FISHER PAYKEL RS6019S2R Integrated Refrigeration Installation Guide

FISHER PAYKEL RS6019S2R Integrated Refrigeration

Product Specifications

• Models: RS6019S2R, RS6019F2L, RS6019S3RH, RS6019F3LJ
• Markets: NZ, AU, UK, IE, SG, HK
• Installation: Integrated Refrigeration

Product Usage Instructions

Safety and Warnings

• Electric Shock Hazard: Always disconnect power supply before servicing or installation to avoid electrical shock.
• Weight Hazard: Be cautious to prevent damage or personal injury while handling the appliance.
• Sharp Edge and Pinch Point Hazard: Watch out for sharp edges and pinch points to avoid injury.
• Tip Hazard: Ensure stability under all loading conditions to prevent damage or injury.

Prior to Installation:

• Do not move the appliance sideways to avoid damaging the rollers or floor covering.
• Avoid exposing the appliance to heat generating appliances like cooktops or ovens.
• Appliance must be installed by a qualified installer or Fisher and Paykel technician.
• All electrical and plumbing connections must comply with local codes and be made by licensed personnel.

Electrical/Plumbing:

• Ensure electrical and water connections are easily accessible for repair or disconnection.
• Use isolating switch for electrical connections if not easily accessible.
• Use isolation valve for water connections if not easily accessible.
• Contact professionals if unsure about installation conditions.

During Installation:

• Keep the appliance door closed when rolling into cabinetry.
• For flush installation, ensure door panels are flush with cabinetry front surface.
• Support all four corners of the appliance firmly on the floor to prevent movement.
• Protect the floor to prevent damage during installation.
• Use low speed, low torque setting when using powered driver for screws.

Frequently Asked Questions (FAQ)

Q: Can I install the appliance myself?
A: It is recommended to have the appliance installed by a qualified installer or Fisher and Paykel technician to ensure proper installation and avoid warranty issues.

Q: What should I do if I encounter difficulty during installation?
A: If you face challenges during installation, contact a professional electrician or plumber for assistance to ensure safe and correct installation.

Q: How do I ensure the stability of the appliance under all loading conditions?
A: Make sure all four corners of the appliance are firmly supported on a level floor to eliminate any movement that could affect stability.

INTEGRATED REFRIGERATION
INTEGRATED RS6019S2R, RS6019F2L, RS6019S3RH
and RS6019F3LJ models
INSTALLATION GUIDE NZ AU UK IE SG HK

SAFETY AND WARNINGS

! WARNING!
Electric Shock Hazard Failure to follow this advice may result in electrical shock or death.
· Read and follow the safety and warnings before operating this appliance.

! WARNING!
Weight Hazard Failure to follow this advice may result in damage or personal injury.
· The appliance is heavy. Please ensure adequate care is taken when installing the appliance.

! WARNING!
Sharp Edge and Pinch Point Hazard Failure to follow this advice may result in injury.
· Take care: panel edges may be sharp. · Do not put fingers in the drawers when closing.

READ AND SAVE THIS GUIDE
WARNING!
To avoid hazard, follow these instructions carefully before Installing or using this appliance. z Please make this information available to the persons installing the appliance. z Assume all electrical parts are live. z Disconnect power supply before servicing and installation.

! WARNING!
Tip Hazard Failure to follow this advice may result in damage or personal injury.
· This product may tip up until it is fully installed. Keep children away and take care.
· This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
To ensure that the appliance is stable under all loading conditions:
· The anti-tip bracket and fittings supplied must be installed by a professional installer according to the installation steps in this guide.

SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
3

PRIOR TO INSTALLATION

z The appliance has front and rear rollers to easily move forward and backward. Do not move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
z Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher.
z The appliance must be installed by a qualified installer, or Fisher and Paykel trained and supported service technician to avoid faulty electrical and plumbing connections.
z All connections for electrical power and grounding must comply with local codes and ordinances and be made by licensed personnel when required.
z All plumbing meeting local codes also required. z Avoid installation of the appliance/s under a ground fault circuit interrupter (GFCI). z Ensure the appliance is installed properly. Improper installation that results in appliance
failure is not covered under the appliance warranty.
ELECTRICAL/PLUMBING z Electrical and water supply connections for these appliances can be located in an
adjacent area or unit (cabinet or cupboard) that is easily accessible in case of repair or disconnection. z Ensure an isolating switch is available if electrical connection is not accessible. z Ensure an isolation valve is available if water connection is not accessible. z Contact an electrical and/or a plumbing professional if you are uncertain the electrical and/ or plumbing conditions for installation.
DURING INSTALLATION
z Ensure the door of the appliance is closed when rolling into the cabinetry. z For flush installation, ensure the door panels are installed flush with cabinetry front surface.
Ensure appliance is properly centred. z Ensure floor is protected to prevent damage. z All four corners of the appliance must be supported firmly on the floor to eliminate any
movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing. z Use low speed, low torque setting when using a powered driver for the screws when fixing or aligning the product.

INSTALLATION MILESTONES
Milestone indicator These milestones represent areas throughout that are pivotal to an optimal installation outcome. These steps require additional installer attention and should be quality checked once completed.
MILESTONE QUICKLINKS
Check anti-tip bracket is correctly installed.
Remove cap from valve before connecting the hose and tightening.
Connect to services and check for leaks.
Push into alcove. Ensure depth gauges touch the alcove front. Adjust product height. Ensure all feet engage with the floor and the upper bracket touches the alcove. Expand spacers. Ensure no gaps are present.
Recheck all gaps and any clashing.
Refer to the installer checklist and complete.

4

Install kit H – UI Trim kit

PARTS REQUIRED

INSTALLATION KIT (INTERNAL BOX)
Install kit D – Kit flow divider

Trim UI RS60 non Hinge RH

Trim UI RS60 non hinge LH

Trim UI RS60 Hinge LH

Trim UI RS60 Hinge RH

Door seal flow divider

Screw SD #7X13 PAN PH ZP

Cap divider flow door

Ball hex key M4

Bolt limiting hinge K08 Install kit A Bracket anti tip assy

Install kit F Kit panel attach

Install kit G – Kit screw panel attachment

Install kit C Kit door screw

Spanner door

L key combi PH2 T25

Install kit B – Kit hinge spacer & depth gauges

Anti-tip bracket

Slider bracket skin DR 60cm

Screw ST 8X5/8 CSK PH AB ZP

Screw MC M5X12 MSH PH ZP

Install kit E – Kit screw alcove attachment

Screw WS #10X35 T17 WFR PH ZP

Spacer bracket side DR 60cm

Twinthread screw 8GX19

Assy hinge spacer A

Assy hinge spacer B

Depth gauge non hinge

Cover hinge spacer A

Cover hinge spacer B Miscellaneous parts

Screw hinge spacer

Plug masonry

Bracket trim side door

Blocker air bypass

5

SP630#10X30MM

60cm

kickstrip

WATER FILTER KIT

PARTS REQUIRED

MISCELLANEOUS ITEMS (MI) PACK

Water filter (comes fitted to product)

NZ AU: Braided Hose, 7X16-24 UNS TO ½” BSP
UK IE SG HK: Braided Hose, 7/16″ x 24 UNS to 3/4″ BSP

JOINER KIT
To be ordered seperately for multiple installation.

Joiner kit A bracket joiner plinth

Joiner kit B bracket joiner top

Joiner kit C bracket joiner rear

Miscellaneous

Safety booklet

Service and Warranty

Ice tray & ice cover (RS6019F2L only)

TRIM KIT

Registration card

Screw M5X12 PH MT STL ZN

Bracket dual connection top

Screw 8GX16 mush washer HD

Trim centre dual install 60cm

MTG PLATE TOE KICK RS60

TRIM SIDE DR 60CM

TRIM SIDE HINGE DR 60CM

Template Panel Door 60cm

Bracket duel plinth FNT (1X)

Screw M5X12 CSKPH NP

Bracket duel plinth FNT (X1)

Bracket duel plinth FNT (2X)
6

Round handle set
Round handle (1) M5x25 Hex screw (2)

HANDLES
MODEL AHSRDSF

OPTIONAL ACCESSORIES
DESCRIPTION Round Handle Kit

Square Fine handle set
Square fine handle (1) M5x25 Hex screw (2)
Professional round flush handle set
Round flush handle (1) M5x25 Hex screw (2)

MODEL AHD5RDSF
AHD5RDSFB

DESCRIPTION

Square fine handle kit Alu
Square fine handle kit BLK

MODEL AHP3RDSF

DESCRIPTION
Professional round flush handle kit

DOOR PANELS

MODEL RD6019

DESCRIPTION
Left or right hinge door panel kit

TOE KICK
MODEL AKRS06010 AKRS12010 AKRS18010

DESCRIPTION Single install toe kick Dual install toe kick Triple install toe kick

7

Required tools Not supplied and must be provided by the installer.

