POPULAS Equity-KBL Equity Bi Level with Keyboard Lift Instruction Manual
- May 15, 2024
- POPULAS
Table of Contents
POPULAS Equity-KBL Equity Bi-Level with Keyboard Lift
Product Specifications
- Product: Equity Bi-Level with Keyboard Lift
- Type: Computer workstation with hand-crank adjustment
- Parts Included:
- Leg Package: (2) Legs (A and B), (2) Leg Top Plates, (2) Feet, (4) Toe Caps, (1) Top Crank Assembly, (1) Drive Shaft Assembly, (1) Hardware Bag
- Table Package: (1) Cross Brace, (2) Table Tops
- Hardware Bag Contents: Various screws, washers, levelers, wrenches
Product Usage Instructions
Step One: Unpacking and Identification
Unpack all parts and identify them. Place table tops upside down on a
padded surface.
Step Two: Leg Orientation
Identify legs A and B as shown in the diagram. Ensure shaft couplers face
inward.
Step Three: Attaching Feet
Attach feet to legs using provided fasteners and lock washers. Insert toe
caps and levelers.
Step Four: Cross Brace Installation
Attach the cross brace bracket to the cross brace using the screws provided.
Then attach the bracket to the legs.
Step Five: Mounting Plates
Attach mounting plates to tabletops using specified screws. Install the
Keyboard Surface Lift as shown.
Step Six: Shaft Assembly
Insert hexagonal shafts fully into the legs. Slide washers flush to the
connector tube and center the tube between legs.
Step Seven: Final Adjustments
Gently turn the table over and adjust levelers if needed. Insert the crank
handle and operate the Keyboard Surface Lift. Clean with a soft cloth and mild
furniture cleaners.
Frequently Asked Questions (FAQ)
-
Q: What tools are needed for assembly?
A: You will need a #2 Phillips screwdriver or power driver for assembly. -
Q: How do I adjust the height of the keyboard surface?
A: Use the front lever to raise and lower the Keyboard Surface Lift. Tilt adjustment is made with a knob. -
Q: Can I use casters instead of levelers?
A: Yes, optional casters can be used instead of levelers for mobility.
Parts Included
Leg Package:
- (2) Legs (A and B)
- (2) Leg Top Plates
- (2) Feet
- (4) Toe Caps
- (1) Top Crank Assembly
- (1) Drive Shaft Assembly
- (1) Hardware Bag
Keyboard Surface – Lift Package:
- (1) Keyboard Surface – Lift with Hardware
Table Package:
- (1) Cross Brace
- (2) Table Tops
Tools Needed:
2 Phillips Screwdriver or Power Driver
Hardware
Hardware Bag with
Instructions for models: EQ 361416 KBL, EQ 481416 KBL, EQ 601416 KBL, EQ 4230 CKBL
2720 West Idaho Street Boise, ID 83702 Toll-Free 800-957-2720 Fax 208-362-8009 www.populasfurniture.com
STEP ONE
- Unpack and identify all parts.
- Place table tops upside down on padded surfaces and identify the front edge
STEP TWO
Identify the legs (A and B) and their orientation as shown in the diagram Look
at the bottom of the leg to identify the leg letter (A or B).
Legs must be positioned in the correct orientation to operate. Shaft couplers
face inward.
STEP THREE
Attach leg top plates to legs using four ¼” button head fasteners per plate as
shown.
STEP FOUR
- Attach feet to legs using two 5⁄16″ button head fasteners and lock washers per foot.
- Insert toe caps and levelers.
- Feet are offset to the front of the table
STEP FIVE
Attach cross brace bracket to cross brace using four #8 13/4″ screws as shown.
Attach cross brace bracket to legs as shown.
STEP SIX
Attach mounting plates to tabletops using #10 x 1″ screws.
Attach Keyboard Surface-Lift using #10 x 1″ screws as shown.
Insert hexagonal shafts fully into the legs (front and rear).
Slide washer flush to connector tube and center tube between legs.
STEP SEVEN
- Gently turn the table over and adjust levelers if required.
- Insert the top crank handle through the rear table top directly into the crank tube. The keyboard surface lift raises and lowers with a front lever. Tilt adjustment is made with a knob.
- Clean with soft cloth and mild cleaners suitable for furniture.