FANELITE FANDC52LN Ceiling Fan User Manual

: May 15, 2024
: FANELITE

FANELITE FANDC52LN Ceiling Fan

FANELITE-FANDC52LN-Ceiling-Fan-PRODUCT

Product Information

Specifications

Brand: Fanelite
Model: Ceiling Fan with LED Light
Website:www.fanelite.com

Product Usage Instructions

Unpacking Check

Before assembling your ceiling fan, ensure all components are present:

Hanger bracket
Upper canopy
Blades
Lower canopy
Receiver
Wood screws for fixing hanger bracket (for wood ceiling)
Blades screws
Balancing kit
Remote control, wall support, washers, and screws

Fix the Ceiling Hanger Bracket For Concrete Ceiling:

Position the support in the desired location and mark the holes
to be made.
Drill the concrete structure with 2 holes corresponding to the
diameter of your anchor studs.
Introduce the anchor studs using a hammer (leave the threaded
rod sticking out).
Replace the support and secure it with nuts and washers.
Tighten securely using a wrench.

Procedure for Changing the Tube

Remove the black boxes (magnetic rings) from the wires.
Remove the screw and lower the hanger ball.
Remove the axis, hanger ball, upper canopy, lower canopy, pins, screws/nuts, and safety cut-off device.
Remove the 18 cm tube.
Reverse the steps for re-assembly based on the tube length change.

Assembly

Place the motor block on a stable surface.
Position each blade on the motor block (blades snap into place) and secure them using provided screws.
Tighten the screws carefully to avoid blade damage but ensure they are properly tightened to prevent excessive vibration during start-up.

Frequently Asked Questions (FAQ)

Q: How do I change the light settings on the ceiling fan?

A: The light settings can be adjusted using the remote control provided with the fan. Refer to the user manual for specific instructions on changing light modes and brightness levels.

Q: Can I install this ceiling fan on a sloped ceiling?

A: Yes, this ceiling fan is designed to be installed on sloped ceilings. Follow the instructions provided in the manual for proper installation on a sloped surface.

YOUR NEW APPLIANCE Dear Client,

Thank you for choosing this product. This very innovative and very designed product has been designed to provide you with maximum comfort and security.
Before using your appliance, and for correct and safe use, please read this manual carefully and strictly follow the safety instructions below.
Keep this manual in a safe place so that you can consult it if necessary.