TOOLS REQUIRED
Supplied tools

Powered driver

Flathead screwdriver

Measuring tape

Cross-head screwdriver

Spanner

L key combi PH2 T25

M4 Ball allen key

Cutter

Hacksaw

Hand truck

Socket 8mm

Nut driver

8

PRODUCT AND CAVITY DIMENSIONS
L

4
VERTICAL GAP CLEARANCE FROM SIDE
OF DOOR PANEL

M
E
PLAN VIEW
592
B

DATUM: FRONT OF CHASSIS

DATUM: FRONT OF CHASSIS

579

FH

C

G

A

D

1880

RS6019S2R1 / RS6019S3RH1 Refrigerator with Stainless Steel Panels RD6019, Handle Kit AHD5RDSF and Stainless Steel Toe Kick Panel AKRS06010

NOTE: Left hand hinge is a mirrored version of the image shown. Left hand hinge can be achieved using supplied parts.
RS6019F2L1 / RS6019F3LJ1 Freezer with Stainless Steel Panels RD6019, Handle Kit AHD5RDSF & Stainless Steel Toe Kick Panel AKRS06010

Product Dimensions a Overall height of product B Overall width of product C Overall depth of product (excl. front door panels) D Height from top of door panel to floor E Minimum cabinetry clearance from side of door panel F Minimum cabinetry clearance from top of door panel G Height of door panel H Depth of door panel I Height from floor to bottom of door panel J Depth of toe kick (excl. front door and toe kick panels)

mm 1880 592
579 1877
4 3 1775 19 102 50 ­ 100

Cavity Dimensions

K

K Overall height of cavity

L Overall width of cavity: · Single · Dual · Triple

mm 1880
600 1200 1800

M Minimum overall depth of cavity: · When services are located outside of cavity (shallow) · When services are located in the cabinet above the cavity · When services are located at rear of cavity (deep)

600 610 650

Note: Product shown installed on the floor. Slide into cabinetry position. Alternatively can be installed on a plinth. Adjust your cavity height accordingly. Dimensions may vary by ±2mm

FLOOR

I L
FRONT VIEW

J

M

INDICATES CAVITY CLEARANCES

PROFILE VIEW

INDICATES PRODUCT DATUM

9

PRODUCT AND CAVITY DIMENSIONS
J

4
VERTICAL GAP CLEARANCE FROM SIDE
OF DOOR PANEL

K
D
PLAN VIEW
592
B

DATUM: FRONT OF CHASSIS

DATUM: FRONT OF CHASSIS

579

F

C

E

A
1880

NOTE: Left hand hinge is a mirrored version of the image shown. Left hand hinge can be achieved using supplied parts.
Product Dimensions a Overall height of product B Overall width of product C Overall depth of product D Minimum cabinetry clearance from side of door panel E Minimum cabinetry clearance from top of door panel F Depth of door panel G Height of toe kick panel H Depth of toe kick (excl. front door and toe kick panels)

mm 1880 592
579 4 3
16 ­ 19 100
50 ­ 100

Cavity Dimensions

I Overall height of cavity

J Overall width of cavity: · Single · Dual · Triple

K Minimum overall depth of cavity:

I

· When services are located outside of cavity (shallow)

· When services are located in the cabinet above the cavity

· When services are located at rear of cavity (deep)

mm 1880
600 1200 1800
600 610 650

Note: Product shown installed on the floor. Slide into cabinetry position. Alternatively can be installed on a plinth. Adjust your cavity height accordingly.

