eXcellence 782 Sewing Machine

Product Information

The eXcellence 782 sewing machine is a versatile household appliance designed to meet your sewing needs. With a range of features and accessories, this machine offers convenience and precision for your sewing projects.

Product Usage Instructions:

Safety Instructions:

Before using the eXcellence 782 sewing machine, it is crucial to follow these safety guidelines:

• Never leave the appliance unattended when plugged in.
• Avoid using the sewing machine as a toy, especially around children.
• Use only recommended attachments and accessories.

Setting Up the Machine:

Follow these steps to set up your eXcellence 782 sewing machine:

1. Place the machine on a stable surface.
2. Plug in the power cord to a suitable electrical outlet.
3. Refer to the owner’s manual for specific threading instructions.

Sewing Operations: To start sewing with the eXcellence 782, follow these general steps:

1. Select the desired stitch pattern on the machine.
2. Position the fabric under the presser foot.
3. Lower the presser foot and begin sewing at a steady pace.

Frequently Asked Questions

• Q: Can I use the eXcellence 782 sewing machine outdoors?
  • A: No, this sewing machine is intended for indoor household use only. Avoid using it outdoors.
• Q: How should I clean and maintain the eXcellence 782?
  • A: Refer to the owner’s manual for specific cleaning instructions. Regular maintenance will help prolong the life of your sewing machine.

“`

eXcellence 782
Instruction Book

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the following: This sewing machine is designed and manufactured for household use only. Read all instructions before using this sewing machine.
DANGER– To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.
WARNING– To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.
2. Use this appliance only for its intended use as described in this owner’s manual. Use only attachments recommended by the manufacturer as contained in this owner’s manual.
3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and foot controller free from accumulation of lint, dust and loose cloth.
5. Never drop or insert any object into any opening. 6. Do not use outdoors. 7. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered. 8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet. 9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 10. Keep fingers away from all moving parts. Special care is required around the sewing machine
needle and/or cutting blade. 11. Always use the proper needle plate. The wrong plate can cause the needle to break. 12. Do not use bent needles. 13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break. 14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as
threading the needle, changing the needle, threading the bobbin or changing the presser foot, and the like. 15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any other adjustments mentioned in this owner’s manual.
SAVE THESE INSTRUCTIONS
For Europe only: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. For outside Europe (except U.S.A.): This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance. (EEA (European Economic Area) and UK)

ESSENTIAL PARTS

Names of Parts
(1) Thread take-up lever (2) Reference chart (3) Top cover (4) Touch panel stylus holder (5) Foot compartment (6) Bobbin thread cutter B (7) Bobbin winder spindle (8) Bobbin thread cutter A (9) Hole for extra spool pin (10) Spool pin (11) Spool holder (large)

(12) (13)
(14) (15)

(16) (17)

(18)

(19) (20)

(12) Retractable sewing light (13) Face plate (14) Needle threader lever (15) Thread cutter/holder (16) Extension table (accessory storage) (21) (17) Needle plate release lever (18) Holes for circular pivot pin (19) Feed balancing dial (20) Knee lifter socket (21) Visual touch screen
(22) Speed control slider (23) Start/stop button (24) Reverse button (25) Auto-lock button (26) Needle up/down button (27) Presser foot lifter button (28) Thread cutter button

(25) (26) (27) (28)

(24)

(23) (22)

(29) (30)

(44) (45)

(43)

(42)

(41)

(31)
(32) (33) (34) (35)

(29) Stitch width adjusting dial (30) Stitch length adjusting dial
(31) Lower thread guide (32) Needle clamp screw (33) Needle bar thread guide (34) Needle (35) Zigzag foot A (36) Needle plate (37) Hook cover release button (38) Hook cover plate (39) Bobbin thread cutter (40) Feed dogs (41) Foot holder (42) Thumbscrew (43) Lever (44) Buttonhole lever (45) Needle threader guide

(40) (39)

(38) (37) (36)

4

(46)

(47)

(48) (49)

(50)

(51)

(55)

(52) (53) (54)

(46) Carrying handle

(47) Handwheel

(48) Dual feed balancing dial

(49) Ventilation openings

(50) Thread cutter switch jack (51) USB port

(58)

(52) Drop feed lever

(53) Machine socket

(54) Foot control jack

(57)

(55) Power switch

(56) Dual feed drive

(57) Presser foot lifter

(58) Attachment connector cover

(56)

NOTE:

· To carry the sewing machine, hold the carrying

handle with your hand, and support the sewing

machine with the other hand.

· Sewing machine design and specifications are

subject to change without prior notice.

Standard Accessories

No.

Part Name

Part No.

1 Zigzag foot A (set on the machine) 859802006

2 Overcasting foot M

859810007

3 Satin stitch foot F

859806011

4 Blind hemming foot G

859807001

5 Zipper foot E

859805009

6 1/4 seam foot O

859814012

7 1/4 seam foot O (without guide)

202313104

8 Automatic buttonhole foot R

862822013

9 Stabilizer plate

859832016

10 Rolled hem foot D

859804008

11 Open-toe satin stitch foot F2

859813000

12 Darning foot PD-H

859839002

13 Darning foot PD-H (open-toe)

859839013

14 Professional grade foot HP

865803006

15 Free motion quilting closed-toe foot QC 859836009

16 Free motion quilting open-toe foot QO 859837000

17 Free motion quilting zigzag foot QV 859812009

18 Variable zigzag open-toe foot QZ

862895006

19 Ruler work foot QR

862896007

20 Button sewing foot T

859811008

21 Button shank plate

832820007

22 Dual feed holder

859817015

23 Dual feed foot AD

859819109

24 Dual feed plus professional foot HP2 865522008

5

(29)

(25)

(26)

(30)

(27)

(28)

(31)

(32)

Standard Accessories

No.

Part Name

25 A.S.R. case

26

A.S.R. (Accurate Stitch Regulator) with ASR-QC

27 A.S.R.

28 A.S.R. closed-toe foot ASR-QC

29 A.S.R. open-toe foot ASR-QO

30 A.S.R. clear-view foot ASR-QV

31 A.S.R. ruler work foot ASR-QR

32 A.S.R. instruction card

Part No. 869408010
868835006
868835017 868837008 868837101 868837204 868837307 103334A01

(1) (5)
(9) (13)

(2)

(3)

(4)

(6)

(7)

(8)

(10)

(11)

(12)

(15)

No.

Part Name

1 Bobbin x 5* (1 set on the machine)

2 Needle set

3 Lint brush

4 Seam ripper (Buttonhole opener)

5 Quilting guide bar

6 Screwdriver

7

Spool holder (large) x 2* (1 set on the machine)

8 Spool holder (small) x 2*

9 Spool holder (special) x 2*

10 Extra spool pin

11 Touch panel stylus

12 Circular pivot pin

13 Needle plate (set on the machine)

14 Hook cover plate

15 Straight stitch needle plate

16 Hook cover plate

17 Professional grade needle plate HP

18 Hook cover plate (HP)

19 Accessory case

Part No. 102261103 859856005 802424004 647808009 755802001 820832005
822020503
822019509 862408008 809146000 860194002 849801004 861606016 809136100 862817118 809136100 865805019 809136A01 866801018

• This is a part number of single item (not set number).

(14) (17)

(16) (19)

(18) 6

(20)

(21)

(22)

(23) (26)

(24)

(25)

No.

Part Name

20 Instruction book

21 Threading guide sticker

22 Dust cover

U.S.A. and Canada

23

Power supply cable**

U.K. Australia

Continental Europe

24 Cloth guide

25 Extra wide table

26 Knee lifter

Part No. 869800407 101506A08 858802069 856519004 830377008 830314018 830335004 858401008 865812008 846417022

** The power supply cable included may differ from the illustration.

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

No.

Part Name

1 Foot control

2 Thread cutter switch

3 Cable tie

Base plate 4
*Rubber sole x 6**

5 Setscrew A x 4**

6 Setscrew B x 2**

7 Washer x 2**

8 Rubber sole x 2**

Part No. 043170108 865810006 767849306 767849100 525010005 000081005 865045002 000072508 525010005

• Rubber sole x 6 are already attached on the under side of the base plate.
  ** This is a part number of single item (not set number).

Instructional Video
A presentation video with quick-start information for this model is available online and can be accessed using the following QR code.
https://www.youtube.com/playlist?list=PLzURYW7eSwbGCTc2tRbWKe5sG0kPfkkCz

Download application for PC

You can design and create your own stitch patterns.

• This application is for PC only.

https://global.elna.com/excellence-782-stitch-composer/

StitchComposer

Optional accessories Optional accessories for this model are avaialble by accessing the following QR code.

Optional accessories

7

(2) (2)

(1) (3)

Extension Table The extension table provides an extended sewing area and can be removed for free-arm sewing.
(1) Extension table (2) Free-arm
To detach: Draw the table out to the left. To attach: Slide the table on the base and push the table to the right.
Free-arm Sewing Free-arm sewing is used for stitching sleeves, waistbands, pant legs or any other tubular garments. It is also useful for darning socks or mending knees or elbows.
(3) Free-arm

Accessory Storage
The accessories can be conveniently stored in the accessory case, the compartments of the extension table and the compartments under the top cover.

To store the accessories in the compartment of the

extension table, hook your fingers in the hollow on the left

side of the extension table. While holding the extension

(1)

table with the other hand, pull it open in the direction of

the arrow to open it.

(1) Foot compartment

(2) Stabilizer plate

(3) Automatic buttonhole foot R

(4) Straight stitch needle plate

(5) Professional grade needle plate HP

(6) Bobbin

(7) Dual feed foot AD

(8) Dual feed plus professional foot HP2

(3)

(9) Extra spool pin

(10) Circular pivot pin

(4)

(5)

Other accessories can be also stored in the compartment

in the extension table.

(6)

(1)

(10)

(7) (8) (9)

Accessory Case
To store the other accessories, open the accessory case and store in the appropriate places. Optional accessories can also be stored in this case.

8

1. 2.
(2)
(1)
(3)

(4)

(5)
4.

Extra Wide Table To attach: 1. Screw the adjusting screws into the legs. 2. Peel off the backing paper from the rubber soles and
attach to the bottom of the legs. (1) Adjusting screw (2) Leg (3) Rubber sole
3. Attach the 6 legs to the table top with the setscrews. (4) Setscrew (5) Table top
4. Remove the extension table.
5. Place the assembled table on the machine.

6. Adjust the height of the table top by turning the

adjusting screw.

loosen

tighten

To remove: To remove the legs from the table top, you do not have to loosen the setscrews. Turn the leg clockwise to remove the leg from the table top.
To attach the leg to the table top again, insert the leg into the attachment of the leg, then turn the leg counterclockwise until it stops.
9

(1) (3)

Foot Control and Thread Cutter Switch
To attach the foot control and the thread cutter switch to the base plate, tighten setscrews, and setscrews with washers as shown.
(1) Foot control (2) Thread cutter switch (3) Base plate (4) Setscrew A (5) Setscrew B (6) Washer
(2)

(4)

(4)

(5)

(6)

Adjusting the Thread Cutter Switch Position

Placing the thread cutter switch to the left.

The thread cutter switch position can be adjusted for your convenience.

If you wish to attach the thread cutter switch to the left side of the foot control, follow the procedure below.

NOTE: A Phillips head screwdriver is not included with this machine.

1. Remove the setscrews A, B and washers with a Phillips head screwdriver.

(1) (1)

(2)

(3)

(1) Setscrew A (2) Setscrew B
(3) Washer

2. Turn the base plate 180 degrees.

3. Attach the foot control and thread cutter switch

with the setscrews and the washers. Tighten the

setscrews A and B. Be sure that the cable is not

caught between the foot control and the base plate.

(1) Setscrew A (2) Setscrew B
(3) Washer

(2)

(3)

(1)

(1)

10

Adjusting the horizontal position of the thread cutter switch

1. Loosen the setscrews under the switch.

(1) Setscrew

(2) Washer

(2) (1)

2. Slide the switch to the left or right, and fix it at the

desired position by tightening the setscrews with a

screwdriver.

1. 2.
(2) (5) (4)

Adjusting the vertical position of the thread cutter switch

1. Remove the setscrews and washers.

2. Move the switch forward or backward, attach the

(3)

switch at the desired position and fix it with the setscrews and washers.

(1) Setscrew (2) Washer
(3) Desired position

(1)

NOTE:

· To fix the thread cutter switch at its lowest position,

(6)

fix the setscrews into the hole (4), and then holes (5). · Tighten the setscrews securely.

· Peel off the backing paper from the rubber sole (6)

and attach it to the bottom of the thread cutter switch

as shown.

11

GETTING READY TO SEW

Connecting the Power Supply

Using Start/Stop Button

1. 1. First make sure the power switch is off.