IMPORTANT SAFETY INSTRUCTIONS

Please read the safety instructions carefully before using your appliance.
To reduce the risk of fire, electric shock, personal injury, and damage, read and strictly follow the instructions below:
This appliance is not intended for use by people (including children) whose physical, sensory, or mental capacities are reduced, or by people without experience or knowledge, unless they have been able to benefit, by the intermediary of a person responsible for their safety, surveillance or prior instructions concerning the use of the appliance.
Children must not play with the appliance. Children must not carry out cleaning and user maintenance without supervision. Children should be supervised to ensure they do not play with the appliance.
Never leave unattended children near the appliance or persons with disabilities. Never leave infants, elderly, or sick people under the airflow of the appliance.
Never leave children to play with polythene bags or wrapping film, risk of choking.
Keep the appliance in a cool, dry place out of the reach of children, the elderly, and the disabled.
For safety reasons, never leave the appliance unattended while it is working.
The minimum distance between the floor and the blades must be at least 230 cm.
The ceiling fan hanger bracket must be fixed to the ceiling to support a minimum weight of 68 kg. The fixing must be made securely in the ceiling structure.
Never put your hands and/or objects into the passage of the blades. Avoid contact with moving parts.
Never cover the appliance when it is connected to a power supply.
This appliance is designed and intended exclusively for domestic use and on a flat and dry surface.
Due to its construction, this appliance is not intended for outdoor use, or indoor use only.
Remove all items from the package and remove the adhesive tapes preventing the op-eration of the appliance before use.
Assemble the appliance completely before using it. Under no circumstances should it be connected to the power supply before it is fully assembled and ready for use.
Electrical connections must be made by current regulations and by a qualified electrician.
Before any electrical connection and to avoid any risk of electric shock, switch off all power supplies and put them back into service only when the installation is finished.
Connect the appliance to an electrical supply providing a current whose specifications (voltage, frequency, etc.) are identical to those indicated on the appliance’s rating label. Check that the voltage of your electrical installation corresponds to that of the appliance before connecting it.
A way of disconnection must be provided in the electrical installation per the installation rules.
This appliance must be connected to an effective grounding system.
If the power cable is damaged, it must be replaced by the manufacturer, its after-sales service, or persons of similar qualifications to avoid a hazard.
Never unplug or move the appliance by pulling on the power cable. Turn off and unplug the appliance before moving it. Carry the appliance in its original packaging.
Regularly and rigorously inspect the appliance and do not use it if it is damaged or if you see any deterioration or malfunction. Do not use it if its blades or electrical wires are damaged, if it dropped, or if it has been damaged in any other way. In this case, contact an authorized repair center or qualified person to make the service and reparation of the appliance.
In the event of abnormal noise, smell, or smoke, immediately stop the appliance and call an authorized repairer.
Do not use water or detergent to clean the appliance. A dry cloth will be preferable. Before cleaning, be sure to switch off the power supply.
This appliance is intended for use in an area with good air circulation, and should not be used in a closed room without air circulation.
This appliance can be used only inside a sheltered room.
Do not use the appliance in a damp place, near a shower, swimming pool, or bathtub…Do not immerse the appliance or power cable in water or any other liquid. Do not expose the appliance to water spray, or splashing water.
This appliance is not intended for use in barns, stables, or similar rooms.
Do not place the appliance in or near a heat source. The appliance must not be used in places where the presence of flammable vapors or explosive dust is likely.
If you plan to not use your appliance for a long time, turn it off and disconnect its power supply.
Use only FANELITE spare parts.
The light source contained in this luminaire should only be replaced by the manufacturer or its maintenance agent or a person of equivalent qualification.
This appliance complies with current European safety standards.

Your appliance works with a battery-operated remote control

Batteries must be kept out of the reach of children.
The batteries must be correctly installed respecting the polarity. Check the (+) and (-) poles.
Used batteries must be removed from the remote control and replaced by new ones. Do not mix old batteries with new ones or different types of batteries. Replace the batteries only with new batteries of the same type.
Check that the battery compartment cover is properly closed. The danger of explosion if batteries are incorrectly replaced.
Never use batteries with electrolyte leaks or cracks. Do not swallow the battery. If the battery is swallowed, seek medical advice immediately. Never short the battery poles. Never try to open the batteries.
Batteries should not be exposed to excessive heat. Batteries should never be thrown into the fire, they could explode.
Non-rechargeable batteries should never be recharged.
Remove the batteries from the remote control before disposing of the remote control when it is no longer functional, or during long periods of non-use.
The batteries must be replaced under the regulations in force regarding disposal. Please bring used batteries to a dedicated recycling center where they will be treated in an environmentally friendly manner.
Any intervention on the appliance by an unqualified person is prohibited.

GUARANTEE

Contact your distributor to find out its guarantee terms.
All FANELITE appliances are guaranteed against manufacturing and parts defects insofar as they are working under normal operating conditions.
Our appliances must be installed by qualified professionals under the regulations in force and the instructions given in these operating and assembly instructions.
FANELITE reserves the right to apply or not the guarantee in case of negligence of the customer, defective installations, poorly adapted or not in conformity with the regulations in force.

Any damage related to any of the following points can not be taken into consideration and covered by our guarantee:

Defects of supervision, maintenance, and maintenance.
Maintenance due to normal wear and tear.
Maintenance of the product is not under the instructions in the manual.
Any adaptation of the product that would be necessary for compliance with the technical or safety standards applicable in a country other than that for which the product was originally designed and manufactured.
Use or installation that does not conform to the use for which the product is intended or to the technical or safety standards in force in the country where it is used.
Non-observance of instructions, safety precautions, and instructions stipulated in the manual.
A case of force majeure, sinister (fire, flood, etc.), lightning, etc.
A modification or repair of the product not carried out by a qualified professional.
Use of parts and accessories not compatible with the product or defective.
Immediate or delayed damages resulting from improper handling during transport, mishandling, falling, shock, contact with water, sand or any other substance, etc.
Improper treatment of the product due to inappropriate environment (poor aeration, exposure to moisture or strong heat, vibration, non-adapted power supply, surge, etc.).
Whether with respect to the purchaser, installer or any other person, our company cannot under any circumstances be held liable for any physical or material damage of any kind whatsoever, which may be caused by our products or which would be the direct or indirect consequence of the use of our products.

