VideoRay Fiber Optic Tether Owner’s Manual
- May 15, 2024
- VideoRay
Table of Contents
VideoRay Fiber Optic Tether
Product Information
Specifications:
- Product Name : Fiber Optic Tether
- Mission Specialist Subsea Batteries compatibility
- Mission range : Superior
- Data transmission: High-speed Hydrodynamic influence reduction on the tether
- Includes : 1.5 km Fiber Optic Tether, Terminations, FO Modems, Patch Cables, Tool Kit, Cleaning Kit
Product Usage Instructions
-
Connection Setup:
Ensure all connectors/ports are clean and lubricated before starting. -
Feed the subside termination block of the tether through the port aft frame opening of the device.
-
Secure the tether termination block into the mounting plate using the thumb screw.
-
Remove caps from one end of a patch cable and lubricate both ends.
-
Connect one end of the patch cable to Channel 1 port of the topside termination block.
-
Connect the opposite end of the patch cable to the topside modem’s ST port.
-
Power and Data Connection:
-
Connect and secure the topside modem’s Power and Ethernet cables to the console’s AUX USB and AUX ETHERNET ports.
-
Ensure there is no strain on the fiber optic patch cable connections.
-
Fiber Optic Tether Reel Usage:
-
Connect the standard tether from the reel to the console’s 8-pin whip.
-
Rotate the red Power Mains clockwise to send power to the FO modem.
-
Standard Operation:
Continue with standard connection, power, and function tasks as required for your mission.
FAQ (Frequently Asked Questions)
-
Q: Where can I find detailed installation instructions?
A: Refer to the printed guide included with the Fiber Optic Tether for detailed installation instructions. -
Q: How do I ensure proper maintenance of the Fiber Optic Tether?
A: Ensure ST connectors/ports are clean and all subsea connections are lubricated. Regularly clean and inspect the tether for any damages or wear.
QUICK GUIDE
Mission Specialist Fiber Optic Tether
- VideoRay’s Fiber Optic Tether for use with Mission Specialist Subsea Batteries provides superior mission range and data transmission while significantly decreasing hydrodynamic influence on the tether, resulting in easier piloting and tether management.
- This Quick Guide covers basic connections and use; refer to the printed guide included with the tether for detailed instructions pertaining to installation, connections, and cleaning/maintenance.
Fiber Optic Tether System
- 1.5 km Fiber Optic Tether and Terminations Topside FO Modem
- Submersible FO Modem
- Fiber Optic Patch Cables, 0.5m ST Type Tool Kit
- Fiber Optic Cleaning Kit
Optional Fiber Optic Tether Reel in watertight case
Fiber Optic Tether Guide
Ensure ST connectors/ports are clean and all subsea connections are lubricated
- Feed the tether’s subside termination block upward through the port aft frame opening of the Defender
- Push the tether termination block into the mounting plate rearward and secure with the thumb screw
- Remove caps from one patch cable and generously lubricate both ends with supplied fiber optic lubricant; take note of twist lock coupling and the locating sleeve of the ST Type connectors
- Carefully align and connect one end of the patch cable to the Channel 1 port of the tether termination block
- Carefully align and connect the opposite end of the patch cable to the submersible fiber optic modem’s ST port on the starboard side
- Route and secure any excess patch cable slack
- Connect the submersible strain relief and test all angles to prove NO tension is on the tether
- When using bagged or loose fiber optic tether:
- Carefully align and connect the end of another patch cable to the Channel 1 port of the tether’s topside termination block
- Carefully align and connect the opposite end of the patch cable to the topside modem’s ST port
- Connect and secure the topside modem’s Power and Ethernet cables to the console’s AUX USB and AUX ETHERNET ports
- Secure the topside termination block at the console and ensure there will be NO strain on the fiber optic patch cable connections
- When using the Fiber Optic Tether Reel :
- Connect the standard tether from the reel to the console’s 8-pin whip
- Rotate the red Power Mains clockwise to the on position to send power to the FO modem
- Continue with standard connection, power, and function tasks