2. Insert the machine plug of the power supply cable

(1)

into the machine socket.

3. Insert the power supply plug into the wall outlet, and turn the power switch on.

(3) 2.
(2)

(1) Power switch (2) Machine plug (3) Machine socket (4) Power supply plug (5) Wall outlet

3. (5)
(4)

NOTE: · Make sure to use the power supply cable that came
with the machine. · If you turn off the power switch, wait for 5 seconds
before turning it on again.
WARNING:
· While in operation, always keep your eyes on the sewing area, and do not touch any moving parts such as the thread take-up lever, handwheel or needle.
· Always turn off the power switch and unplug the machine from the power supply: – when leaving the machine unattended. – when attaching or removing parts. – when cleaning the machine.
· Do not place anything on the foot control.

Before Using Your Sewing Machine
Before using your sewing machine for the first time, place a scrap of fabric under the presser foot and run the machine for a few minutes. Wipe away any oil which may appear.
Operating Instructions:
The symbol “O” on the switch indicates the “off” position of the switch.
For the U.S.A. and Canada only Polarized plug (one blade wider than the other): To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If it does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

12

(1)

(5)
3. (4)
(2)

(3)

4. (7)

(6)

Using Foot Control
If you wish to use the foot control, pull out the cord from the foot control and insert the pin connector into the jack on the machine.
1. First make sure the power switch is off.
2. Insert the machine plug of the power supply cable into the machine socket.
3. Draw out the cord from the foot control and insert the pin connector into the foot control jack on the machine.
4. Insert the power supply plug into the wall outlet, and turn the power switch on.
(1) Power switch (2) Machine plug (3) Machine socket (4) Pin connector (5) Foot control jack (6) Power supply plug (7) Wall outlet
NOTE: The start/stop button does not work when the foot control is connected.

13

Thread Cutter Switch

(1)

If you wish to use the thread cutter switch, insert the pin connector into the thread cutter switch jack on the

machine.

1. First make sure the power switch is off.

(6)

2. Remove the cable tie from the cable.

(5)

3. Insert the machine plug of the power supply cable

into the machine socket.

4. Insert the pin connector into the thread cutter switch

4. (3)

5. (8)
(7)

jack on the machine. 5. Insert the power supply plug into the wall outlet, and
turn the power switch on.
(1) Power switch (2) Cable tie

(4)

(3) Pin connector

(2)

(4) Thread cutter switch jack

(5) Machine plug

(6) Machine socket

(7) Power supply plug

(8) Wall outlet

After sewing, depress the thread cutter switch on the right side of the foot control to trim both the needle and bobbin threads.

Do not depress the thread cutter switch until the start/

stop button turns blue (2).

(1)

(1) Thread cutter switch

NOTE:

· The thread cutter switch does not work without the

foot control being depressed first.

· Bundle the cables with the cable tie as necessary.

(2)

(3) Cable tie

(3) 14

(1)

(2)

(3)

Controlling Sewing Speed Speed Control Slider You can limit the maximum sewing speed with the speed control slider according to your sewing needs. To increase the sewing speed, move the slider to the right. To decrease the sewing speed, move the slider to the left. The sewing speed can be changed while stitching.
Foot Control
Pressing on the foot control can vary sewing speed. The harder you press the foot control, the faster the machine runs.
NOTE: · The machine runs at the maximum speed set by
the speed control slider when the foot control is fully depressed. · You can select the desired start-up speed from slow, medium or high (refer to page 143). · This machine is equipped with an automatic shutdown safety feature to prevent overheating whenever the machine is running overloaded. Follow the safety instructions that appear on the visual touch screen.
Cord storage The cord of the foot control can be conveniently stored in the cord storage under the base cover of the foot control.
(1) Base cover (2) Cord (3) Hooks
Operating Instructions: Foot control model 21380 is for use with this sewing machine.

15

(3) (4) (5) (6)

(7)

(8)

(2)

(3) Auto-lock button · When the following stitch patterns are selected:
Utility Applique Quilt Bridge Decorative

(1)
Machine Operating Buttons (1) Start/stop button Press this button to start or stop the machine. The machine starts running slowly for the first few stitches, then runs at the speed set by the speed control slider. The machine runs slowly as long as this button is pressed. The button will turn red when the machine is running, and blue when it has been stopped. Pressing and holding this button while sewing will slow down the sewing speed and the machine will stop when the button is released.
NOTE: · The start/stop button cannot be used when the foot
control is connected to the machine. · You can select the desired start-up speed from slow,
medium or high (refer to page 143).
(2) Reverse button · When the following stitch patterns are selected:
Utility Applique Quilt Bridge Decorative
The machine will sew in reverse as long as the reverse button is pressed. Release the button to sew forward. When the machine is stopped and foot control is disconnected, the machine will sew in reverse slowly as long as the reverse button is pressed. Release the button to stop the machine. · When any other stitches are selected: If you press the reverse button when sewing any other patterns, the machine will immediately sew locking stitches and automatically stop.

Press the auto-lock button to sew a locking stitch immediately. The machine will automatically stop.
When the machine is stopped, press the auto-lock button and the LED signal (7) will blink. The machine will immediately sew locking stitches and automatically stop when the machine is started.
· When any other stitches are selected: Press the auto-lock button to sew a locking stitch at the end of current pattern. The machine will automatically stop.
When the machine is stopped, press the auto-lock button and the LED signal (7) will blink. The machine will sew a locking stitch at the end of the current pattern and automatically stop when the machine is started.
The machine will trim the threads automatically after locking the stitch when the auto thread cutting is turned on (refer to page 142).
(4) Needle up/down button
Press this button to bring the needle bar up or down. The machine will stop with the needle in down position. However, you can change the needle stop position in the machine setting mode (refer to page 142).
(5) Presser foot lifter button
The presser foot will go up or down by pressing this button.
You can also use the presser foot lifter and knee lifter to raise and lower the presser foot (refer to pages 18 and 34).
(6) Thread cutter button
After finishing sewing, press this button to trim the threads. The needle bar automatically rises after trimming the threads (refer to page 42). The LED signal (8) blinks when the machine trims threads.
NOTE: · The thread cutter button does not function:
– directly after turning on the power. – when the presser foot is raised with the presser foot
lifter. – after being pressed 3 times in a row.
· Use the thread cutter on the face plate if the thread is #30 or thicker (refer to page 42).

NOTE: There will be particular functions of the reverse button when stitch pattern U2, U3, B2, B13, or B14 is selected. Refer to pages 47, 62-63, 68 and 121 for instructions.

After using auto thread cutting or threading the bobbin holder, you can start sewing without drawing up the bobbin thread.

16

Touch Panel Keys and Jog Dials

CAUTION:
Do not press the touch panel or visual touch screen with hard or sharp objects like pencils or screwdrivers. Use the touch panel stylus included in the standard accessories.

(1) Home key

Press this key to return the top of the utility stitch pattern

(1)

selections.

(2) Stitch reference key (refer to page 19)

(2)

Press this key to show the stitch reference chart.

(3) Open file key (refer to pages 81 and 102)

(3)

Press this key and the open file window will open.

You can open pattern combinations and monograms

saved in the machine’s internal memory or on a USB

(4)

flash drive.

(4) Set mode key (refer to page 138)

Press this key to enter the setting mode. You can

(5)

customize the machine settings to your preference.

The settings for “Machine Settings”, “Sewing Settings”,

(6)

and “Language Setting” are available in this mode.

(5) Lockout key

(7)

Press this key to lockout the machine when threading the

machine, replacing the accessories, etc.

To reduce the risk of injury, all the buttons except the lockout key and presser foot lifter button are deactivated.

To unlock the machine, press this key again.

(9)

(8)

(6) Touch bar
Press on the bar and slide to the right or left to display the next page or previous page.

(7) Page keys
Press the page key to display the next page or previous page. Press and hold the page key to turn the pages continuously.

(8) Stitch length adjusting dial (refer to pages 51, 60, etc.)
Turn this jog dial to alter the stitch length of the selected pattern.
(9) Stitch width adjusting dial (refer to pages 50, 53, 60, 68, 122, etc.)
Turn this jog dial to alter the stitch width or needle drop position of the selected stitch pattern.

17

(2) (1)

(5)
(4) (2)

(6)

(3)

Raising and Lowering the Presser Foot
CAUTION:
Do not turn the handwheel or press the needle up/ down button when the presser foot is in extra lifted position. This may cause damage to the presser foot.
The presser foot lifter button, the presser foot lifter or the knee lifter raises and lowers the presser foot. You can raise the presser foot about 6 mm (1/4) higher than the normal up position by exerting more pressure when lifting the presser foot lifter or knee lifter. This helps you to place layers of thick fabric.
(1) Presser foot lifter button (2) Presser foot lifter (3) Presser foot (4) Up position (5) Extra lifted position (6) Down position
NOTE: The presser foot cannot be lowered with the presser foot lifter if the foot was raised with the presser foot lifter button.

18

Stitch Reference Chart

Press the stitch reference key to show the stitch reference chart window.

You can select stitches directly by pressing stitch patterns in the stitch reference charts.

(1)

(1) Stitch reference key

(2) Page number

NOTE:
· Stitch reference charts will not be displayed if the monogram key or sewing application key is selected.
· When selecting some specific sewing such as twin needle sewing, stitch patterns not suitable for those
sewing in the stitch reference chart are grayed out
and cannot be selected.

(2)

(2) 19

(2) (3)
(1)
(2)

(1) (4)

Winding the Bobbin Removing the Bobbin Press the lockout key. Slide the hook cover release button to the right, and remove the hook cover plate.
(1) Hook cover release button (2) Hook cover plate
Lift out the bobbin from the bobbin holder. (3) Bobbin
NOTE: · Use “J” plastic bobbins (4) for the horizontal hook.
Using other bobbins, such as pre-wound paper bobbins, may cause stitching problems and/or damage to the bobbin holder. · Do not use the easy bobbin or metal bobbins.
Setting the spool of thread Lift up the spool pin. Place the spool of thread on the spool pin. Attach the spool holder (large), and press it firmly against the spool of thread.
(1) Spool holder (large)
Use the spool holder (small) to hold narrow or small spools of thread.
(2) Spool holder (small)

(3)
(3) (3)

(4) (5)
(4)
(1)
(2)

Use the spool holder (special) to hold the specific size of the spool of threads as shown. The sizes of the spools of thread are as follows; The hole diameter of the spool has a range of 3/8 to 7/16 (9.5 mm to 10.5 mm), and the spool length has a range of 2 3/4 to 3 (70 mm to 75 mm).
(3) Spool holder (special) (4) Hole diameter (3/8 to 7/16) (5) Spool length (2 3/4 to 3)
Firmly insert the spool holder (special) into the hole and hold the spool as illustrated.
Extra spool pin Use the extra spool pin when you need to wind a bobbin without unthreading the machine while working on a sewing project (refer to page 21). Insert the extra spool pin into the hole as shown. Place a spool of thread on the extra spool pin and fix the spool with the spool holder.
(1) Extra spool pin (2) Hole for extra spool pin (3) Spool holder
NOTE: The extra spool pin is also used for twin needle sewing.
20

Winding the bobbin

NOTE: Set the speed control slider at the fastest position (refer to page 15).
1. Pull the thread from the spool. Hold the thread with both hands and pass the thread into the guide slot. Draw the thread to the left and forward around the thread guide. Draw the thread to the rear and to the right around and under the guide plate. (1) Guide slot (2) Thread guide (3) Guide plate
2. Firmly pull the thread to the right while holding it with both hands.
Bobbin winding when the extra spool pin is attached If you want to wind the bobbin with the extra spool pin, do not pass the thread into the guide slot. Instead, draw the thread around the thread guide as shown.
(1) Guide slot (2) Thread guide
3. Put the bobbin on the bobbin winder spindle. Be sure that the bobbin snaps into the place. (4) Bobbin (5) Bobbin winder spindle (6) Slit (7) Spring (Projection)
4. Pass the thread to the bobbin. Hold the thread with both hands and wind it around the bobbin clockwise several times.
5. Insert the thread into one of the slits of the flange plate and pull the thread to cut. (8) Flange plate (9) Slit
6. Push the bobbin to the right. The visual touch screen will show the bobbin winding sign.
NOTE: Do not move the bobbin winder spindle while the machine is running.
7. Start the machine. Stop the machine when the bobbin is fully wound and stops spinning. Return the bobbin winder spindle to its original position.
8. Remove the bobbin. Cut the thread with the bobbin thread cutter B. (10) Bobbin thread cutter B
NOTE: For safety purposes, the machine will automatically stop 1.5 minutes after starting bobbin winding.
21

Inserting the Bobbin

1. Press the lockout key.

Place the bobbin in the bobbin holder with the thread

(2)

(3)

running off counterclockwise as shown on the hook

cover plate.