NOTES

In most houses, the ceiling fan is placed in the center of the room, replacing a light. In this way, the ceiling fan provides evenly distributed airflow throughout the room.
Since a ceiling fan typically requires no more power than a light, the existing electrical circuit should not be overloaded. But if the ceiling fan is equipped with lamps, make sure the electrical circuit is strong enough to support the load.
If this is not the case, you will need to install a new circuit with a new circuit breaker on the main electrical panel or an auxiliary panel so that the ceiling fan has its circuit without powering any other device.
If there is no central light in the room, you will need to define a location where the ceiling fan will be installed and carry electricity.
A connection box is required. Never use a plastic box.
FANELITE ceiling fans can weigh up to 25 kg with accessories. Make sure that your ceiling fan hanger bracket is firmly attached and that your installation can support a weight of at least 68 kg.
For your safety and that of others, please check the weight of your ceiling fan and adjust the resistance of your installation if necessary. The ceiling fan hanger bracket must be supported by the ceiling structure.
Your installation must also be able to withstand the vibration caused by your ceiling fan when it is working. Even a well-balanced ceiling fan causes vibration when it works.

HEIGHT UNDER BLADES

The minimum recommended distance between the floor and the blades is 230 cm. You can use a meter to check this height (level of your floor / lower limit of the blades).
If the distance between the floor and the blades is less than the minimum recommended above or if the structure of your interior does not meet this minimum, check the length of the tube of your ceiling fan, it is sometimes possible to shorten it by a few centimeters. Do not forget, however, that a distance of 25 cm between the blades and the ceiling, ideally more, is needed to promote good air circulation and optimal brewing.
If, on the other hand, you need an extension down rod to lower the level of your ceiling fan (high ceiling), please contact your retailer, there are extensions of 90 cm.

UNPACKING CHECK

Before assembling your ceiling fan, remove all parts from the package and make sure that all of the following components are present:

Hanger bracket
Upper canopy
Blades
Lower canopy
Receiver
Wood screws for fixing hanger bracket (wood ceiling)
Blades screws
Balancing kit
Remote control, wall support, washers and screws

FIX THE CEILING HANGER BRACKET

WARNING : The fixing must be done securely in the structure of the ceiling by a qualified person. Depending on the structure of your ceiling, use suitable screws and washers. Do not fix the ceiling support in a structure thinner than 50 mm or in hollow elements, to avoid any risk of falling. Make sure that the fixing is very solid and can support at least 68 kg by pulling it. We decline all re-sponsibility in the event of a fall of the ceiling fan.
You can install the hanger bracket on an inclined ceiling of 15° maximum. If your ceiling is inclined, the lugs of the hanger bracket must be on the highest side of your ceiling. Do not put it on the lowest side of your ceiling.

WOOD CEILING

Position the support in the desired location and fix it using the screws provided.

CONCRETE CEILING

Position the support in the desired location and mark the holes to be made. Remove the support and drill the concrete structure by making 2 holes corresponding to the diameter of your anchor studs.
Remove dust and introduce the anchor studs using a hammer (leave the threaded rod sticking out). Remove nuts and washers, replace the support, and replace the washers and nuts.
Tighten the nuts securely using a suitable wrench.

PROCEDURE FOR CHANGING THE TUBE

Please follow the steps below if you wish to change the included 18 cm tube to the optional 10.5 cm or 90 cm tubes. FANELITE-FANDC52LN-Ceiling-Fan-
FIG-4

ASSEMBLY

To fix the blades, place the motor block so that it is stable. Often, the polystyrene foam used for motor pack-aging can make excellent support on your worktop.
The motor/tube/canopy / LED kit is pre-assembled.
Position each blade on the motor block (the blades snap into place) and use the screws provided to secure them.
Caution, tighten the screws carefully to avoid damaging the blades, but be sure to tighten properly to prevent excessive vibration during start-up.