For custom panel dimensions refer to page 13. * Custom door panel and toe kick panel to be manufactured and fitted by cabinetmaker. Dimensions may vary by ±2mm

FLOOR
10

G J
FRONT VIEW

H K
PROFILE VIEW

INDICATES CAVITY CLEARANCES INDICATES PRODUCT DATUM

100
FINISHED RETURN CAVITY SIDES & TOP

CAVITY PREPARATION

ALTERNATIVE AREA

ABOVE CAVITY FOR

C

ELEC / WATER CONNECTION

H

A G
E F
D
B
ISO VIEW

NOTE: Left hand hinge is a mirrored version of the image shown.
For ease of installation, ensure cavity has consistent dimensions top to bottom and left to right.
Minimum Cavity Dimensions
a Overall height of cavity
B Overall width of cavity: · Single · Dual · Triple
c Minimum overall depth of cavity: · When services are located outside of cavity (shallow) · When services are located in the cabinet above the cavity · When services are located at rear of cavity (deep)
Minimum required finished return

mm 1880
600 1200 1800
600 610 650 100

Electrical / Plumbing Supply Dimensions d Overall height of supply routing area at rear of cavity Overall width of supply routing area at rear of cavity
E Overall depth of supply routing area at rear of cavity F Height of notch at rear of cavity for services to be routed into adjacent cabinet (either side) G Depth of notch at rear of cavity for services to be routed into adjacent cabinet (either side) H Minimum depth above cavity for services to be routed through

mm 37
600 20 100
55
55

Recommended that services are routed to the adjacent cabinet or either side of the product. Dimensions may vary by ±2mm

11

A D
LEFT HAND SIDE
12

SERVICES
CF

FRONT VIEW

Specifications Electrical Supply Service Plumbing Supply UK IE SG HK NZ AU
Pressure

230 VAC, 50 Hz 10 amp circuit
Water Filter Braided hose, 7/16″ x 24 UNS to 3/4″ BSP Braided hose, 7/16″ x 24 UNS TO 1/2″ BSP
min 275 kPa (40 psi) max 827 kPa (120 psi)

Recommended that services are routed to the adjacent cabinet.

Hose and Cord Lengths Electrical a Power cord length (from the left edge of the product) B Power cord length (from the right edge of the product) C Power cord length (from the top of the product)* Water D Water inlet hose length (from the left edge of the product) E Water inlet hose length (from the right edge of the product) F Water inlet hose length (from the top of the product)

• Excluding plug. Dimensions may vary by ±2mm

mm
1800 2000
380
2450 2000
700

B E
RIGHT HAND SIDE

CUSTOM PANEL DIMENSIONS

C

A

F B
G

ISO VIEW

D
FLOOR
E
PROFILE VIEW

NOTE: Left hand hinge is a mirrored version of the image shown. Left hand hinge can be achieved using supplied parts.
Custom Panel Dimensions a Height of door panel
B Width of door panel: · Single install · Dual install · Triple install
C Depth of custom panel** D Height from floor to top of door panel E Height from floor to bottom of door panel* F Height of toe kick panel G Width of toe kick panel**

mm 1727 ­ 1862
592 594 594.5 16 ­ 19 1877 15 ­ 150 100 597

Maximum weight of door panel*****

19kg

Custom door panel, handle and toe kick panel to be manufactured and fitted by cabinetmaker.

• For further details on multiple installation refer to the planning guide. At 19mm thickness, we recommend an edge radius of 1mm or more to avoid the possibility of panel clash when opening * The grille becomes visible at heights over 100mm *** Can be continuous Includes weight of handle

13

REAR VIEW

54 125 88
50

CUSTOM PANEL PREPARATION
296 256 242 121
36

574 50
1023
1473 1777
50
50

20 90

Ø2.5mm Pilot holes only Do not penetrate front surface

236

60

Custom Panel Preparation Dimensions are shown in millimetres (mm). Dimensions apply for the preparation and installation of custom panels
Handles Ensure handle screw heads are countersunk into back of panel to avoid interfering with hanging bracket, and clear of side brackets as indicated.
Dwg & Dxf Files Dwg and Dxf files of the panel preparation can be downloaded from Trade Resources www.fisherpaykel.com
Template A template for marking and drilling the holes is provided with the product

Do not place handle holes in these locations

For 150mm make 50mm shorter

For 50mm make 50mm longer For 15mm make 85mm longer

BREAKLINE

40

FROM FLOOR TO BOTTOM OF PANEL

592
14

CLEARANCES

D
WALL

B A
WALL
DUAL INSTALL

DOOR CLEARANCES CONSIDERATIONS

C
WALL

E
HINGE TO HINGE Both doors open at the same time – requires space between models

