PawLinx U53 Anti Barking Device No Bark Training Pet Gentle 50FT Remote Control Trainer Handheld Instructions
- May 15, 2024
- PawLinx
Table of Contents
PawLinx U53 Anti Barking Device No Bark Training Pet Gentle 50FT Remote
Control Trainer Handheld
Accessories
Product Overview
Product Characteristics
- Ultrasonic Emission Range: 16.4 – 50 feet
- Charging Method: Type-C_5V
- Charging Time: 2.5 Hours
- Working Mode: Sound Mode, Ultrasonic Mode, Ultrasonic+Flashlight Mode, LED Flashlight Mode
- 2 Ultrasonic Frequencies: FixedFrequency (25kHz), Variable frequency (25KHz-30KHz)
- Sonic Emitter: 3Pcs
- LED Flashlight: 1Pcs
- Sound Mode Duration: 15 Hours
- Ultrasonic Mode Duration (at fixed frequency): 1.5 Hours
- Ultrasonic Mode Duration (at variable frequency): 1.7 Hours
- Ultrasonic+Flashlight Mode Duration (at a fixed frequency): 1.3 Hours
- Ultrasonic+Flashlight Mode Duration(at variable frequency): 1.5 Hours
- LED Flashlight Mode Duration: 28-30 Hours
Product Features
Two Ultrasonic Modes
A human can receive sound from 20 Hz to 20 kHz, while this training device can
emit 25kHz fixed-frequency and 25-30 kHz variable-frequency sound waves that
only dogs can hear. 2 optional ultrasonic training modes can make daily dog
training more effective and deter vicious dogs better. Three Emitters & Wider
Range The device comes with 3 sonic emitters. 3 sonic emitters are more
effective than a single one, extending the control range from 16.4ft to 50 ft.
Extra-bright LED Flashlight
The device is equipped with an extra-bright LED Flashlight, which has a long-
bright mode to illuminate your front in the dark.
Auto-off Safety Function
The device has an automatic shut-off feature, after emitting ultrasonic for 8
seconds, it will automatically stop working to protect our dogs.
Basic Concepts
This ultrasonic dog training device has 4 working modes, including Sound Mode,
Ultrasonic Mode, Ultrasonic + Flashlight Mode and LED Flashlight Mode. And
each of them has a corresponding button to control. Our dog training device
has 2 ultrasonic modes, adjustable by the 2-frequency switch.
Sound Mode
The device will beep for 1 second with one press of the sound mode button. And
it will beep continuously if you hold down the button.
Ultrasonic Mode
The device will emit ultrasonic for 1 second with one press of the ultrasonic
mode button. And it will keep emitting ultrasound if you press and hold the
button. You can select the ultrasonic mode by adjusting the 2-frequency switch
on the side of the device.
Ultrasonic + Flashlight Mode
The device will emit ultrasound and flash the LED Flashlight when you press
the button. This mode will keep working if you press and hold the button. You
can select the ultrasonic mode by adjusting the 2-frequency switch on the side
of the device.
LED Flashlight Mode
More than a dog bark training or deterrent device, our unit can also be used
as a Flashlight to illuminate in the dark. The Flashlight will turn on when
you press and hold the LED Flashlight button for 1.5s, then short press to
change from steady to flashing, and press again to turn it off.
Vibration Feedback
Every time you press the Sound/Ultrasonic/ Ultrasonic+Flashlight mode button,
the device will vibrate in response. Press these buttons once to vibrate once,
and hold them down to vibrate continuously.
Working Indicator Light
- Short press the Sound/Ultrasonic/Ultrasonic + Flashlight Mode button, and the green indicator light will flash. Hold these buttons, and the green indicator light will be on continuously.
- Short press the LED Flashlight mode button, and the green indicator does not flash. Only press and hold the button for 1.5s to turn on the LED Flashlight, then short press the button and the green indicator light will flash.
- When the battery is low, the device will automatically turn off after the red indicator light flashes.
Charging Indicator Light
When charging, the red indicator light will be on continuously. When fully
charged, the green indicator light will be on continuously.
Operation Guide
Step1. Test the Device Please check the device before using it. You could go outside and check if this device will work within 16.4-50 feet.