HANG THE CEILING FAN

HANG THE CEILING FAN IN THE HANGER BRACKET
- Take your ceiling fan and put the hanger ball at the top of the tube into the hanger bracket.
- Turn the tube until the hanger ball locks into the hanger bracket (concave groove of hanger ball into the lugs of hanger bracket).
- Be careful to not damage the electrical wires and not pinch them between the hanger ball and the hanger bracket.
- A = Concave groove of hanger ball
- B = Lugs of the hanger bracket
- C = Hanger bracket
INSTALL THE SECURITY CABLE
- For more security, fix the security cable provided, ideally to an element independent of the fixing (beam …), or for example on an anchor stud with a hook of concrete ceiling.

INSTALL THE RECEIVER IN THE CEILING HANGER BRACKET

Once your ceiling fan is installed in the hanger bracket, slide the receiver into the hanger bracket (above the hanger ball).

ELECTRICAL CONNECTIONS

WARNING : Before proceeding to the electrical connections, carefully read the safety instructions in this manual.
Before any electrical connections, switch off all power and restart only when the installation is completed.
Electrical connections must be made under current regulations and by a qualified electrician.
Once the receiver is installed in the hanger bracket, make the electrical connections below (See diagram on next page)

CONNECTIONS FROM CEILING FAN TO RECEIVER
- Connect the connector of the ceiling fan (MOTOR – 3 wires: grey/blue/black) to the receiver.
- Connect the connector of the ceiling fan (LED – 3 wires: white/yellow/red) to the one of the receiver.
- Connect the connector of the ceiling fan (CUT-OFF DEVICE – 2 wires) to one of the receivers.
CONNECTIONS FROM RECEIVER TO HANGER BRACKET
- Connect the connector of the hanger bracket (2 wires: brown or black/blue) to the receiver.
- The brown or black wire corresponds to the phase (Line), and the blue wire corresponds to the neutral.
CONNECTIONS FROM THE HANGER BRACKET TO THE AC CEILING POWER
- Carefully install the sleeves provided on your ceiling wires (phase and neutral) to ensure double insulation.

By using the connecting terminals provided on the hanger bracket:

Connect the phase of the ceiling to the phase of the hanger bracket in the domino L (LINE: black or brown wire of the hanger bracket).
Connect the neutral of the ceiling with the neutral of the hanger bracket in the domino N (NEUTRAL: blue wire of the hanger bracket).
Check that all electrical connections have been correctly made and that the receiver and the wires are prop-erly stored in the hanger bracket.

INSTALL THE CANOPY

Once the electrical connections have been made, mount the canopy against the hanger bracket, place it correctly on the hanger bracket, and turn it until it locks in place.
Be careful to not damage/pinch the electrical wires.

INSTALL THE BATTERIES IN THE REMOTE CONTROL

NOTE : If you intend to not use your remote control or ceiling fan for a long time, we advise you to remove the batteries from the remote control to preserve it.
The remote control works with 2 batteries 1,5V AAA. To insert the batteries or change the batteries when they are empty:
Slide the battery compartment cover (on the back of the remote control) downwards to remove it. Insert 2 batteries 1,5V AAA by respecting the polarity. Close the cover by sliding it upwards.

USE OF THE REMOTE CONTROL

DESCRIPTION
- FAN Turn On/Off the fan
- Increase the speed
- Decrease the speed
- LIGHT Turn On/Off the light
- Change the color temperature of the light
- Increase brightness
- Decrease brightness
- TIMER Set timer
- MODE F/R Short press: Select mode Long press (~ 3 seconds): Change the running direction of the blades – Summer/winter mod
USE OF THE REMOTE CONTROL
- Power On / Off FAN Press this button to turn on or off your ceiling fan. Your ceiling fan starts by default at speed 3.
- Speed setting Press this button to increase the speed (5 speeds, speed 1 is the lowest, speed 5 is the highest). The number of bars visible on the screen corresponds to the selected speed.
- Press this button to decrease the speed (5 speeds, speed 1 is the lowest, speed 5 is the highest). The number of bars visible on the screen corresponds to the selected speed.