(1) Lockout key (2) End of thread (3) Bobbin holder (4) Hook cover plate

(1)

(4)

(5)

(6)

(7)

(8) Correct

Wrong

2. Hold the bobbin with your fingertip so it does not rotate. Guide the thread into the front notch of the bobbin holder. Pull the thread to the left to pass it under the guide. (5) Front notch (6) Guide
3. Draw the thread to the left to pass it into the guide path marked “1”. Make sure that the thread comes out from the side notch of the bobbin holder. (7) Guide path 1 (8) Side notch
NOTE: If the thread does not come out from the side notch, rethread from step

(8)

(8)

4. (9)

(10)

(4)

4. Continue to draw the thread along the guide path marked “2” and pull the thread to the right through the slit. The thread will be cut to a proper length and held in place. (9) Guide path 2 (10) Slit (Thread cutter)
5. Set the left edge of the hook cover plate into the opening. Push the hook cover plate down to fit in place.
NOTE: · Unless otherwise noted, you can start sewing
without drawing up the bobbin thread. · Refer to page 26 for how to draw up the bobbin
thread.
22

6. 7.

3. 4. 8.

1. (2)

Threading the Machine

CAUTION:
Always make sure to press the lockout key to lockout the machine before threading the machine.
Press the needle up/down button to raise the take-up lever to the highest position. Press the lockout key to lockout the machine. The presser foot will go down and the upper thread tension disks will open.
(1) Lockout key
(1) Pass the thread in order from 1. to 8. 1. Hold the thread with both hands and pass the thread into the guide slot. (2) Guide slot

2. (3)
   (4)
   3. 4.
   (4) (5) (7)
   (6)

2. Be sure that the thread is pulled down under the notch and into the space below the guide slot as shown. (3) Notch
3. Hold the thread with both hands and draw the thread around the corner of the guide. Firmly pull the thread toward you along the right channel until the thread snaps. (4) Corner of the guide (5) Right channel
4. Draw the thread down along the right channel and around the bottom of the thread guide plate. Pull the thread up along the left channel. (5) Right channel (6) Thread guide plate (7) Left channel
23

5. (8)
   6. 7.
   (9)
   (10)

5. While holding the thread at the spool, firmly draw the thread up and to the back of the take-up lever. Draw the thread forward to slip it into the eye of the take-up lever. (8) Eye of the take-up lever
6. Then pull the thread down along the left channel and through the lower thread guide. (9) Lower thread guide
7. Slide the thread from the right of the needle bar thread guide to the left. (10) Needle bar thread guide
8. Thread the needle with the needle threader (refer to the next page).

Example (1)

Guide Sticker for Threading
There is a threading guide sticker in the standard accessories. If you wish, you can attach the sticker on the machine to check the threading procedure.
(1) Threading guide sticker

24

1. (1)

2. (3)

Built-in Needle Threader

NOTE:

· The needle threader can be used with a #11 to #16

needle.

· Thread size 50 to 90 is recommended.

(2)

· Do not use thread size 30 or thicker.

· The needle threader cannot be used with the twin

needle.

1. Press the needle up/down button to raise the needle. Press the lockout key to lock the machine. (1) Needle up/down button (2) Lockout key
2. Pull the thread up to the left, over the needle threader guide while holding the thread near the spool with your hand. (3) Needle threader guide

(4)

NOTE:

Be sure that the thread pass the slit of the needle

threader as shown.

(4) Slit

3. Pull the thread up and slip it between the thread cutter and face plate from behind.
Pull the thread toward you to cut.
4. Pull down the needle threader lever as far as it will go.

5. Slowly release the needle threader lever to its original

position to pass the thread through the needle eye.

NOTE: If the thread loop is formed after releasing the needle threader lever, pull out the thread loop through the needle eye.
25

1. (1) (2)

2. (3)

3. (4)

Drawing Up the Bobbin Thread After using auto thread cutting or threading the bobbin holder, you can start sewing without drawing up the bobbin thread. However, you need to draw up the bobbin thread when sewing gathering stitches, etc. 1. Remove the bobbin. Insert the bobbin into the
bobbin holder again and rethread the bobbin holder according to the instructions on page 22, but leave a 10 cm (4) tail of bobbin thread as shown.
(1) Bobbin thread NOTE: Do not cut the bobbin thread with the thread cutter.
(2) Thread cutter 2. Raise the presser foot. Hold the needle thread lightly
with your left hand. (3) Needle thread
3. Press the needle up/down button twice to lower and raise the needle and pick up the bobbin thread. (4) Needle up/down button
4. Pull both threads 10 cm (4) under and behind the presser foot.

26

(1) (3)
(4)

Replacing Needles
CAUTION:
Always make sure to press the lockout key to lockout the machine before replacing the needle.

Raise the needle by pressing the needle up/down button.

Press the lockout key.

(2)

(1) Needle up/down button

(2) Lockout key

Loosen the needle clamp screw by turning it counterclockwise. Remove the needle from the clamp.
(3) Needle clamp screw

Insert a new needle into the needle clamp with the flat side of the needle to the rear.
(4) Flat side

When inserting the needle into the needle clamp, push it up against the stopper pin and tighten the needle clamp screw firmly with a screwdriver.

To check needle straightness, place the flat side of the needle onto something flat (a needle plate, glass, etc.).
The gap between the needle and the flat surface should be consistent.
(5) Gap

(5)

Never use a blunt needle.

CAUTION:
Be sure to tighten the needle clamp screw firmly with a screwdriver when attaching a needle to the machine, otherwise the needle may break or cause malfunction.

Fabric

Thread

Needle

Lawn

Georgette Cotton #80-100 Blue tip needle

Fine Tricot

Synthetic

Universal needle

Organza #80-100

9/65-11/75

Crepe

Medium

Sheeting Jersey
Broadcloth
Fleece

Cotton #50-80
Synthetic #50-80

Red tip needle Purple tip needle Universal needle #11/75-14/90

Heavy weight

Denim Tweed Coating Quilting

Cotton #40-50
Synthetic #40-50

Red tip needle Purple tip needle Universal needle #14/90-16/100

NOTE: 1 x twin needle, 2 x blue tip needle (#11/75), 1 x red tip needle (#14/90) and 1 x purple tip needle (#14/90) are included in the needle case (Part No. 859856005).

Fabric and Needle Chart
· For general sewing, use a red needle. · Fine threads and needles should be used for sewing
fine fabrics. · In general, use the same thread for both needle and
bobbin. · Use a blue tip needle for sewing fine fabrics, stretch
fabrics, tricot and buttonholes to prevent skipped stitches. · Use a purple tip needle for sewing knits, free quilting and across the hem to prevent skipped stitches. · Use a stabilizer or interfacing for stretch or fine fabrics to prevent seam puckering. · Always test the thread and needle size on a small piece of the same fabric you will use for actual sewing.

27

1. (1)

2. (3)

Replacing the Presser Foot
CAUTION:
· Always make sure to press the lockout key before replacing the presser foot.
· Use the proper foot for the selected pattern. The wrong foot can cause the needle to break.

(2)

1. Raise the needle by pressing the needle up/down

button.

Press the lockout key.

(1) Needle up/down button (2) Lockout key

2. Raise the presser foot lifter. (3) Presser foot lifter

3. (4)

3. Press the black lever on the back of the foot holder. The presser foot will drop off. (4) Lever
CAUTION:
To avoid damaging the lever, do not push it down.

4. Place the presser foot so that the pin on the foot lies

just under the groove of the foot holder.

(7)

Lower the presser foot lifter to lock the foot in place.

(5) Pin

(6)

(6) Groove

(5)

Each foot is marked with an identification letter.

(7) Identification letter

28

1. (1)
   (3)

2. (5) (4) (1)
   1. 2.

Removing and Attaching the Foot Holder Remove the foot holder before using professional grade foot HP, ruler work foot QR, darning foot PD-H, dual feed foot AD or A.S.R. (Accurate Stitch Regulator).
CAUTION:
Always make sure to press the lockout key to lockout the machine before replacing the foot holder. (2)
Removing the foot holder 1. Raise the needle by pressing the needle up/down
button. Press the lockout key and raise the presser foot with the presser foot lifter.
(1) Needle up/down button (2) Lockout key (3) Presser foot lifter
2. Loosen the thumbscrew and remove the foot holder. (4) Thumbscrew (5) Foot holder

(2) (3)

Attaching the foot holder 1. Attach the foot holder to the presser bar from the
rear. Lower the presser foot with the presser foot lifter.
(1) Foot holder (2) Presser bar
2. Tighten the thumbscrew securely with the screwdriver. (3) Thumbscrew

29

Attaching Ruler Work Foot QR
Attach Ruler work foot QR to the presser bar from behind. Tighten the thumbscrew firmly with the screwdriver.

(1) (2)

Attaching Darning Foot PD-H Attach darning foot PD-H or darning foot PD-H (open-toe) to the presser bar by putting the pin on the needle clamp screw.
(1) Pin (2) Needle clamp screw
Tighten the thumbscrew firmly with the screwdriver.

Attaching Professional Grade Foot HP
Attach professional grade foot HP to the presser bar. Lower the presser foot with the presser foot lifter. Tighten the thumbscrew firmly with the screwdriver.

30

1. 2.
(2)

(3) (2)

(1)

Attaching Dual Feed Foot AD or Dual Feed Plus Professional Foot HP2 1. Attach the dual feed holder to the presser bar from
behind. (1) Dual feed holder
2. Tighten the thumbscrew with your fingers. Push the dual feed link to engage it with upper feed drive. (2) Dual feed link (3) Upper feed drive
3. Lower the presser foot lifter. Lower the needle to the lowest position by turning the handwheel.
4. Tighten the thumbscrew securely with the screwdriver.

(2) (1)

Retractable Sewing Light In addition to the twin LED lights, the machine is equipped with a retractable sewing light. Place your finger in the groove and slide the arm towards you. The light will turn on automatically.
(1) Arm (2) Groove Push back the arm to turn the light off and store it.
CAUTION:
Do not hit or exert excessive force on the arm of the retractable sewing light as this may cause damage when it is extended.
31

Replacing the Needle Plate

Use the straight stitch needle plate when using the

dual feed foot, quilt piecing or free motion. Use the professional grade needle plate HP when using the

professional grade foot HP.

CAUTION:

(1)

· Always make sure to press the lockout key to lockout

the machine before replacing the needle plate.

(2)

· Never press the needle plate release lever while

running the machine.

NOTE:

When the straight stitch needle plate or professional

grade needle plate HP is attached to the machine, the

patterns not suitable for the straight stitch needle plate

or the professional grade needle plate HP cannot be

(3)

selected.

1. Press the needle up/down button to raise the needle. Press the lockout key.

Press the presser foot lifter button to raise the

presser foot.

(1) Needle up/down button

(5)

(2) Lockout key

(3) Presser foot lifter button

2. Slide the extension table to the left to remove it. Push down the needle plate release lever and the needle plate will snap off.
(4) Needle plate release lever (5) Needle plate

(4)

3. A warning message will appear that the needle plate

is not secured.

Remove the needle plate to the right. Place the straight stitch needle plate or professional grade needle plate HP on the machine. Set the left edge of the needle plate into the opening.

4. Push down on the mark of the needle plate until it

locks in place.

Make sure the warning message disappears and the

(6)

straight stitch is automatically selected.

Turn the handwheel slowly and make sure that the

needle does not hit the needle plate.

Press the lockout key to unlock the machine. (6) Mark

32

Using the Straight Stitch Needle Plate

(1)

The straight stitch needle plate has three holes where the

needle enters. The straight stitch needle plate is helpful

to hold and support the fabric when the needle pierces

the fabric. Use the straight stitch needle plate for better

results.

(1) Three holes

It is recommended to use straight stitch needle plate to select patterns U1 to U3 when sewing straight stitches.
Refer to page 32 for how to attach the straight stitch needle plate.

NOTE: The patterns not suitable for the straight stitch needle plate are grayed out.

Dropping the Feed Dogs
The feed dogs can be lowered for sewing on buttons, free motion quilting, etc. Shift the drop feed lever toward you to lower the feed dogs.
(1) Drop feed lever (2) Feed dogs

(2)

Shift the drop feed lever away from you to raise the feed

dogs, it will return to the up position when you start the

machine.

(1)

NOTE: If you start the machine with the feed dogs lowered, a message will appear on the visual touch screen.

33

Knee Lifter

The knee lifter is extremely helpful when sewing

patchwork, quilting, etc. since it allows you to handle the

(3)

fabric while your knee controls the presser foot.

Attaching the knee lifter

(2)

Match the ribs on the knee lifter with the notches in the

knee lifter socket and insert the knee lifter.

