)Wait 15-20 min. for the heat water supply.
c)Push the hot water switch (red) to the ON position.
Excessive heating around dispenser body| a)The appliance very close to a wall.
b)Ventilation vents obstructed.| a)The appliance must be at least 25 cm from the wall.
b)Clear the ventilation vents.
Noise| a)Product leaning on the wall.
b)Uneven placement.| a)The appliance must be at least 25 cm from the wall.
b)Even the appliance.
Water leakage| a)A hole or a crack in the bottle.
b)Overflow in the water collector.
c)Drainage cap not well tightened.| a)Replace the water bottle.
b)Empty the water collector.
c)Tighten the cap.
Steam coming out of
dispenser| a) Excessive heating inside the
hot water tank.| a) Disconnect the main power
source and call service centre.
---|---|---
Unpleasant taste of water| a) Cleaning is made with non recommended material.
b) Poor-quality water.
c) Water bottle shoddy.| a) Follow cleaning/sterilization procedure correctly.
b) Make sure that the mineral water supplier is of good quality.
c) Replace the water bottle.

Technical informations

EDBMFDXWG /EDBMFDXSG
Volt-Freq.| 220-240V – 50/60Hz
Max. power| 500 W
Heating power| 20W
Cooling power| 80W
Cold water| 2L/h(£10°C)
Heat water| 4L/h(290°C)
Environmental temp.| 10~43°C
Humidity| <90%
Net weight| 14.75kg
Prod.dimens. WDH (mm)| 310°374°1040

NOTES

Documents / Resources

| Electrolux EDBMFDXWG Bottom Loading Water Dispenser [pdf] User Manual
EDBMFDXWG Bottom Loading Water Dispenser, EDBMFDXWG, Bottom Loading Water Dispenser, Loading Water Dispenser, Water Dispenser, Dispenser
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>