FABTECH FT24265 Cargo Rack Traction Board Mount Kit Instruction Manual
- June 4, 2024
- FABTECH
Table of Contents
FABTECH FT24265 Cargo Rack Traction Board Mount Kit
INSTALLATION INSTRUCTIONS
| FTS24265| TRACTION BOARD MOUNT KIT
---|---|---
2| FT50819| FRONT BRACKET
2| FT50820| REAR BRACKET
2| FT50821| STRAP
1| FT50822| HARDWARE SUBASSEMBLY
| FT50822| HARDWARE SUBASSEMBLY
---|---|---
1| FT24265i| INSTRUCTIONS
1| FT50823| HARDWARE KIT
1| FTAS12| STICKER FT BLUE 10X4
1| FTREGCARD| REGISTRATION CARD
| FT50823 – HARDWARE KIT| LOCATION
---|---|---
8| 5/16-18 X 7/8” BUTTON HEAD BOLT|
18| 5/16” SAE WASHER|
10| 5/16-18 NYLOCK NUT|
2| BALL STUD 5/16”|
CARGO RACK TRACTION BOARD MOUNT KIT
FTS24265
NOTE: TO ORDER WEARABLE REPLACEMENT COMPONENTS DO NOT USE PART NUMBERS SHOWN ON THIS INSTRUCTION SHEET. GO TO FABTECH WEBSITE AND LOOK UP WEARABLE REPLACEMENT PARTS TO FIND THE PROPER PART NUMBER TO ORDER.
TOOL LIST
Required Tools (Not Included)
Basic Hand Tools
Assorted Metric and S.A.E sockets, and Allen wrenches
Torque Wrench
PRE-INSTALLATION NOTES
For technical assistance call:
909-597-7800 or e-mail:
info@fabtechmotorsports.com
READ THIS BEFORE YOU BEGIN INSTALLATION –
Check all parts to the parts list above before beginning installation. If any
parts are missing contact Fabtech at
909-597-7800 and a replacement part
will be sent to you immediately.
INSTRUCTIONS
-
Install FT50819 (Front bracket) to the bottom side and towards the front of the vehicle using the supplied 5/16” hardware. Torque to 25 ft-lbs. SEE FIGURE 1
-
Install FT50821 (Strap) to the front bracket using the screw kit included with the strap. S EE FIGURE 2
-
Install FT50820 (Rear bracket) to the set of holes towards the rear of the vehicle using the supplied 5/16” hardware. Torque to 25 ft-lbs. SEE FIGURE 3
-
Install the supplied ball stud to the rear bracket using the supplied 5/16” washer and nut. Torque to 25 ft-lbs. SEE FIGURE 4
-
Repeat steps on the opposite side of the cargo rack
-
Install your traction boards (not included) by stretching the strap and connecting it to the ball stud. S EE FIGURES 5-6
For technical assistance call: 909-597-7800
Product Warranty and Warnings
Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the vehicle, on which the product was originally installed, for defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings,
bump stops, ball joints, tie rod ends, limiting straps, cross shafts, heim
joints and driveshafts. These parts are subject to wear and are not considered
defective when worn.
They are warranted for 60 days from the date of purchase for defects in
workmanship.
Dirt Logic and Performance Coilover take apart shocks are considered a serviceable shock with a one year warranty on leakage only. Service seal kits are available separately for future maintenance. All other shocks are covered under our Limited Lifetime Warranty.
Fabtech does not warrant any product for finish, alterations, modifications and/or installation contrary to Fabtech’s instructions. Alterations to the finish of the parts including but not limited to painting, powder coating, plating and/or welding will void all warranties. Some finish damage may occur to parts during shipping, which isconsidered normal and is not covered under warranty.
Fabtech products are not designed nor intended to be installed on vehicles used in race applications or for racing purposes or for similar activities. (A “RACE” is defined as any contest between two or more vehicles, or any contest of one or more vehicle against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles, race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranxty are sales outside of the United States of America.
Installation of most suspension products will raise the center of gravity of
the vehicle and will cause the vehicle to handle differently than stock. It
may increase the vehicle’s susceptibility to a rollover, on road and off road,
at all speeds. Extreme care should be taken to operate the vehicle safely at
all times to prevent rollover or loss of control resulting in serious injury
or death.
Fabtech front end Desert Guards may impair the deployment or operation of
vehicles equipped with supplemental restraining systems/air bag systems and
should not be installed if the vehicle is equipped as so.
Fabtech makes every effort to ensure suspension product compatibility with all vehicles listed on the website, but due to unknown auto manufacturer’s production changes and/or inconstancies by the auto manufacturer, Fabtech cannot be responsible for 100% compatibility, including the fitment of tire and wheel sizes listed. The Tire and Wheel sizes listed in Fabtech’s website are only a guideline for street driving with noted fender trimming. Fabtech is not responsible for damages to the vehicle’s body or tires. Fabtech is not responsible for premature wear of factory components due to the installation of oversized tires and wheels.
Fabtech’s obligation under this warranty is limited to the repair or replacement, at Fabtech option, of the defective product only. All costs of removal, installation or re-installation, freight charges, incidental or consequential damages are expressly excluded from this warranty. Fabtech is not responsible for damages and/or warranty of other vehicle parts related or non related to the installed Fabtech product. This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not apply to any product that has been subject to accident, negligence, alteration, abuse or misuse as determined by Fabtech.
Fabtech suspension components must be installed as a complete system including
shocks as shown on our website. All warranties will become void if Fabtech
parts are combined and/or substituted with other aftermarket suspension
products.
Combination and/or substitution of other aftermarket suspension parts may
cause premature wear and/or product failure resulting in an accident causing
injury or death. Fabtech does not warrant products not manufactured by
Fabtech.
Depending on the condition of the factory suspension components retained after the installation of a Fabtech suspension not all vehicles may have the same ride stance front to rear as described in the website. The blue color of suspension components shown in all Fabtech photographs are for display purposes only. Majority of all Fabtech components will be black specifically where noted with part numbers ending in BK.
Installation of Fabtech product may void the vehicles factory warranty; it is the consumer’s responsibility to check with their local vehicle’s dealer for warranty disposition before the installation of the product. Some state laws may prohibit modification of suspension to a vehicle in whole or in part. It is the responsibility of the installer and consumer to consult local laws prior to the installation of any Fabtech suspension product to comply with such written laws.
It is the responsibility of the distributor and/or the retailer to review all warranties and warnings of Fabtech products with the consumer prior to purchase.
Fabtech reserves the right to super cede, discontinue, change the design, finish, part number and/or application of parts when deemed necessary without written notice. Fabtech is not responsible for misprints or typographical errors within the website or price sheet. For the most recent Product Warranty and Warnings visit our website www.fabtechmotorsports.com
Instruction Sheet Part# – FT24265i
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>