(1) Knee lifter

(2) Rib

(1)

(3) Knee lifter socket

Adjusting the knee lifter

The angle of the knee lifter can be adjusted to fit the user.

Loosen the setscrew and slide the angle bar in or out to

(4)

adjust the angle of the knee lifter.

Tighten the setscrew to secure the angle bar.

(4) Setscrew (5) Angle bar

Using the knee lifter

(5)

Push the knee lifter with your knee to easily move the

presser foot up and down.

You can control how high the foot rises by the amount of knee pressure you exert.

Using the Cloth Guide

(1)

Remove the extension table and attach the extra wide

table (refer to page 9).

(1)

Attach the cloth guide to the free-arm by pushing the

cloth guide down to snap it in place.

Slide the cloth guide to the desired position.

Place the fabric with its edge against the guide and sew.

(1) Cloth guide

(2) Free-arm

(2)

(3) Guide

(4) Edge

(4) (3)

34

(1) (2) (3) (4) (5)

ORDINARY SEWING MODE

Ordinary Stitch Patterns
In the ordinary sewing mode, there are 5 categories available.
(1) Utility stitches and buttonholes (2) Decorative and quilting stitches (3) Monogramming (4) Tapering (5) Sewing applications Press one of the keys to select the category.
NOTE: In this manual, the pattern number refers to the initial letter for each group or category. For example, pattern #15 in the buttonholes and specialty stitches is referred to as pattern B15.

(1)

(1) Utility stitches and buttonholes

Utility (U)

You can select utility stitches for seaming, overcasting, blind hemming, basting and shell tucking.

Buttonhole (B) There are various styles of buttonholes, button sewing, darning, tacking, fly stitches and eyelets available in this category.
35

(2)
(A) (H) (QS)
(K) (W) (CS)
(3)

(C) (BR) (Q) (BO) (S) (AN)
(SE) (M)

(2) Decorative and quilting stitches

This category consists of the following 17 groups.

· Applique (A)

· Cross-stitch (C)

· Heirloom (H)

(D)

· Quilt (Q) · Quilt Style (QS)

· Satin (S)

(L)

· Bridge (BR)

· Decorative (D)

(LS) · Botanical (BO) · Long (L)

· Animals (AN)

· Life Style (LS)

· Kids (K)

· Seasons (SE)

· Words (W)

· Mirage (M)

· Created Stitch (CS)

(3) Monogramming
You can program lettering as well as a combination of characters and symbol patterns (refer to pages 97-99).

36

(4) Tapering

(4)

You can taper the beginning and end of the decorative

stitch patterns to create tapered corners and points (refer

to pages 90-96).

37

(5) Sewing applications

(5)

You can select the appropriate stitch for a specific sewing

project and fabric type from the designated application in

this category (refer to pages 103-137).

Press one of the key to select the category.

(6) Sewing key (7) Quilt key
(8) Optional foot key

(6)

(7)
(8) 38

(1) (2) (3) (4) (5)
(6) (7) (8)

Function Keys (1) Foot-up key If this option is turned on, the needle stops at the down position and the presser foot will automatically go up when the machine stops. Press this key to turn this option on or off (refer to page 52).
(2) Twin needle key Press this key to set the stitch width for twin needle sewing (refer to pages 82-83).
(3) Dual feed key Press this key for dual feed sewing (refer to pages 43-44).
(4) Floating mode key Press this key for floating mode (refer to page 46).
(5) Startover key If you stop sewing in the middle of a stitch pattern and wish to sew the pattern again from the beginning, press this key before you start sewing. Press this key once to startover from the beginning of the current pattern, or press this key twice to startover from the beginning of the first pattern of the combination (refer to page 87).
(6) Program key Press this key to program a pattern combination. When this key is pressed, the mirror image keys, delete key, preview key, letter size key, save file key and cursor keys will appear (refer to pages 84-89).
(7) Vertical mirror image key Press this key to sew a vertical mirror image of the selected pattern (refer to page 84).
(8) Horizontal mirror image key Press this key to sew a horizontal mirror image of the selected pattern. The key is grayed out if the selected pattern cannot be turned over (refer to page 84).

(9) (9) Initial lock stitch key Press this key to turn on or off the initial lock stitch.
39

(11) (12) (13) (14) (15) (16)
(10)

(10) Cursor keys Press one of the cursor keys to move the cursor up or down.
(11) Letter size key Press this key to select full size (L) or small size (S).
(12) Letter case key Press this key to select upper case or lower case for monograms.
(13) Delete key Press this key to delete a pattern from the pattern combination.
(14) Preview key Press this key to view the stitch image of the entire pattern combination.
(15) Function switch key Press this key to switch the function keys.
(16) Save file key Press this key to save the pattern combination as a file.

(17) (18)

(17) Hiragana/Katakana key Press this key to switch Hiragana or Katakana for monograms.
(18) Horizontal/Vertical orientation key Press this key to switch the horizontal or vertical orientation.

(19) (19) Needle stop position key You can select the needle stop position to be either up or down by pressing the needle stop position key.
40

(1) (2)

Utility Stitches Straight Stitches
Patterns U1 to U5 are straight stitches for seaming. Press the pattern selection key for the desired stitch. Starting to sew Place the fabric next to the seam guide line on the needle plate. Lower the needle to the point where you want to start. Pull the needle thread towards the rear and lower the foot.
NOTE: Pull the needle thread to the left when using satin stitch foot F, open- toe satin stitch foot F2, dual feed foot or automatic buttonhole foot R.
Press the start/stop button or foot control to start sewing. Gently guide the fabric along the seam guide line letting the fabric go naturally.
(1) Start/stop button
Sewing from the Edge of Thick Fabric
The black button on the zigzag foot A locks the foot in the horizontal position. This is helpful when you start sewing at the extreme edge of thick fabrics or for sewing across a hem. Lower the needle into the fabric at the point where you wish to start sewing. Lower the foot while pushing in the black button. The foot is locked in the horizontal position to avoid slipping. After a few stitches, the black button is released automatically.
(2) Black button
Changing Sewing Direction
Stop the machine and press the presser foot lifter button to raise the presser foot. Pivot the fabric around the needle to change the sewing direction as desired. Start sewing in the new direction.
NOTE: If you turn on the foot up option, the presser foot will automatically go up when the machine stops (refer to page 52).

5/8 (3)

Turning a Square Corner To maintain a 5/8 seam allowance after turning a square corner, use the cornering guide on the needle plate. Stop sewing when the front edge of fabric reaches the cornering guide lines. Press the presser foot lifter button and turn the fabric 90 degrees. Start sewing in the new direction.
(3) Cornering guide
41

(1) (4)

(3) (2)

Securing Seams

For fastening the ends of seams, press the reverse button and sew several reverse stitches. The machine sews in reverse as long as you press and hold the reverse button.
(1) Reverse button
Press the reverse button once when sewing the locka-matic stitch (pattern U2) or locking stitch (pattern U3) and the machine will lock the stitches off and stop automatically.
Cutting Threads
To cut the threads after finishing sewing, press the thread cutter button. The needle bar and presser foot will automatically go up after trimming the threads.
(2) Thread cutter button
NOTE: · The thread cutter button does not function when the
LED signal is turned off or the presser foot is raised with the presser foot lifter. · Use the thread cutter on the face plate to cut specialized, #30 or thicker threads if the auto thread cutter does not work well. (3) LED signal
To use the thread cutter on the face plate, remove the fabric and draw it to the back. Pull the threads up and slip them between the thread cutter and face plate from behind. Pull the threads toward you to cut.
(4) Thread cutter

(4) (2)

(3)

(1)

Needle Plate Guides
The seam guides are marked on the needle plate, freearm and hook cover plate. The seam guides for 1/4, 3/8 and 5/8 are also marked on the front of the needle plate.
(1) Seam guides on the front of the needle plate
The numbers on the needle plate indicate the distance from the center needle position in millimeters and inches.
(2) Center needle position
The cornering guides are very useful when turning a square corner (refer to page 41).
(3) Cornering guide
The angle scales on the needle plate are useful for patchwork piecing (refer to page 78).
(4) Angle scales

42

(1)
(3) (2)

Sewing with the Dual Feed Device

(1)

Patterns U1 to U5 and Q1 to Q7 can be sewn with the

dual feed device.

The dual feed device is extremely effective when sewing hard to feed materials such as PVC coated fabric or leather. It also eliminates layer slippage.

Refer to page 31 for how to attach the dual feed foot and to engage the dual feed device.

Press the dual feed key and select the desired pattern.

(1) Dual feed key

NOTE: · The patterns not suitable for dual feed sewing are
grayed out. · The dual feed key will gray out or not be indicated
if you selected a pattern not suitable for dual feed sewing.

NOTE:
Dual feed quilting piecing foot 1/4 OD appears on the visual touch screen when
patterns Q2 or Q3 is selected.
Dual feed quilting piecing foot 1/4 OD is an optional item.

Place the fabric under the foot and lower the needle at the point where you wish to start. Lower the presser foot. Start sewing at medium speed.
When seaming plaid fabrics, match the plaids of the upper and lower layers and pin them together. Remove the pins as you sew.

Dual feed balancing dial
The dual feed balancing dial should be set at “0”, however you may need to adjust the dual feed balance depending on the type of fabric.

Check the feed balance by test sewing on an extra piece of the fabric you intend to use.

(A) : If the lower layer puckers, turn the dual feed

(A)

balancing dial toward “+”.

(B) : If the upper layer puckers, turn the dual feed

balancing dial toward “­”.

(1) Upper layer

(2) Lower layer

(1)

(3) Dual feed balancing dial

(B) NOTE: When dual feed feet are not used, return the dual feed balancing dial to the “0” position.

43

(1)

(2)

(2)

Dual Feed Plus Professional Foot HP2 This foot provides superior visibility and is great for curves and precise topstitching. Holds fabrics firmly in sync with the feed dogs to achieve professional results.
Replace the needle plate with the professional grade needle plate HP when using dual feed plus professional foot HP2. Refer to page 32 for how to attach the professional grade needle plate HP.
(1) Professional grade needle plate HP Refer to page 31 for how to attach dual feed plus professional foot HP2 and to engage the dual feed device. Press the dual feed key and select the desired pattern.
(2) Dual feed key
NOTE: The patterns not suitable for dual feed sewing will not be displayed.

Place the fabric under the foot and lower the needle at the point where you wish to start. Lower the presser foot. Start sewing at medium speed (refer to page 43).
44

Sewing with Professional Grade Foot HP

(1)

Use the professional grade foot HP for straight stitch to

provide professional results.

Replace the needle plate with the professional grade needle plate HP when using the professional grade foot HP. Refer to page 32 for how to attach the professional grade needle plate HP.

(1) Professional grade needle plate HP

Refer to page 30 for how to attach the professional grade foot HP.
Attach the professional grade needle plate HP and professional grade foot HP and select the desired pattern.

NOTE: The patterns not suitable for the professional grade needle plate HP will not be displayed.

Place the fabric under the foot and lower the needle at the point where you wish to start. Lower the presser foot. Start sewing.

45

1. 2. 3.

Floating Mode

(1)

You can decrease layer slippage and wrinkles by lifting

the presser foot slightly in the floating mode.

1. Press the floating mode key. (1) Floating mode key

NOTE: Patterns not suitable for floating mode are grayed out.

2. Press the setting bar to expand the manual setting window.
(2) Setting bar

(2)

3. Press “+” or “­” to adjust the presser foot height. (3) Presser foot hight adjustment key
Press “+” to increase the presser foot height. Press “­” to decrease the presser foot height.

NOTE:

(3)

· When using the floating mode, always adjust the

presser foot height and conduct a test sew on an

extra piece of the fabric before actual sewing.

· Using the dual feed foot is recommended to

decrease layer slippage when the floating mode

does not work.