F

F

F

F

F

F

TRIPLE INSTALL

HINGE TO HINGE Only allows a single door open at a time

RS6019S2R1 / RS6019S3RH1 Refrigerator with Stainless Steel Panels RD6019, Handle Kit AHD5RDSF and Stainless Steel Toe Kick Panel AKRS06010
Left hand hinge is a mirrored version of the image shown. Left hand hinge can be achieved using supplied parts.
RS6019F2L1 / RS6019F3LJ1 Freezer with Stainless Steel Panels RD6019, Handle Kit AHD5RDSF & Stainless Steel Toe Kick Panel AKRS06010

Clearance Dimensions
a Depth of door (90° open, measured from front of cabinetry)
B Minimum door clearance to adjacent wall (90° ­ reduced internal access)* *
C Minimum door clearance to adjacent wall (115° ­ full internal access)
D Minimum cabinetry clearance from side of door panel to adjacent wall (non hinge side)
E Minimum clearance between products when opening hinge to hinge. Allowing both doors to open at the same time

mm 600
80
273
4
100

Minimum Door Clearance (Vertical Gap)

mm

F Dual Install:

· Stainless steel door panels (gaps equalized

5

during installation)

· Custom panels (width of custom panel increased to

4

maintain 4mm gap across multiple products)***

G Triple Install:

· Stainless steel door panels (gaps equalized

6

during installation)

· Custom panels (width of custom panel increased to

4

maintain 4mm gap across multiple products)***

• Use hinge limiting pin to restrict door opening to 90° where necessary ** Minimum dimensions shown are for the contemporary handle kit AHD5RDSF. Custom panel and handle details need to be taken into account. *** Refer to `Custom panel dimensions’ and Multiple Install pages for further details.

G

G

G

G

G

G

G

G

INDICATES CAVITY CLEARANCES INDICATES PRODUCT DATUM
15

CHECK CAVITY

PRIOR TO INSTALLATION

CHECK PANELS

Measure alcove dimensions. Ensure all

minimum specs have been met.

Ensure all door and toe kick panels

1

If alcove depth is greater than 610mm,

1

are square and set up to the correct specifications. Refer to `Custom panel

a spacer will need to be installed

preparation’ for details.

alongside the anti-tip bracket. Refer to

page 18 for details.

2

Check alcove is square and is secured to

the wall. Ensure front of alcove is square to the top of the alcove and the floor

2

is flat.

Ensure all bracket and handle holes have been pre-drilled. Refer to `Custom panel preparation’ for details.

3

Ensure a finished return has been created.

Ensure services are accessible and

4

correctly installed. Refer to `Services’

for details.

16

UNPACK PRODUCT

z Keep all packing materials until the unit has been inspected.

z Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage.

4

z Fisher & Paykel is not responsible for shipping damage.

Cut the straps, lift the top cap

1

off and cut down the side of the

5

carton to remove. Dispose of

packaging responsibly.

2

Remove all pre packaged parts and set aside. Do not discard.

6

Push the grille flap to open and unscrew

the 2 screws behind the flap and 5 on

3

the grille. Set screws aside. Open the

7

door and pull the grille outwards from

the product.

Using a Phillips screwdriver, unscrew the transit brackets from one side of the product and set aside.
Check levelling feet have been raised, tilt product and insert handtruck. Restrain product to handtruck. We recommend using the corner posts to protect the product when using restraints.
Remove the two remaining transit brackets.
Tilt product onto handtruck and remove palette. Move product to the installation location. Remove and discard corner posts.
17

INSTALL ANTI-TIP BRACKET

For solid wall installs:

1

Check for wall stud.

5

Using the bracket as a guide, predrill four holes into the wall or spacer.

Secure bracket using crosshead screws.

Install kit A

For masonry wall installs:

Using the bracket as a guide, pre-drill

2

Measure the depth range of the alcove

ensuring the minimum depth range has

6

been met.

four holes into the wall. Hammer four masonry plugs into the wall until flush before securing the bracket using crosshead screws.

Install kit A

Ensure that the anti-tip bracket is

3

If required, install a spacer at the rear of the cavity to bring depth to 600mm.

7

installed correctly to prevent the possibility of the appliance tipping

forward when the door is opened.