LED light setting

LIGHT Press this button to turn on or off the LED light.
Press this button to change the temperature of the light (3000°K / 4000°K / 5000°K).
Press this button to increase the light intensity.
Press this button to decrease the light intensity.
Timer setting TIMER Press this button to set the timer (automatic stop after the selected time has been reached). Each time this button is pressed, the timer increases by one hour (12 hours max).
The selected time is displayed on the screen. To deactivate the timer, press until the screen of the remote control shows no more time or manually turn off the ceiling fan.
Mode setting MODE F/R
Press this button to change the ventilation modes. By default, the ceiling fan starts in normal mode.
NORMAL : The ceiling fan operates normally depending on the speed selected. No indicator is displayed on the screen.
SLEEP : The ceiling fan automatically decreases its speed by one level every 30 minutes. Select the starting speed before activating SLEEP mode. The MODE SLEEP indicator is displayed on the screen when this mode is activated.
ECO: The ceiling fan operates in eco mode at a high energy efficiency level, between speeds 1 and 2. The ECO MODE indicator is displayed on the screen when this mode is activated.
Note: When the ECO or SLEEP modes are activated, the speed buttons do not work.
Summer / Winter mode MODE F/R Press and hold this button for 3 seconds to change the running direction of the blades. By default your ceiling fan rotates counterclockwise (summer mode).
This mode allows the room to be refreshed by sending the cold air down and hot air to the top. The winter mode, meanwhile, will allow you to heat the room by sending hot air down (the blades turn in the opposite direction, clockwise).
The indicator F or R will be displayed on the screen.
F forward = S = Summer = counterclockwise rotation
R reverse = W = Winter = clockwise rotation
NOTE: The ceiling fan is equipped with a safety cut-off protection device, which automatically stops the motor in the event of abnormal balancing or shock in the blades.
If necessary, check the ceiling fan then manually turn the ceiling fan on again using the remote control.

PAIRING PROCEDURE REMOTE CONTROL / RECEIVER

By default, the remote control and the receiver are already paired together.

If the remote control is not con-nected to the receiver, please follow the steps below:

Turn off the power of your ceiling fan using the circuit breaker or switch or AC power receiver’s connector.
Wait a few seconds then turn on the power again.
Within 20 seconds of turning on the power, press and hold the FA N button of the remote control for around 8-10 seconds.

The receiver beeps when the synchronization is complete. You will then be able to use your remote control to control your ceiling fan.
4/ PAIR THE REMOTE CONTROL ON SEVERAL CEILING FANS
When several FANDC52LN ceiling fans are installed, it’s possible to control all of them with only one single remote control.
Repeat the above procedure PAIRING PROCEDURE REMOTE CONTROL / RECEIVER with all the other ceiling fans that you want to synchronize on the same remote control.

INSTALL THE WALL SUPPORT OF THE REMOTE CONTROL

Install the supplied wall support by using screws and washers adapted to the structure of your wall so that you can store your remote control on its wall support.

CLEANING AND MAINTENANCE

WARNING : Before cleaning your appliance, carefully read the safety instructions in this manual.
We recommend that you keep your unit clean and clean it at least once a month.
Do not use water or detergent to clean your ceiling fan. A dry, soft cloth will be preferable to avoid scratching the body of your ceiling fan and the blades.
Vacuum dust from inaccessible places.
It is recommended to regularly check the condition of the ceiling fan and ceiling fan hanger bracket (at least twice a year depending on use).
Due to frequent use of the ceiling fan, the screws will tend to loosen a little bit over time.
Check and tighten the screws of the ceiling bracket, blades, motor cover, and LED kit if necessary.

TROUBLESHOOTING

NOTE : Visit our Frequently Asked Questions section (www.fanelite.com) for more information.
The ceiling fan (motor) starts and then stops after a few seconds:
This is a safety mode of the receiver because the blades are not installed. Install the blades before using your ceiling fan.