46

Variety of Straight Stitches U1 Straight stitch in center needle position Use this stitch for seaming, rolled hemming, etc.
U2 Lock-a-matic stitch Use this stitch to secure the beginning and the end of a seam with backstitching. When you reach the end of the seam, press the reverse button once. The machine will sew four reverse stitches, four forward stitches, and then stop sewing automatically.
U3 Locking stitch This unique stitch is used where an invisible locking stitch is needed. The machine will sew several locking stitches at the beginning and continue sewing forward. When you press the reverse button at the end of the seam, the machine will sew several locking stitches in place, then stop sewing automatically.
U4 Straight stitch in left needle position Use this stitch to seam fabrics close to the edge.
U5 Triple stretch stitch This strong, durable stitch is recommended for areas where both elasticity and strength are needed to ensure comfort and durability. Use it to reinforce areas such as crotch and armhole seams. Also use it when constructing items such as backpacks for extra strength.
U6, U7 Stretch stitches These are narrow stretch stitches designed to eliminate puckering on knit fabrics and bias seams, while permitting the seam to be pressed completely open flat. Use U7 for seaming fine fabrics or stretch fabrics.
47

U8 Basting Refer to page 119 for sewing instructions.
Variety of Zigzag Stitches U9, U10 Zigzag stitches Zigzag stitches are used for various sewing needs including overcasting. These stitches can be used on most woven fabrics. A dense zigzag stitch can also be used for applique.
U11 Multiple zigzag stitch This stitch is used for mending tears.
48

Variety of Overcasting Stitches U11 Multiple zigzag stitch This stitch is used to finish a raw edge of synthetics and other stretch fabrics that tend to pucker. Sew along the fabric edge leaving an adequate seam allowance. After sewing, trim off the seam allowance close to the stitches.
U12 Overcasting stitch This stitch can be used to simultaneously seam and overcast edges of fabrics. Use this stitch when you do not need to open seams flat. Place the fabric edge next to the guide of the foot and sew.
U13 Knit stitch This stitch is recommended for sewing such fabrics as synthetic knits and stretch velour as it provides the greatest amount of elasticity and strength. Place the fabric edge next to the guide of the foot and sew. For better results, use zigzag foot A and sew leaving an adequate seam allowance. After sewing, trim the seam allowance close to the stitches.
U14 Double overedge stitch This stitch is excellent for fabrics that tend to fray extensively such as linens and gabardines. Place the fabric edge next to the guide of the foot and sew. Two rows of zigzag stitches are simultaneously sewn over the edge to insure that the fabric will not ravel.
U15 Overlock stitch This stitch finishes the edges of fabric in a way similar to a commercial overlocking machine for a professional look. Place the fabric edge next to the guide of the foot and sew.
49

(1)

(2)

(3) (2)

(+) (-)

(-)

(4.5)

(+)

Manual Stitch Settings You can alter the stitch width, needle drop position of the straight stitches, needle thread tension, presser foot pressure value and stitch length. Turn the stitch width or length adjusting dial, or press the “+” or “­” key to change the setting. Press the default key to recover the original stitch setting.
When you press the setting bar, the manual setting window expands to show more options. You can alter other settings such as needle thread tension and presser foot pressure value, depending on the selected stitch pattern. Press the setting bar again to shrink the manual setting window.
(1) Setting bar (2) Manual setting window (3) Default key
Altering needle drop position (straight stitches) Turn the stitch width adjusting dial clockwise to move the needle drop position to the right. Turn the stitch width adjusting dial counterclockwise to move the needle drop position to the left.
You can also change the setting with the “+” or “­” key. Press the “+” key to move the needle drop position to the right. Press the “­” key to move the needle drop position to the left.

(+) (-)

(-)

(3.0)

(+)

Altering stitch width Turn the stitch width adjusting dial clockwise to increase the stitch width. Turn the stitch width adjusting dial counterclockwise to decrease the stitch width.
You can also change the setting with the “+” or “­” key. Press the “+” key to increase the stitch width. Press the “­” key to decrease the stitch width.
NOTE: The adjustable range for patterns U6-U7 and U9-U11 is 0.0 to 7.0.

50

(+) (-)

Altering stitch length

(+)

Turn the stitch length adjusting dial clockwise to increase

the stitch length.

Turn the stitch length adjusting dial counterclockwise to decrease the stitch length.

(-)

You can also change the setting with the “+” or “­” key.

Press the “+” key to increase the stitch length.

Press the “­” key to decrease the stitch length.

NOTE:

(-)

(+)

(-)

(+)

· The adjustable range for patterns U1-U6 and U9-

U11 is 0.0 to 5.0.

· The adjustable range for pattern U7 is 1.0 to 5.0.

Adjusting Thread Tension This machine is equipped with automatic thread tension control, which optimizes the tension balance for the selected stitch pattern. Balanced thread tension Straight stitch: Both needle and bobbin threads interlock between the layers.
Zigzag stitch: The needle thread appears slightly on the wrong side of the fabric.

However you may need to manually adjust the tension balance depending on the sewing conditions, or you can fine-tune the thread tension to suit your preference.
(1) Press the “+” key if the tension is too loose. (2) Press the “­” key if the tension is too tight.

(1)

(2)

51

Adjusting Foot Pressure Control
The presser foot pressure is automatically optimized for each stitch pattern.
However, you can adjust the foot pressure manually by pressing the “+” key or “­” key to suit your specific sewing needs.

(1)
(2) (3) (4)
(1)

Number of Locking Stitches The machine sews 5 lock stitches at the beginning and 3 lock stitches at the end. However, you can change the number of lock stitches at the beginning and the end with this option. To change the number of lock stitches at the beginning, press the “+” or “­” key in section (3). To change the number of lock stitches at the end, press the “+” or “­” key in section (4).
(1) Lock stitches at the beginning (2) Lock stitches at the end
NOTE: This option is available only for the locking stitch (U3).
Foot Up for Pivoting If this option is turned on, the presser foot will automatically go up when the machine stops. This feature is very useful when turning corners. Press the foot-up key to turn this option on or off.
(1) Foot-up key
NOTE: Height of the foot can be adjusted in the sewing setting mode (refer to page 143).

52

Favorite Stitch Adjustment

You can save customized stitch settings (stitch length,

stitch width, thread tension and presser foot pressure,

depending on the selected stitch patterns) as “Favorite

Stitch Adjustment”. When the favorite stitch adjustment

option is turned ON (refer to page 145), the last-used

customized stitch settings are automatically assigned

(1)

when the stitch pattern is selected.

(1) Favorite Stitch Adjustment

NOTE:
· Favorite stitch option cannot be assigned for created stitch (CS).
· Favorite stitch option cannot be used in monogram
mode.

(2)

(3)

(4) (6)

(5)

Example: To change the preset value of the needle drop position from “4.5” to “5.0”.
Turn the Favorite Stitch Adjustment option ON (refer to page 145).
Select stitch pattern U1. Press the setting bar. The manual setting window expands to show more options. The favorite stitch key appears on the manual setting window.
Change the needle drop position from “4.5” to “5.0” by turning the stitch width adjusting dial or pressing “+” key. Press the favorite stitch key. The dialog box will open. Press the save favorite key to register the favorite stitch settings.
(2) Setting bar (3) Favorite stitch key (4) Save favorite key
The square bracket indicates that the customized preset stitch value is applied to the setting.
To delete favorite stitch settings, press the favorite stitch key and press the delete key.
(5) Square bracket (6) Delete key

53

Other Utility Stitches U16, U17 Blind Hem Refer to page 110-111 for sewing instruction.
U18, U22 Shell Tuck Refer to page 112 for sewing instruction.
U19 Visible hemming Fold and press a single hem. Place the fabric with the right side up. Sew along the fold at the desired depth. Trim the excess on the wrong side.
54

U20 Attaching elastic Mark the elastic into quarters. Match those to the center front, center back and side seams, and pin the elastic to the fabric. Place the elastic under the foot and stitch into place while stretching the elastic evenly.
U21 Box stitching Use this stitch to join heavy weight fabrics. Overlap two raw edges together and use this stitch to join them. Use also for fagoting.
U23 Hemstitch Use this stitch for fagoting or decorative stitch.
U24 Backward stitch U24 is backward stitch. Use the stitch if it is hard to guide the fabric while pressing the reverse button. The machine sews in reverse without pressing the reverse button so that you can guide the fabric with both hands.
55

BUTTONHOLES AND SPECIALTY STITCHES

Variety of Buttonholes B1 Sensor (square) buttonhole This square buttonhole is widely used on medium to heavy weight fabrics. The buttonhole size is automatically determined by placing a button in the foot.
B2 Automatic (square) buttonhole This is also a square buttonhole similar to the sensor square buttonhole, but you can manually set the buttonhole size and the machine memorizes it to sew buttonholes of the same size.
B3 Round end buttonhole This buttonhole is used on fine to medium weight fabrics especially for blouses and children’s clothes.
B4 Fine fabric buttonhole This buttonhole is rounded at both ends and is used on fine, delicate fabrics such as fine silk.
B5 Keyhole buttonhole The keyhole buttonhole is widely used on medium to heavy weight fabrics. It is also suitable for larger and thicker buttons.
B6 Rounded keyhole buttonhole This buttonhole is used for thicker buttons on medium weight fabrics.
B7 Tailored buttonhole This durable buttonhole is used with thick buttons and heavy fabrics.
B8 Stretch buttonhole This buttonhole is suitable for stretch fabrics. It can also be used as a decorative buttonhole.
B9 Knit buttonhole This buttonhole is suitable for knit fabrics. It can also be used as a decorative buttonhole.
B10 Antique buttonhole This buttonhole looks like the heirloom stitch. It has an attractive handmade appearance and makes a nice decorative buttonhole.
B11 Welted buttonhole This is a template pattern for the hand sewn welted (bound) buttonhole.
NOTE: B3-B11 are sensor buttonholes and the sewing procedure is the same as for B1.
56

B1 Sensor (Square) Buttonhole
The size of a buttonhole is automatically set by placing a button in the rear of automatic buttonhole foot R.
The button holder of the foot takes a button size of 1 cm (3/8) to 2.5 cm (1) in diameter. When selecting the buttonholes, the visual touch screen advises you to lower the buttonhole lever.
NOTE: · It is sometimes necessary to change buttonhole
size to match certain heavy or specific fabrics and threads. · Make a test buttonhole on an extra piece of the fabric to check your settings. · The preset width of the buttonhole is suited for ordinary buttons. · Apply an interfacing to stretch or fine fabrics.

1. (1) (2) (3)

Sewing
1. Pull the button holder to the back, and place the button in it. Push it together tightly on the button.
(1) Button holder
NOTE: · Check the length of the test buttonhole, and adjust
the buttonhole length if necessary by turning the adjusting screw on the buttonhole foot. · To increase the buttonhole length, turn the adjusting screw to move the marker toward “L”. · To decrease the buttonhole length, turn the adjusting screw to move the marker toward “S”.
(2) Adjusting screw (3) Marker

2. Press the needle up/down button to raise the needle.

Press the lockout key.

Raise the presser foot and attach automatic

(4)

buttonhole foot R snapping the pin into the groove of the foot holder.

You may lift the presser foot lifter to the extra lifted

position when placing the automatic buttonhole foot

(5)

under the foot holder.

Press the lockout key to unlock the machine.

(4) Groove (5) Pin

57

4. (7)

3. Draw the needle thread to the left through the hole of the foot. Mark the buttonhole position on the fabric and place it under the buttonhole foot. Lower the needle at the starting point by turning the handwheel. (6) Starting point
(6) 4. Lower the presser foot and pull the buttonhole lever down as far as it will go. (7) Buttonhole lever

NOTE:

Make sure there is no gap between the slider and

front stopper, otherwise the buttonhole will be out of

position or there will be a sewing gap.

(8) No gap

(8)

(9) Starting point

(10) Sewing gap

(10)
5.

(10) (9)

(10) (9)

(9) 5. Start sewing while pulling the needle thread lightly to the left. After sewing a few stitches, free the thread and continue sewing.
NOTE: If you start sewing without pulling down the buttonhole lever, the visual touch screen will show a warning and the machine will stop after a few stitches. Pull the buttonhole lever down and start sewing.

58

6. The buttonhole is sewn automatically in the sequence

shown.

When the buttonhole is finished, the machine will

stop automatically with the needle in the up position.

Press the thread cutter button and remove the fabric.

7. After you finish buttonhole sewing, push the

buttonhole lever up as far as it will go.

8. Place a pin just below the bartack at each end to

prevent accidentally cutting the threads.

Cut the opening with the seam ripper.

Use a punch to open a keyhole buttonhole.

NOTE: A punch is not included with this machine.

Double Layer Buttonhole To make a sturdy buttonhole, sew another layer of buttonhole stitches over the previous stitches. After the buttonhole is finished, simply start the machine again. Do not raise the foot or buttonhole lever. Do not reselect the pattern.
NOTE: Turn off “Thread Cut after Auto-Lock” option when you make a double layer buttonhole (refer to page 142).

59

Manual Settings

(1)

You can alter the buttonhole opening width, buttonhole

width and buttonhole stitch density on the manual setting

window.

When you press the setting bar, the manual setting window expands to show more options.

(2)

(1) Setting bar

(3)

(4)

(2) Altering buttonhole opening width
Press the “+” key to make the buttonhole opening wider. Press the “­” key to make the buttonhole opening narrower.

(3) Altering buttonhole width
Turn the stitch width adjusting dial clockwise to increase the buttonhole width. Turn the stitch width adjusting dial counterclockwise to decrease the buttonhole width.
Or press the “+” key to increase the buttonhole width. Press the “­” key to decrease the buttonhole width.