4

Measure the height from floor to the front overhang and mark on rear wall.

18

HINGE SWAP (OPTIONAL)

Open the door and remove the door

shelves. Loosen the hinge screws

1

using the supplied Torx T25 driver.

5

Check plates are positioned correctly.

Slide the door out and place onto a

protected surface.

2

Carefully remove hinges from door and

set aside.

6

Swap hinges as illustrated. Ensure base of hinge is parallel and tightened securely.

Remove top cover and set aside.

Refit top cover.

Install kit D

3

Push on the edge of the outside plates, lift out and swap to the other side.

7

Swap alcove bracket with the hinge bracket. Secure using 3 screws at the top of the cabinet.

4

Use a flathead screwdriver to remove

the inside plates. Move to the other side ensuring the rounded corners face

8

the inside.

Slot the door back onto the screws and tighten using a torx key to tightly secure. Refit the door shelves.

19

JOIN PRODUCTS (MULTIPLE PRODUCT INSTALLS ONLY)

1

Roll products into position.

5

Secure the bracket at the rear top using four screws.

Joiner kit C

2

Secure the bracket at the front base using four screws.

6

Repeat process for additional products.

Joiner kit A

3

Secure the bracket at the front top using four screws.

Joiner kit B

4

Secure the bracket at the rear base using four screws.

Joiner kit A 20

DEPTH GAUGES & SPACER

INSERT HINGE LIMITING PIN (OPTIONAL)

Clip both hinge spacers onto the product.

Ensure spacer A is fitted to the top of

the product and spacer B is fitted to

To limit the door opening to 90, lower

1

the bottom of the product, for right-

1

the hinge limiting pin into the upper

hand hinge installations and vice versa

and lower hinges.

for left-hand hinge installations.

Install kit B

Install kit H

Using the supplied crosshead screws,

2

fit the depth gauges at the the top &

bottom of the door as shown.

Install kits B & C

Multiple product installs:

3

Fit either the depth gauges or spacers at the top and bottom of the product

based on your installation as shown.

21

SERVICE CONNECTIONS OUTSIDE ALCOVE

Connect to tap and turn on. If water is

1

Route the hose from rear of product through to front corner.

5

running, check for leaks.

Connect to outlet and turn power on.

2

Remove the cap from the valve before connecting the hose and tighten.

If required, wrap a thread around the

3

hose and power cord to bring any slack inside the plinth and reduce the risk of

them tangling behind the product.

Push product into alcove while pulling

the hose and power cord. Ensure the

4

gauges touch the alcove end, the

hose doesn’t kink and the power cord

remains free and untangled.

22

SERVICE CONNECTIONS INSIDE ALCOVE

1

Route the hose from rear of product through to front corner.

5

Connect to outlet and turn power on.

Push product into alcove. Push in until

2

Remove the cap from the valve before connecting the hose and tighten.

6

the gauges touch the alcove end. Ensure hose doesn’t bend or kink and that the

power cord is not trapped.

3

Connect to tap and turn on. If water is running, check for leaks.

If required, wrap a thread around the

4

hose and power cord to bring any slack inside the plinth and reduce the risk of

them tangling behind the product.

23

1

ADJUST HEIGHT IN CAVITY

Front view

Profile view – alcove alignment

Turn the righthand screw to adjust the rear of the product followed by the lefthand screw to adjust the front. Turn clockwise to raise and anti-clockwise to lower.
Ensure feet engage with the floor and the upper bracket touches the alcove.

1

Multiple product installs:

Beginning with the outside feet, turn the

righthand screw to adjust the rear of the

product followed by the lefthand screw

2

to adjust the front. Once product is set

2

in cavity, adjust the central feet.

Ensure feet engage with the floor and the upper bracket touches the alcove.

Ensure all depth gauges are flush to the front of the alcove.

3

Where this is not possible:

3

Measure the distance between the chassis front and the alcove front as shown, ensuring it is 62mm.*

Plan view

4
24

Open the door and use the supplied hex

key to expand the spacers. Ensure no

4

gaps are present.

Install kit D

*assuming panel thickness of 19mm.