The ceiling fan no longer works:

Check the battery status of your remote control. Change the batteries if necessary and your ceiling fan will re-operate normally.
If, despite the changed batteries, your ceiling fan still does not work, check the condition of the circuit breakers. If the ceiling fan circuit breaker is OFF, put it back to ON. If the circuit breaker trips OFF again, do not touch it, leave the power off, and call a qualified electrician.
The remote control and the receiver may maybe unpaired. Refer to the USE OF THE REMOTE CONTROL section to perform the pairing procedure again.
If your receiver beeps several times when you press a button on the remote control, this is an error code and this means that your receiver has locked out. To reset it, turn off the power of your ceiling fan by using the circuit breaker or switch, wait 1 minute, and then turn on the power again.
Check your electrical connections. Refer to the ELECTRICAL CONNECTIONS section. Check that all met-al wires and pins are securely engaged in their connectors. It sometimes happens that one of the wires and and one of the metal pins is slightly recessed in the connector preventing the operation of the ceiling fan. Push on the wires if necessary to fully engage them in the connectors. Check that the current is coming through your ceiling AC power supply. Check that no electrical wires are damaged.

The ceiling fan oscillates abnormally during operation:

A ceiling fan vibrates naturally when it is working. Even a well-balanced ceiling fan causes vibration when it works.

Check the condition of the screws of the blades and tighten them if necessary.
Check that the hanger ball is securely locked in the hanger bracket (concave groove of the hanger ball into the lugs of the hanger bracket).
If your ceiling fan still oscillates abnormally when it is working, it may be because the blades are not well balanced. In this case, use the balancing kit supplied with your ceiling fan to re-balance them. To identify the defective blade, turn off your ceiling fan, put the plastic pliers on the edge of the blade, and turn on your ceiling fan. Repeat by changing position and blade if necessary until normal operation of the ceiling fan is resumed. Once the correct position is found, glue the weight at the level of the pliers (onto the blade) then remove the pliers.

For more information, visit our website www.fanelite.com, or contact us. See the ADDITIONAL INFORMATION section.

TECHNICAL SPECIFICATIONS

Reference: FANDC52LN (white model) / FANDC52LN-BK (black model)
Power source: 220-240 V~ 50/60 Hz
Light: LED 20W 3 colors (3000°K 1640 Lumens / 4000°K 1770 Lumens / 5000°K 1820 Lumens) Max noise level : 43 dB
Max airflow: 12 108 m3/h
Protection class: II
Package dimensions : 65 x 40 x 25 cm
Gross weight: 5,70 kg
Net weight: 4,40 kg
Power: 18 Watts
Diameter: 132 cm

ENVIRONMENT PROTECTION

Instructions on environmental protection

Do not dispose of this product in the usual household garbage at the end of its life cycle; hand it over to a collection point for the recycling of electrical and electronic appliances.
The symbol on the product, the instructions for use, or the packing will inform about the methods of disposal. The materials are recyclable as mentioned in its marking.
By recycling or other forms of re-utilization of old appliances, you are making an important contribution to protecting our environment.
Please inquire at the community administration for the authorized disposal location.

CONFORMITIES

The company LOGIFAN SARL and FANELITE EUROPE SAS declares its FANDC52LN and FANDC52LN-BK products to comply with the following directives in force from the European Parliament:
Directive on the harmonization of the laws of the Member States relating to electromagnetic compatibility: 2014/30/UE
Directive on the harmonization of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits: 2014/35/UE
Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment: 2011/65/UE
Directive on the harmonization of the laws of the Member States relating to the making available on the market of radio equipment: 2014/53/UE
The full declaration of conformity for the product is available at the following address https://www.fanelite.com/produit/fandc52ln or https://www.fanelite.com/produit/fandc52ln-bk or on request by e-mail.

ADDITIONAL INFORMATION

This manual is also available online on our website: www.fanelite.com You want to contact us by email: contact@fanelite.com
You want to contact us by phone : (+590) 590 29 44 64
You can also contact us by using the contact form on our websites. Imported and distributed by :

LOGIFAN SARL