(4) Altering buttonhole stitch density Turn the stitch length adjusting dial clockwise to make the buttonhole stitches less dense. Turn the stitch length adjusting dial counterclockwise to make the buttonhole stitches denser.
Or press the “+” key to make the buttonhole stitches less dense. Press the “­” key to make the buttonhole stitches denser.
NOTE: · The opening width is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 2.6 to 9.0. · The stitch density is adjustable from 0.20 to 1.00.
60

Using the Stabilizer Plate

The stabilizer plate holds and supports the fabric so it is

helpful when sewing buttonholes over the hem of thick

fabrics.

1. Insert the tab of the stabilizer plate into the slot of the buttonhole foot.
(1) Stabilizer plate (2) Slot

(2)

(1)

2. Place the button on the button holder of the foot.

Attach the buttonhole foot to the machine.

Draw the needle thread to the left between the foot and stabilizer plate.

3. Place the fabric between the buttonhole foot and

stabilizer plate. Lower the needle into the starting

point by turning the handwheel.

Lower the foot and buttonhole lever.

Start the machine while pulling the needle thread lightly to the left. After sewing a few stitches, free the
thread and continue sewing.

NOTE: The sewing procedure is exactly the same as that for B1 sensor (square) buttonhole (refer to pages 57-59).

61

B2 Automatic (Square) Buttonhole
Pull the button holder all the way out. Draw the needle thread to the left through the hole of the foot. Mark the buttonhole position on the fabric. Place the fabric under the foot, and lower the needle at the starting point by turning the handwheel. Lower the foot and start sewing while pulling the needle thread lightly to the left. After sewing a few stitches, free the thread and continue sewing.
NOTE: · You do not need to pull down the buttonhole lever. · If you wish to sew a buttonhole longer than the size
permitted by automatic buttonhole foot R, use satin stitch foot F.
NOTE: · The opening width is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 2.6 to 9.0. · The stitch density is adjustable from 0.20 to 1.00.

1. Sew the left side up to the required buttonhole length

and stop the machine. Then press the reverse button.

(1) Reverse button

(1)
2.
(1)

2. Start sewing again, and the machine sews back with a straight stitch. Stop the machine when you reach the starting point. Then press the reverse button. (1) Reverse button
62

3. (1)

3. Start sewing again, and the machine sews the front bartack and right side of the buttonhole. Stop the machine when you reach the ending point. Then press the reverse button. (1) Reverse button
4. Start sewing again, and machine sews the back bartack and locking stitches then stops automatically with the needle in the up position. When the buttonhole is finished, a message will appear. To make the next buttonhole, position the fabric and start sewing again. The message disappears and the machine sews another buttonhole identical to the first one then stops automatically.

To sew another buttonhole in a different size, press the X key on the dialog box. NOTE: · To cut the buttonhole opening, refer to the instructions on page 59. · The memorized length will be cancelled if the presser foot is raised or the startover key (refer to page 87) is pressed before buttonhole is completed.
63

Other Buttonholes B3, B4 Round end and fine fabric buttonholes The sewing procedure is the same as that of B1 sensor (square) buttonhole (refer to pages 57-59).
NOTE: · The opening width is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 2.6 to 9.0. · The stitch density is adjustable from 0.20 to 1.00.
B5-B7 Keyhole buttonholes The sewing procedure is the same as B1 sensor (square) buttonhole (refer to pages 57-59). Use a punch to open the keyhole buttonhole. (1)
NOTE: · A punch is not included with this machine. · The opening width (1) is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 5.6 to 9.0. · The stitch density is adjustable from 0.20 to 1.00.
B8, B10 Stretch and Antique buttonholes The sewing procedure is the same as B1 sensor (square) buttonhole (refer to pages 57-59). The sewing steps are as shown.
NOTE: · The opening width is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 2.6 to 9.0. · The stitch density is adjustable from 0.50 to 1.00 (B8),
and from 0.50 to 2.50 (B10).
B9 Knit buttonhole The sewing procedure is the same as B1 sensor (square) buttonhole (refer to pages 57-59).
NOTE: · The opening width is adjustable from 0.2 to 2.0. · The buttonhole width is adjustable from 2.6 to 9.0. · The stitch density is adjustable from 0.70 to 1.20.
64

(2)

(1)
(2)
2.
(1)
3.
(3)
4.
(1)
5.
(3)
6.

B11 Welted Buttonhole (Bound Buttonhole) A welted buttonhole is made by stitching a strip or patch of fabric to the buttonhole. Welted buttonholes are particularly suitable for tailored garments, but are not recommended for sheer or delicate fabrics where the patch might show through or add bulk.
1. Baste a patch to the garment fabric with the right sides together. (1) Wrong side of patch (2) Right side of garment fabric

(3)

2. Select pattern B11.

Sew the welted buttonhole on both fabrics together. Cut the buttonhole opening as illustrated then pull the

patch out through the slit to the other side.

(1) Wrong side of patch

(2) Right side of garment fabric

(3) Right side of patch

(4)

3. Pull out the patch until the right side of the patch is

showing. Use an iron to press both corner ends until

they are squared off.

(3) Right side of patch

(4) Wrong side of garment fabric

(3)

4. Fold back each side of the patch to form buttonhole

lips.

(1) Wrong side of patch (3) Right side of patch

(4)

5. Press both folds with an iron.

(3) Right side of patch (4) Wrong side of garment fabric

(2)

6. Baste both edges of the seam with a needle and

thread by hand.

(2) Right side of garment fabric

65

7. 8.
(1)

(5) (4)
(4) (2)

(3)

(4)

(6)
10.
(7)
(7)
11.
(6)

(7)

(6)

(7)

7. Fold over the length of the garment fabric, sew back and forth beside the original seam to secure flaps of the patch. (4) Wrong side of garment fabric (5) Sew back and forth
8. Fold over the end of fabric and sew back and forth three times over the triangular end. (1) Wrong side of patch (2) Right side of garment fabric (4) Wrong side of garment fabric
9. The patch should be cut 1 cm to 1.5 cm (3/8 – 5/8) away from the hole. The corners should be cut rounded off as shown. (3) Right side of patch (4) Wrong side of garment fabric
10. Place the facing on the wrong side of the garment fabric. Mark the 4 corners with pins as shown. (6) Facing (7) Garment fabric
11. Turn all the layers over and cut the buttonhole opening on the facing in the same way as step 2. Four marker pins show you the corner points on the facing. Fold back each flap between the facing and patch. (6) Facing (7) Garment fabric
12. Stitch around the opening with a needle and thread as shown. (6) Facing (7) Garment fabric
13. The welted buttonhole is complete. (7) Garment fabric

66

(2)

2. 3.

Corded Buttonhole To sew a corded buttonhole, follow the same procedure as for B1 sensor (square) buttonhole.
Select pattern B1. 1. Place the button on the button holder on the
buttonhole foot. Hook a filler cord on the spur on the front of the foot. Bring the ends of cord toward the back and under the foot. Bring up the ends of the cord and insert both ends between the ribs and metal plate.
(1) Spur (2) Metal plate Set the stabilizer plate as necessary and attach the buttonhole foot. (1)
2. Lower the needle into the fabric where the buttonhole will start. Lower the foot and buttonhole lever. Pull the needle thread lightly to the left. Start the machine to sew the buttonhole over the cord. The machine stops automatically when finished. Remove the fabric from the machine and cut the sewing threads only.
3. Cut the filler cord at both ends as close to the buttonhole as possible.
NOTE: · Do not adjust the opening width wider than 0.8. · Set the stitch width in accordance with the thickness
of the cord used. · To cut the buttonhole opening, refer to the
instructions on page 59.
Specialty Stitches B12 Button Sewing Refer to page 120 for sewing instructions.

67

(1)

B13 Darning
1. Attach automatic buttonhole foot R and pull the button holder all the way out.
Place the fabric under the foot, and lower the needle at the starting point. Then lower the foot.
(1) Button holder (2) Starting point

(2)
2.
(3)
0.9 cm
3.

2. Start the machine and continue sewing until the machine stops automatically. When finished sewing, a confirmation message will appear.
NOTE: The machine will sew the darning at maximum 2 cm (3/4) length and fixed 0.9 cm (3/8) width when sewing until it stops automatically.
(3) 2 cm (3/4)
3. Sew another layer of darning over the first layer, at a right angle to it.

To sew shorter darning

(4)

Sew the first line to the desired length and stop the

machine.

Press the reverse button and start the machine again.

The machine will sew the rest of the darning and stop

(5)

automatically.

(4) Reverse button

(5) Required length

To sew the same size darning

When finished sewing, a confirmation message will appear.
Simply start the machine to sew another layer of darning stitches in the same size.
To sew the next layer of darning stitches in a different
size, press the X key.

To adjust the evenness of darning stitches
You can correct unevenness of darning stitches by turning the stitch width adjusting dial or pressing the “­” or “+” key of the adjusting window. If the left corner is lower than the right side, turn the stitch width adjusting dial counterclockwise or press the “­” key to correct it. If the right corner is lower than the left side, turn the stitch width adjusting dial clockwise or press the “+” key to correct it.
NOTE: The memorized length will be cancelled if the presser foot is raised or the startover key (refer to page 87) is pressed before darning is completed.
68

B14 Tacking Refer to page 121 for sewing instructions.

B15 Fly Stitch
The fly stitch is a triangle tacking stitch for use on a zipper fly bottom and on the side pockets of pants.
Attach the satin stitch foot F.

To sew:

(1)

Place the garment under the foot and lower the needle at

the starting point.

Sew the stitch until the machine stops automatically.

(1) Starting point

B16-B18 Eyelets Refer to page 122 for sewing instructions.

69

(1)
(3) (4) (5) (6) (7) (8)
(2) (3)

DECORATIVE STITCHES
Decorative Stitches The patterns in this section are classified into 17 groups. These patterns are programmable and you can make a pattern combination. Press the decorative and quilting stitches key and the decorative stitch selection window will open.
(1) Decorative and quilting stitches key
NOTE: The decorative stitch selection window is composed of multiple pages. Press page keys to switch the decorative stitch selection window.
(2) Page keys
(3) Applique (A): 2 pages Stitches in this group are for applique (refer to pages 132-133).

(4)

(4) Cross-stitch (C): 2 pages

This group provides cross-stitches for craft sewing and home décor.

70

(5) Heirloom (H): 3 pages

(5)

This group provides heirloom stitches for craft sewing

and home décor.

(6)

(6) Quilt (Q): 9 pages

Stitches in this group are for patchwork and quilting (refer to pages 78-79, 125-135).

71

(6) Quilting stitches (Q) (continued from previous

(6)

page)

(7)

(7) Quilt Style (QS): 2 pages

There are stitch patterns created from quilt blocks in this group.

72

(8) Satin (S): 3 pages

(8)

The stitches in this group can be elongated up to 5 times

their original length while the stitch density remains the

same (refer to page 79).

(9) (11) (13) (9)

(10) (12) (14) (10)

(9) Bridge (BR): 1 page Bridge stitches are used for inserting straight stitches after a stitch pattern. The number beside the stitch image on the straight stitch key indicates the stitch count of a programmable unit. Patterns BR5, BR6 and BR8 will inherit the needle drop position and stitch length of the previous pattern in the programmed pattern combination (refer to page 85).
(10) Decorative (D): 6 pages 50 attractive patterns are available in this group. Patterns in this group are ideal for decorating.

73

(10) Decorative stitches (D) (continued from

(10)

previous page)

(11)

(11) Botanical (BO): 3 pages

There are patterns of trees, grass and flowers in this group.

74

(12) Long (L): 2 pages

(12)

Patterns in this group are ideal for decorating garments

and for adding border trims.

(13)

(13) Animals (AN): 1 page

There are patterns of animals in this group.

(14)

(14) Life Style (LS): 3 pages

There are patterns related to lifestyle in this group.

75

(15) (17) (19)
(15)

(16) (18)
(15) Kids (K): 3 pages There are patterns for kids in this group.

(16)

(16) Seasons (SE): 2 pages

There are patterns related to seasons in this group.

76

(17) Words (W): 1 page

(17)

There are word patterns in this group.

(18)

(18) Mirage (M): 1 page

This group provides satin patterns without connecting

straight stitches (refer to page 80).

(19)

(19) Created Stitch (CS): 1 to 5 pages

In this section, you can select original stitch patterns created with StitchComposer.

Refer to page 81 for how to transfer created stitch patterns from a PC to the machine.

77

(2)

Quilting

Using the Quilting Guide Bar

(1)

The quilting guide bar is helpful when sewing parallel, evenly spaced rows of stitches.

Insert the quilting guide bar into the hole in the back of the foot holder. Slide the quilting guide bar and set it to
the desired spacing.