SECURE PRODUCT
Open the door and secure following the sequence shown. The longer screws should be used where shown in blue, and the smaller screws where shown in red. Ensure a gap between drill and product is maintained to avoid cosmetic damage.
Install kit B & H
Snap the ends off both spacers.
Clip covers onto spacers. Ensure cover A is fitted to spacer A and cover B to spacer B.
Install kit B
Unscrew the crosshead screws to remove depth gauges. Set aside.

DOOR PANEL PREP CUSTOM PANEL

Recheck door panel size and

1

specifications ensuring all bracket locations have been marked. Refer to

5

Align the side brackets to panel.

page 14 for details.

Install kit F

2

Remove the top cover using a powered driver. Set aside.

6

Using the screws supplied in the install kit, secure the door panel bracket using seven screws.

3

Remove both washers and nuts and set

aside. Lift the panel brackets outwards

7

to remove.

Secure the side brackets using two screws per bracket. Ensure side brackets are fitted tightly and the fasteners are secured straight.

4

Align the centre door panel bracket to

panel ensuring the `V’ in bracket is to sit

8

on the centreline.

Secure the handle to the panels using 4xM5x25 hex screws per handle. Ensure handle fixings do not interfere with side brackets.

25

DOOR PANEL PREP STAINLESS STEEL PANEL

Remove all blue tape from the panel.

Determine the panel orientation

based on the hinge and handle

Align side brackets to the pre-drilled

1

positions. Red labels indicate left hinge

5

installations, blue labels indicate right

holes based on your hinge orientation. Red labels indicate left hinge

hinge installations.

installations, blue labels indicate right

hinge installations.

2

Remove the top cover using a powered driver. Set aside.

6

Using the screws supplied in the panel kit, secure the door panel bracket using seven screws.

Secure the side brackets using two

Remove both washers and nuts and set

screws per bracket from the supplied

3

aside. Lift the panel brackets outwards

7

panel kit. Ensure side brackets are

to remove.

fitted tightly and the fasteners are

secured straight.

Determine the panel orientation

4

based on the hinge and handle

positions. Red labels indicate left hinge

8

installations, blue labels indicate right

Plug the unused holes in the panel using the remaining screws from the panel kit.

hinge installations.

26

ALIGN DOOR PANEL

SECURE DOOR PANEL

Ensure side brackets are disengaged

Ensure top mounting screws have

and the top mounting screws have

1

been loosened and sit at their

1

been loosened. Rotate the mounting

lowest position.

studs clockwise to lower the panel and

anticlockwise to raise it.

Install kit D

2

Locate the top of the door to the two mounting screws and lower.

2

Loosely tighten the side screws and the top M8 washers using the spanner and L key provided in the install kit.

Install kit D

We recommend loading the shelves in

Push panel side-to-side to adjust

3

the door with 15kg weights to ensure

3

horizontally. Ensure panels are flush with

accurate panel gap widths.

front of cabinet.

Fit side screws to panel using the short

crosshead tool provided in the install

kit. For 90° door opening installs, the

4

Using a piece of tape, fit a tab on the

door to assist in opening the door

4

supplied crosshead key should be used on the hinge-side.

without disturbing panel settings.

Tighten all side screws and the top M8

washer and nut to secure.

Install kit D 27

SECURE DOOR PANEL

FIT TRIMS AND GRILLE

Open the door and loosen the lower

bracket screw. Adjust the bracket until it

Fit the top cover using two screws.

5

rests against the door panel. Re-tighten

1

Ensure flat side faces out from

the screw and fit an additional screw to

the panel.

secure to panel.

Install kit E

Locate the shorter door trim to the

6

Recheck all gaps and any clashing.

2

hinge-side of the product, and slide down to clip in place. If a gap is present,

remove and readjust the side brackets.

Locate the longer door trim to the non-

hinge-side of the product and slide

3

down to clip in place. If a gap is present, remove and readjust the side brackets.

Ensure trim does not protrude above

the top cover.

Hinge swap installs only:

4

Swap the bottom hinge and non-hinge

trims on the grille.

28

FIT TRIMS AND GRILLE

CENTRE TRIM INSTALL (MULTIPLE PRODUCT INSTALLS ONLY)

Locate trim between products. Lower

5

Fit the top UI trim taking into account the hinge location.

1

trim before pushing in to ensure bottom connector bracket clears the grille. Slide trim up until it slots into the

top bracket.

