RYOBI RY18LT23A Cordless Grass Trimmer User Manual
- May 15, 2024
- RYOBI
Table of Contents
RY18LT23A Cordless Grass Trimmer
User Manual RY18LT23A
RY18LT23A Cordless Grass Trimmer
Important!It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.
Subject to technical modification
RY18LT23A-0
|
---|---
|
|
|
|
|
Product specifications
Product specifications
Cordless line trimmer
Model
Voltage
No-load speed
Cutting capacity
Cutting line diameter
Cutting capacity (flailing blade)
Vibration level (in accordance with EN 50636-2-91 Annex BB)
Line trimmer
Rear handle
Front handle
Uncertainty
Flailing blade
Rear handle
Front handle
Uncertainty
Noise emission level (in accordance with EN 50636-2-91 Annex CC)
Line trimmer
A-weighted sound pressure level
Uncertainty
A-weighted sound power level
Uncertainty
LWA + KWA
Flailing blade
A-weighted sound
pressure level
Uncertainty
A-weighted sound power level
Uncertainty
LWA + KWA
Battery and charger
Model
Battery pack
Charger
Compatible battery
packs
Compatible chargers
Replacement part
1.6 mm cutting line
Complete spool (3 pcs)
Heavy-duty blades
Heavy-duty replacement
blades
NOTE:Visit your local special orders desk or contact RYOBI Customer
Service for replacement parts.
WARNING
The declared vibration total values and the declared noise emission values
given in this instruction manual have been measured in accordance with a
standardised test and may be used to compare one tool with another. They may
be used for a preliminary assessment of exposure.
The declared vibration and noise emission values represent the main
applications off the tool. However, if the tool is used or diferent
applications, used with diferent accessories, or poorly maintained, the
vibration and noise emission may differ. These conditions may significantly
increase the exposure levels over the total working period. An estimation of
the level of exposure to vibration and noise should take into account the
times when the tool is turned of or when it is running idle. These conditions
may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration and noise, such as maintaining the tool and the accessories,
keeping the hands warm (in case of vibration), and organising work patterns.
RYOBI WARRANTY APPLICATION CONDITIONS
In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.
-
The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
-
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
-
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
— any damage to the product that is the result of improper or lack of maintenance
— any product that has been altered or modified
— any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
— any damage caused by non-observance of the instruction manual
— any product not displaying the CE approval mark on the rating plate
— any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
— any product connected to improper power supply (amps, voltage, frequency)
— any product used with inappropriate fuel mixture (fuel, oil, ratio of oil/ fuel mixture)
— any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
— normal wear and tear spare parts
— inappropriate use, overloading of the tool
— use of non-approved accessories or parts
— Accessories provided with the tool or purchased separately including but not limited to blades, saw chains, cutting lines, etc.
— Any periodic adjustments to or maintenance cleaning of carburettors
— Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc. -
For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
-
This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
Any request or issue with the product can be addressed to your local
authorised service centres (visit www.ryobitools.eu) or directly to:
Techtronic Industries GmbH, Max Eyth Strafle 10, 71364 Winnenden, Germany.
Please state the serial number and product type printed on the label.
EC DECLARATION OF CONFORMITY
Cordless line trimmer
Brand: RYOBI | Manufacturer¹ | Model number² | Serial number range ³
We declare as the Manufacturer under our sole responsibility that the product
mentioned below fulfills all the relevant provisions of the following European
Directives, European Regulations and harmonised standards⁴
Measured sound power level……………………………. 92.6 dB(A)
Guaranteed sound power level……………………………. 95 dB(A)
Conformity assessment method to Annex VI Directive 2000/14/EC amended by
2005/88/EC.
Notified body⁵
Authorised to compile the technical file:⁶
-
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany -
RY18LT23A
-
47592801000001 – 47592801999999
-
2006/42/EC, 2014/30/EU, 2000/14/EC, 2005/88/EC, 2011/65/EU, EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019, EN 50636-2-91:2014, EN IEC 55014-1:2021, EN IEC 55014-2:2021, EN IEC 63000:2018, EN 62233:2008
-
No. 0197 – TÜV Rheinland LGA Products GmbH
Tillystraße 2 – 90431 Nürnberg – Germany
Todd Chipner
Vice President, Quality – Asia
Winnenden, Dec. 23, 2021
- Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
Cordless line trimmer
Brand: RYOBI
Model number: RY18LT23A
Serial number range: 47592801000001 – 47592801999999
fulfills all the relevant provisions of the following Regulations: S.I.
2008/1597
(as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended), S.I.
2001/1701 (as amended) and that the following designated standards have been
used:
BS EN 60335-1:2012+A2:2019, BS EN 50636-2-91:2014,
BS EN IEC 55014-1:2021, BS EN IEC 55014-2:2021,
BS EN IEC 63000:2018, BS EN 62233:2008
Measured sound power level: 92.6 dB(A)
Guaranteed sound power level: 95 dB(A)
Conformity assessment method to S.I. 2001/1701 Schedule 9 (as amended)
Approved body:
No. 8500 – AnP Certification Limited
2 Parkfield Street, Rusholme, Manchester, M14 4PN, United Kingdom
Todd Chipner
Vice President, Quality – Asia
Winnenden, Dec. 23, 2021
Authorised to compile the technical file:
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
RYOBI is a trade mark of Ryobi Limited, and is used under license.
Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK 961478263-01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>