(1) Quilting guide bar (2) Hole

Sew rows of stitches while tracing the previous row of

(2)

stitches with the quilting guide bar.

(1)

(1)

(3)

(4)

(1)

(2)

(2)

(1)

(1)

Q1-Q3 Patchwork Piecing
Patterns Q1 to Q3 are special stitches for seaming patchwork pieces.
Patterns Q2 and Q3 are for patchwork piecing with 1/4 and 7 mm seam allowances respectively. Use 1/4 seam foot O. Place the patchwork pieces with the right sides together. Sew while guiding the edge of fabric along the guide.
(1) Guide (2) Right side of the fabric (2)
You can sew a 1/4 allowance from the guide line with 1/4 seam foot O (without guide) as shown. Align the guide line with the 1/4 guide of the foot and (5) sew.
(3) Guide line (4) 1/4 guide
To sew 1/4 seam allowance from the right fabric edge, (6) align the right edge of the foot and the edge of the fabric
and sew.
(5) Right fabric edge (6) Right edge of the foot

Angle Scales on the Needle Plate
You can easily seam patchwork pieces at the desired angle without marking, by using the angle scales on the needle plate. The angle scales are marked at 45, 60, 90 and 120 degrees. Use the broken lines when piecing the patchwork pieces with 1/4 seam foot O as illustrated.
(1) Broken line

NOTE:

Use the solid lines when piecing the patchwork pieces

with zigzag foot A. Align the edge of the fabric to the

(3)

1/4 seam guide line.

(2) Solid line

(3) 1/4 seam guide line

78

(2) (1)

Circular Sewing

The circular pivot pin is inserted into free arm and provides a pivot point to sew perfect curves or circles for doilies or large scallops.
Select a desired decorative stitch. Fold fabric into quarters to determine center. Pierce center of fabric with pivot pin. Insert pivot pin into hole on the free arm. Lower presser foot and sew. Smooth the fabric out evenly from the center to the front of the foot by hand.
(1) Circular pivot pin (2) Holes for circular pivot pin
NOTE: Light to medium weight fabrics will need a stabilizer to sew the circle/curve correctly.

Q76-Q79 Hand-look Quilt Stitches
Patterns Q76 to Q79 are special stitches for quilting which look like hand sewn stitches.
Use a transparent nylon thread for the needle and ordinary sewing thread for the bobbin. The bobbin thread is pulled up on the right side of the fabric and the stitches look as if they were sewn by hand.

(1) X1 X2 X3 X4 X5

Satin Stitches Elongation Ratio
Patterns S1 to S24 are decorative satin stitches for which the pattern length can be elongated without changing the (4) stitch density. (2) Press the setting bar to expand the manual setting (3) window.
(1) Setting bar
Press the “+” key to elongate the stitch pattern. (2) “+” key
To reduce the elongation ratio, press the “­” key. (3) “­” key
The pattern can be elongated up to 5 times the original length. The elongation ratio is indicated in the box.
(4) Elongation ratio
You can also alter stitch density and stitch width.

79

A
(1)
B

(4) (7) (8)
(3)

Mirage Stitches
Sew Mirage stitch and open the fabric to make patterns without connecting straight stitches.

NOTE: (5) Use a medium fabric (such as sheeting, broadcloth)
for Mirage stitch patterns. Using fine fabrics may cause wrinkles when opened.
(6) There are two ways to sew the Mirage stitch patterns (sewing on one or two pieces of fabric).

A: Sewing on one piece of fabric

Fold the fabric with the right sides together. Place a sheet of stabilizer under the fabric.

(1) Right side of the fabric (2) Sheet of stabilizer

Attach satin stitch foot F to the machine.
Sew the Mirage patterns with the marker on the presser foot along the fabric edge as shown.
Sew the connecting straight stitches on the right side of the fabric edge (on the sheet of stabilizer) as shown.

(3) Marker

(2)

In the Mirage stitch, you can adjust the stitch length of the decorative stitch part and connecting straight stitch

part separately.

Press the setting bar to expand the manual setting

window.

(4) Setting bar

Adjust decorative stitch length adjustment key or connecting straight stitch adjustment key.
(5) Decorative stitch length adjustment key (6) Connecting straight stitch adjustment key (7) Decorative stitch
(8) Connecting straight stitch

(2) (1)
(9)

B: Sewing on two pieces of fabrics
Sew the fabric this way when you want to use two different fabrics on the right and left. Place two pieces of fabric with the right sides together. Place the sheet of stabilizer under the fabric.
(1) Right side of the fabric (2) Sheet of stabilizer
Sew the fabric while keeping a constant seam allowance. (9) Seam allowance
Open the fabric flat to hide the connecting straight stitches.

A

B

80

Created Stitches Original stitch patterns created with StitchComposer are saved in this group. Insert the USB flash drive containing the original stitch patterns and press the open file key.
(1) Open file key
(1)

Select the USB key and the folder list will appear. Select the desired folder to open and the file list will
appear.

(2)

Select the desired file to save the original stitch pattern.

Saved stitch pattern will appear as the pattern selection

key.

You can select, program and sew these patterns the same way as with the built- in stitch patterns.

(2) USB key

NOTE:
· This model supports FAT16 and FAT32 formats only.
If the USB flash drive is not read, check its format (refer to pages 152-153).
· Do not use a USB card reader and USB hub.

To delete a pattern, press the delete key and select the

(3)

pattern to delete.

A confirmation message will appear.

Press the OK key to delete the pattern.

(3) Delete key

NOTE: · Up to 60 patterns can be saved in this group. · Twin needle sewing is not available for the created
stitches.

81

Twin Needle Sewing

(1)

Some of the utility stitches and decorative stitches can

be sewn with a twin needle.

Press the twin needle key and select the desired pattern.

Patterns not suitable for twin needle sewing cannot be selected (pattern selection keys are grayed out).

Buttonholes, specialty stitches, monogram and tapering cannot be selected.

(1) Twin needle key

NOTE: · When you sew patterns with the twin needle, test the
stitches first before you sew on the garment. · Use zigzag foot A or satin stitch foot F for twin
needle sewing. · Use the threads #60 or finer. · When changing the sewing direction, raise the
needle and presser foot then turn the fabric (foot up for pivoting option is not available when the twin needle is selected). · Use the thread cutter on the face plate when cutting threads.

Replace the needle with the twin needle supplied with the standard accessories (refer to page 27).
CAUTION:
· Press the lockout key before changing the needle. · Do not use twin needles other than the ones
included in the standard accessories, otherwise the needle may hit the needle plate, foot or hook and break.
(2) Lockout key (2)

82

4. 2.

A

B (3)

(1)

Insert the extra spool pin into the hole under the top cover. Place a spool of thread on the extra spool pin and the spool stand (refer to page 20).
(3) Extra spool pin
Draw both threads from the spools and pass them through the threading points from 1. to 4. Slip the thread A through the lower thread guide 5., then pass through points 6. and 7. as illustrated. Thread the thread B through the front hole of lower thread guide 5., then pass it through the needle hole 8. Make sure that the two strands of thread from the spools do not get tangled. * A: Thread from spool pin, B: Thread from extra spool
pin.
NOTE: · Threading from points 1. to 4. is the same as for a
single needle (refer to pages 23-24). · The needle threader cannot be used with the twin
needle.
After twin needle sewing is finished, press the twin needle key and the warning message will appear.
(1) Twin needle key Replace the twin needle with a single needle and press the OK key.

83

(1) (2) (3)

(6)

(5)

(4)

PROGRAMMING A PATTERN COMBINATION

The patterns in the decorative stitch category and monograms can be programmed to make a pattern combination. You can program up to 100 patterns in each combination by pressing the program key. The images of programmed patterns are shown on the left side of the visual touch screen.
(1) Program key
Mirror Image of Patterns To sew or program the pattern as a mirror image, press the vertical mirror image key or horizontal mirror image key. Select the desired patterns to create the mirror image. Press the vertical or horizontal mirror image key again to cancel the mirror image function.
(2) Vertical mirror image key (3) Horizontal mirror image key
NOTE: · Horizontal mirror image is available only for specific
patterns. For pattern identification, these patterns are colored in blue on the reference chart inside the top cover.

· The vertical or horizontal mirror image key will gray out when the selected pattern is not suitable for the mirror image.
To view the entire pattern combination, press the cursor keys to scroll over the pattern combination or press the preview key to show the entire pattern combination at a glance. Press the function switch key to show the preview key.
(4) Cursor keys (5) Preview key (6) Function switch key

NOTE: Presser foot pressure cannot be adjusted to the stitch patterns of a pattern combination individually. If you attempt to do so, only the last pattern’s presser foot pressure settings are applied to all the programmed patterns.
84

Bridge Stitches

Bridge stitches are used for inserting straight stitches after a stitch pattern.

The number beside the stitch image on the straight stitch key indicates the stitch count of a programmable unit.

If you want more space between French knots (D5), for example, insert pattern BR5 after pattern D5.

Two counts of straight stitches are added to pattern D5.

D5

BR5

NOTE:

Patterns BR5, BR6 and BR8 will inherit the stitch

length and needle drop position of the previous

pattern in the pattern combination.

85

(2) (1)

Editing a Pattern Combination
The programmed pattern (pattern combination) can be edited in the programming mode. You can insert, delete or flip the stitch pattern by selecting the stitch with the cursor. You can also adjust the stitch width and stitch length.
Deleting a Pattern
The pattern before the cursor or shown in blue is deleted by pressing the delete key.
(1) Cursor (2) Delete key

(4) (3)
(5)

To delete a pattern in the middle of a combination, press the cursor keys to select the pattern you wish to delete. The stitch image of the selected pattern turns blue. Press the delete key to delete the selected pattern.
(3) Cursor keys (4) Selected pattern
Inserting a Pattern Press the cursor keys to select the pattern next to where you wish to insert a pattern. Enter the desired pattern to insert it before the selected pattern.
(5) Inserted pattern

86

(1) (2)
(2)
(3) (4)

Startover Key This is a 2-way function key to start sewing a pattern combination over from the beginning. When you stop sewing a pattern combination, the startover key is activated.
Current pattern startover If you wish to start sewing from the beginning of the current pattern, press the startover key once and start the machine. The key will change and show a triangle and double bar that means the machine will start over from the current pattern of the combination.
(1) Startover key (current pattern of the combination) (2) Current pattern
NOTE: When you stop sewing a pattern combination during the first pattern and press the startover key, the number of the bar above the triangle will not change because the pattern will be sewn from the first pattern.
First pattern startover The key shows a triangle and single bar that means the machine will start over from the first pattern. If you wish to start sewing from the beginning of the first pattern of the combination, press the startover key twice and start the machine.
(3) Startover key (first pattern of the combination) (4) First pattern
NOTE: If auto thread cutting is done, the machine will startover from the first pattern.

87

(1)

(2)

(3) (4)

Checking Pattern Combination Length You can check the total length of the pattern combination by pressing on the pattern combination length key indicated in the preview window. Press the function switch key. Press the preview key and the preview window will open.
(1) Function switch key (2) Preview key (3) Pattern combination length key
The readout of the total length is a theoretical value and the actual length may vary depending on sewing conditions.
For example, select pattern SE5 three times, and sew a pattern combination. If the actual length differs considerably from the readout, measure the actual length and enter the nearest value by pressing the “+” or “­” key. In this case, the theoretical value is 48 mm. However, if the actual length is 40 mm, enter 40 mm by pressing the “­” key. Press the OK to register it.
(4) Actual length

The readout is adjusted automatically when calculating the length of other pattern combinations. The message “Displays the length of the corrected pattern.” appears to indicate that the displayed value is adjusted already.
88

For example select patterns LS4, LS6 and SE5. The theoretical value is 54 mm. However, the read out is calculated according to the measured actual length. In this case, the adjusted value is 45 mm. Press the default key to clear the entered length.
(5) Default key (5)
89

Tapering

You can taper the beginning and end of the decorative

stitch patterns to create tapered corners and points.

Press the tapering key to enter the tapering mode.

(1)

(2)

(1) Tapering key

Press the stitch reference key to show the stitch

reference chart for tapering (refer to page 19).

(2) Stitch reference key

NOTE: · The tapering length varies depending on the stitch
pattern and its tapering shape. Make a test stitch on an extra piece of the fabric to check the tapering length. · If you stop the machine while sewing and change the stitch width, needle drop position or stitch length, the machine will start tapered sewing from the beginning.

Tapered Stitch Sample 1
Example: To sew tapered stitch pattern #9
Select stitch pattern #9. Start the machine. The machine sews the start tapering pattern and pattern body. Sew to the required length, then press the auto-lock button. The machine sews the end tapering pattern and stops.
(1) Auto-lock button (2) Required length (3) Start tapering pattern (4) End tapering pattern

NOTE:

When you press the reverse button while sewing, the

(3)

machine will sew several locking stitches in place,

then stop sewing automatically. The tapering pattern

is not completed.