Install kit H

Open the cover and align the grille to

the product. Slot into place starting

6

with the base of the grille. Hand tighten the top left screw first, followed by the

2

Ensure top of trim touches alcove before securing using the supplied fastener.

top right screw. Fit the remaining five

screws on the grille to secure.

Joiner kit A

29

TOE KICK PANEL PREP

Recheck toe kick panel size and

1

specifications. Refer to page 13

1

for details.

Measure distance from floor to bottom

of grille to determine the position of the

2

toe kick mounting plate. Secure supplied toe kick mounting plate

2

in trim kit to the toe kick panel.

Install kit E

3

4
30

SECURE TOE KICK
Loosen the screws on both toe kick depth adjustment brackets.
Slide both depth adjustment brackets all the way forward and slightly tighten the screws.
Attach the toe kick to the depth adjustment brackets. The magnets should auto- locate.
Push the toe kick back to the desired depth before removing. If toe kick depth is less than 90mm, attach the additional foam block. Hand tighten the depth adjustment screws and refit the panel.

SECURE TOE KICK

WI-FI SET UP

Your appliance may be connected to your home wireless network and operated remotely using the app.

z Ensure your home Wi-Fi network is turned on.

Measure the distance between the

z You will be given step by step guidance on both your appliance and mobile device.

5

bottom of the door and the base of the door panel. Cut the flow divider

z It may take up to 10 minutes to connect your appliance.

to length.

On your mobile device:

Install kit D

1 Download the app from www.fisherpaykel.com/connect 2 Register and create an account. 3 Add your appliance and set up the Wi-Fi connection.

Fridge

4.0°C

6

1
Align flow divider to the screw at the bottom of the door and slot into place. Secure to the door panel using the

Freezer
-18.0°C

Press to display the menu.

provided screws.

2

Settings

Press or to scroll through the list and select SETTINGS.

Press

to confirm.

Cut the seal to length and clip onto the

7

front of the flow divider. Ensure tabs on

the seal and flow divider align.

3

Wi-Fi Setup

Press or to scroll through the list and select WI-FI SETUP. Press to confirm.

8

On the UI, press and hold to exit

installer mode.

4

To complete connection, follow the app instructions
Connect

Open the FISHER & PAYKEL app on your mobile device. Follow the onscreen guidance.
31

FLUSH WATER THROUGH THE WATER DISPENSER

1

Ensure power and water connections have been turned on.

1

FLUSH WATER THROUGH THE ICE MAKER
Ensure power and water connections have been turned on.

Press the water dispenser pad and

Fridge

2

dispense a total of 8 Litres of water. A harmless carbon residue may be

2

4.0°C
Freezer

Press to display the menu.

dispensed with the water during

-18.0°C

this process.

When dispensing for long durations, a

Press or to scroll through the list

3

time out period may occur where an

3

Ice
ON

alarm will sound. Please wait 2 minutes

and select ICE.

Press

to turn ice maker on.

before dispensing again.

The flushing process will be complete

after the first full bin of ice is produced.

4

We recommend discarding this batch of

ice as it may appear slightly discoloured

and contain a harmless carbon residue.

32

REPLACING WATER FILTER

INSTALLER CHECKLIST

Hinge limiting pins have

Installer mode has been

been fitted if required

1

Push grille flap to access filter. Pull tool outwards to remove.

exited

All covers are in place

All panel gaps and any potential clashing points have been checked

All trims have been secured at all attachment points

2

Using the filter tool, rotate filter 90 anti-clockwise to unlock and remove.

Product is robustly attached to cabinetry

Levelling feet have been adjusted and engaged

If water is turned on, purge before first use

Remove packaging. Ensure filter handle

3

is positioned horizontally and push all the way in. Rotate clockwise to lock

into place.

Complete and keep for safe reference:

Model

Serial no.

Purchase date

Purchaser

Dealer address

Installer’s name

4

Slot tool into place and push to close the grille flap.

Installer’s signature

Installation company

Installation date

33

SAFE PRODUCT REMOVAL

1

Empty contents.

Remove the flow divider and panel

2

bracket before removing all door panel side screws and the M8 washer and nut.

Lift panel up and out to remove.

Reverse the installation process to remove

3

from alcove. Ensure doors are taped shut

and safe handling practices are observed.

34

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets
and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
867868B 08.23

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Connected Living | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>