Checking Guide
Turn on the device by pushing the 2- reposition Switch to the “ “or Then press
the Sound Mode button. If the green LED indicator light flashes, the device is
working.
Tips
If the LED indicator flashes the red light, this device is on a low battery.
Please charge it with the USB cable that comes with the device.
Step2. Use the Device
You can correct your dogs’ unwanted behaviour by using this device. We
recommend you use the Sound Mode at the beginning. Then go to the Ultrasonic
mode and Flashlight + Ultrasonic Mode. The LED Flashlight Mode can be used for
night walks or in darkness.
NOTE
When you use the device, make sure you have turned on the device,
otherwise press any buttons and the device does not respond.
Sound Mode
Hold the device in your hand. When a dog is within 50 feet of you and barks at
you, you can point the device at the dog. And say: Stop! Hush! (Or a similar
command) Then press the Sound Mode Button. The LED green light will flash, and
you will hear a short beep. The device will beep for 1 second with one press
of the sound mode button. And it will continuously rattle the sound if you
hold the button. If the dog still barks at you, press the button again. If
there is no effect, go to the Ultrasonic Mode.
Ultrasonic Mode
Hold the device in your hand. Press the Ultrasonic Mode button once, and the
device will emit ultrasound for 1 second. Press and hold the button, and the
device will emit ultrasound for up to 8 seconds. After sending an ultrasound
for 8 seconds, this device will automatically stop working to protect our
dogs. Our dog training device has 2 ultrasonic modes, adjustable by the
2-frequency switch. Push the switch to the ” ” position, the device can emit
25kHz fixed frequency sound waves; Push the switch to the “ ” position, and
the device can emit enhanced 25kHz-30kHz variable frequency sound waves.
Tip
Under fixed-frequency ultrasonic mode, If there is no effect on deterring
other dogs or training your dog, please choose the variable-frequency
ultrasonic mode, for the enhanced 25kHz-30kHz ultrasonic is easier to
stimulate dog’s ears, and prevent dogs from adapting to fixed-frequency sound
waves, thereby improving the use effect.
Flashlight + Ultrasonic Mode
Hold the device in your hand. The device will emit ultrasound and flash the
LED light when you press the button. This mode will keep working if you press
and hold the button. After sending an ultrasound and flashing the LED light
for 8 seconds, this device will automatically stop working to protect our
dogs. You can change the ultrasonic frequency by adjusting the 2-frequency
switch.
Extra-bright LED Flashlight
Provides maximum illumination, making night walks safer. Please make sure that
the distance between you and the dog is within 50 feet. And there are no
obstacles between you. Once the dog stops barking or behaving badly, please
immediately stop to press the button.
LED Flashlight Mode
To turn on the LED Flashlight, you need to press and hold the button for 1.5,
short press the button, and the device does not respond. After turning on the
LED Flashlight, short press the button to change from steady on to flashing,
and then short press to turn it off.
Precautions
- This ultrasonic dog training device isn’t a toy. Please keep it away from your children.
- Do not immerse this device in water or other liquids.
- Do not use this device on dogs who are under six months old. As their auditory system is still developing, using this device on them may affect badly on them.
- Improper application of this device will be dangerous. Please use this product under our instructions and be careful and patient while training your dog.
Frequently Asked Questions
Q 1: Dose Ultrasonic Affect Other Animals?
A1: It depends on the hearing sensitivity of other animals. For example, this
device may have little effect on cats or birds.
Q2: I have two dogs. One barks a lot, and the other doesn’t. If I use the
device on one of my dogs, will it hurt another?
A2: We will advise you to separate your two dogs before using this device on
one of them. If more than one dog is barking in the house, the sound and
ultrasound from this device will mislead them. So please do not use it on
several dogs at the same time.
Q3: Why this device could only be used on dogs from 6 months to 8 years?
A3: Dogs over eight years old may not hear the ultrasound due to age-related
hearing impairment. Dogs under six months are so small that their auditory
system is still under development. So this device is not suitable for all
dogs. Statistics have shown that this ultrasonic device only can be effective
on 85%-90% of dogs. And some dogs, unfortunately, remain immune to ultrasound.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>