(1)

(2)

(4)

To sew the same sized tapered pattern

When finished sewing, a confirmation message will

(5)

appear. The number shown indicates the number of the

body patterns.

(5) Number of the body patterns

Press OK and simply start the machine to sew another tapered pattern of the same size.

To sew the same tapered pattern in a different size, press the X key.

90

(1)

(2)

(1)

(3)

(4)

(5)

(6)

Auto-lock Stitch Function
The machine sews auto-lock stitch at the beginning and end of the sewing with the default settings.
However, you can turn on or off the auto-lock stitches by pressing the corresponding auto-lock keys on the visual touch screen.
(1) Initial lock stitch key (2) End lock stitch key (3) Initial lock stitch (4) End lock stitch (5) Lock stitch key (ON) (6) Lock stitch key (OFF)

(5)

(6)

Flipping a Tapered Pattern 1
Press the static flip key to flip a tapered pattern vertically without flipping its start and end tapering degree angle.
(1) Static flip key

91

Adjustment of Tapered Stitches You can adjust the shape of the tapered stitch pattern. Press the tapering adjustment key. The tapering adjustment window will open.
(1) Tapering adjustment key
(1)

Tapering shape

(6)

(4)

Select the shape of the tapering for the beginning and

the end of the stitch patterns by pressing the tapering

(2)

shape keys.

The keys on the top are for start tapering pattern.

(7)

The keys on the bottom are for end tapering pattern.

(2) Tapering shape keys (for start tapering pattern)

(3) Tapering shape keys (for end tapering pattern)

(8)

(4) Start tapering pattern

(5) End tapering pattern

(3)

The numbers in the tapering shape keys indicate the

(5)

degree of tapering. You can apply the tapering alignment

from left, center, right or off. The start and end of the

stitch patterns can be aligned separately.

The shape of the selected tapering pattern will be displayed on the left side of each column.
The upper column shows the start tapering pattern. The middle column shows the pattern body. The lower column shows the end tapering pattern.
(6) Start tapering pattern (7) Pattern body (8) End tapering pattern

92

Pattern body length

The keys on the middle are for pattern body length. The machine sews the pattern body as long as the autolock key is pressed when the free length key is turned on. However, you can set the number of the pattern body to be sewn by pressing the pattern length key.

(1) Keys on the middle

(4)

(2) Pattern body

(3)

(3) Free length key

(1)

(2) (4) Pattern length key

(5) Number of the body patterns

(5)

Press the pattern length key.

Press the “+” or “­” key to set the number to repeat the pattern body.

(4) Pattern length key

(4)

(6) “+” key

(7) “­” key

(6) (7)

(10) (8)

(9) You can also set the number to repeat the pattern body by pressing the numeric pad key. Press the numeric pad key and the numeric keypad window will open. Enter the desired pattern length and press the OK key. (8) Numeric pad key (9) OK key
After the shape of the tapered stitch pattern is selected, press the OK key to apply the tapered stitch pattern.
(10) OK key

93

Flipping a Tapered Pattern 2 Press the mirror image key to flip a tapered pattern vertically.
(1) Mirror image key
(1)
Saving tapered stitches The customized tapered patterns can be saved as a file in the machine’s internal memory or a USB flash drive. Press the save file key after customizing a tapered stitch. The tapered stitch file is saved as a *.JCS file. To save or open the file refer to pages 100-102.
(1) Save file key
(1)
94

2. 3.

Tapered Stitch Sample 2 Example: To create a corner frame with tapered stitch pattern #32
1. Select stitch pattern #32. 2. Press the end lock stitch key to turn off the end lock
stitch. (1) End lock stitch key
3. Press the tapering adjustment key. (2) Tapering adjustment key

4. (3) (5) (7) (6)

(4)

(8)

(1) (2)
4. Press the tapering shape key (for start tapering pattern). Press the tapering shape key (for end tapering pattern). Press the pattern length key. Press the “+” key 4 times or press the numeric pad key and enter “5” (refer to page 93). Press the OK key. (3) Tapering shape key (for start tapering pattern) (4) Tapering shape key (for end tapering pattern) (5) Pattern length key (6) Numeric pad key (7) OK key
5. Press the foot-up key. You can check the number of body patterns on the screen. (8) Foot-up key (9) Number of the body pattern
6. Lower the needle into the fabric at the point where you want to start sewing. Start sewing. Sew until the machine stops. The machine stops and the presser foot rises automatically.

(9) 95

7. (10)

7. Pivot the fabric 90 degrees.
Press the presser foot lifter button to lower the presser foot.
Press the initial and end lock stitch keys.
Be sure that the initial lock stitch key is turned off, and the end lock stitch key is turned on.
Start sewing in the new direction. (10) Presser foot lifter button (11) Initial lock stitch key (1) End lock stitch key

(11)

(1)

8. The machine automatically stops at the end of the

corner with the lock stitch.

96

(1)
(2) (3) (4) (5) (6) (7) (8) (9)
(11) (12) (13) (14)
(15)
(10)
(16) (17)

MONOGRAMMING
You can program letters and symbol designs for monogramming. Press the Monogram key and the font selection window will open.
(1) Monogram key
You can select one of 8 fonts. Select the desired font by pressing the corresponding key.
(2) Block key (3) Script key (4) Broadway key (5) Block (9 mm) key (6) Cyrillic key (7) Mincho (9 mm) key (8) Marumoji (9 mm) key (9) Symbol key The monogram mode window will open.
NOTE: The heights of Block (9 mm), Mincho (9 mm) and Marumoji (9 mm) are approximately 9 mm.
Function Keys (10) Cursor keys Press the cursor keys to move the cursor up or down.
(11) Letter size key Press this key to select the full size (L) or small size (S). (12) Letter case key Press this key to select upper case or lower case.
(13) Delete key Press this key to delete selected characters.
(14) Preview key Press this key to view the entire monogram.
(15) Save file key Press this key to save the monogram as a data file. (16) Hiragana/Katakana key Press this key to switch Hiragana or Katakana for monograms.
(17) Horizontal/Vertical orientation key Press this key to switch the horizontal or vertical orientation.
NOTE: Numbers, symbols and European letters are available on pages 2/5 through 5/5. * These keys are displayed only when Mincho (9 mm)
or Marumoji (9 mm) is selected.
97

(2) (3)
(1)

Manual Thread Tension

(1)

This machine is equipped with automatic thread tension

control. However, you may need to manually adjust the

(4)

tension balance depending on the sewing conditions.

To adjust the thread tension, press the setting bar to

show the option.

(1) Setting bar

Individual Thread Tension Adjustment
To apply the thread tension adjustment to each letter individually, select the letter by moving the cursor with cursor keys.
(2) Cursor (3) Cursor keys

Press “+” or “­” key to adjust the thread tension of the selected letter. The adjusted thread tension is applied to the selected letter.
(4) Thread tension adjustment key

Unified Thread Tension Adjustment
To apply the thread tension adjustment to all letters together, you do not need to select the letters.
Press the unified thread tension key. (5) Unified thread tension key
Press “+” or “­” key to adjust the thread tension. The adjusted thread tension is applied to all entered letters.
When unified thread tension control is applied, the unified thread tension key turns to light blue. Press the unified thread tension key again to deactivate the unified thread tension adjustment.

NOTE:

Unified thread tension adjustment cannot be applied

(5)

to Symbol characters or decorative stitches.

(1) (2) (3) (4)
2/3

Spacing To enter a space in monogramming, press one of the three space keys on the lower right corner of the monogram selection.
(1) Space keys (2) Small-size space (3) Medium-size space (4) Large-size space
Reducing the Size of Letters To reduce the height of a character to approximately 2/3 of full size (L), select the character and press the letter size key.
(1) Letter size key

98

(1) (2)

Programming a Monogram Simply enter the characters by pressing the corresponding keys to program a monogram.
NOTE: · Use a blue tip needle for sewing a monogram. · Apply a sheet of stabilizer to fine fabrics or stretch
fabrics. · Test sew to check the sewing results.
Example 1: “Quilt” in Block font Press the monogram key and select Block font. Enter “Q”.
(1) Monogram key
Press the letter case key to select lower case. (2) Letter case key
Enter “u”, “i”, “l” and “t”.
Start sewing. Sew until the machine stops.

Example 2: “Café” in Script font
Press the monogram key and select Script font. Enter “C”.

(1)

(1) Monogram key

Press the letter case key and select lower case letters. Enter “a” and “f”.

Press the next page key 3 times to go to page 4/5. Enter “é”.

(2) Next page key

(2) Start sewing. Sew until the machine stops.

99

(6) (7) (8)

(1) (2)
(3) (4)
(5)

Saving a Pattern Combination The pattern combination and monogram can be saved as a file in the machine’s internal memory or a USB flash drive. The machine has a USB port for USB flash drives. Press the function switch key. Press the save file key after programming a pattern combination, and the save file window will open.
(1) Function switch key (2) Save file key Select the location to where you wish to save the pattern combination. The “Ordf” folder is shown and the file name is assigned automatically starting from C_001…..in order.
Select the “Ordf” folder. Press the OK key to save the file under the assigned name.
(3) File name
If you wish to assign a unique name to the file, press the rename key and the keyboard window will open.
(4) Rename key
NOTE: · The files and folders are also displayed on different
pages. Press page keys to switch the window. (5) Page keys
· This model supports FAT16 and FAT32 formats only. If the USB flash drive is not read, check its format (refer to pages 152-153).
· Do not use a USB card reader and USB hub.
If you wish to use a QWERTY layout keyboard, press the keyboard key. Press the upper or lower case key to select letter case.
(6) Upper case key (7) Lower case key (8) Keyboard key Enter a new name and press the OK key to change the file name.
Press the OK key and the file is saved under the new name.

100

(10) (9) (11) (12)

Creating a New Folder Select a location for a new folder and press the new folder key. The keyboard window will open. Enter a folder name and press the OK key. The new folder is created under the assigned name.
(9) New folder key
NOTE: Press the parent directory key to move to the parent directory and display the folder.
(10) Parent directory key
Changing a Folder Name or File Name Press the rename key and select the folder or file of which you wish to change its name. The keyboard window will open. Enter the new name and press the OK key. The name of the folder or file will change.
(11) Rename key

Deleting a File or Folder
Press the delete key and select the file or folder to delete. A confirmation message appears. Press the OK key to delete the file or folder.
(12) Delete key

101

(1) (2)

Opening a Pattern Combination You can open the pattern combination, monogram and tapered stitch saved in the machine’s internal memory or a USB flash drive. Press the open file key and the open file window will open.
(1) Open file key
Select the memory location; either the machine’s internal memory or a USB flash drive. The “Ordf” folder will appear.
NOTE: · If you created any folders before, those folders will
also appear. · If you cannot find the desired folder or the file in the
page, press the next or previous page key to display the other pages.
(2) Next or previous page key
Select the desired folder and the file list will appear. Select the desired file.
The screen will return to the ordinary sewing window showing the saved pattern combination or monogram.

Press one of the layout keys to select the layout of the file list as shown.
(3) Layout keys
(3) 102

(2)

(5) (3) (4)

(5)

(1) (3) (5)
(7) (9) (11)

SEWING APPLICATION

Variety of Sewing Applications

Sewing application is a unique feature that provides you

(1)

with useful sewing applications.

Press the sewing application key and the sewing

application menu will open.

(1) Sewing application key

Press one of the key to select the category.

(2) Sewing key (3) Quilt key

The sewing applications using optional presser feet can be selected by pressing the optional foot key. Please refer to optional feet instructions for usage details.
(4) Optional foot key

NOTE: This category is composed of multiple pages. Press page keys to switch the category pages.
(5) Page keys

Sewing

Press the sewing key and the sewing application menu will open.

The 21 sewing applications are as follows:

(2)

(1) Seaming Woven

(2) Seaming Stretch/Knit

(3) Curve

(4) Topstitching

(4)

(5) Rolled Hem

(6) Overedge Woven

(6)

(7) Overedge Stretch/Knit

(8) Overedge Heavy

(9) Blind Hem

(8)

(10) Shell Tuck (11) Lapped Zipper

(12) Pouch Zipper

(10)

(12)

103

(13) Gathering

(14) Easestitching

(15) Basting

(16) Buttonhole

(13)

(14)

(17) Button

(18) Tacking

(15)

(16)

(17)

(18)

(19) Eyelet

(20) Smocking (21) Fagoting

(19)

(20)

(21)

Quilt

In this category, 10 types of useful stitches for quilting are

available.

(1)

(2)

Press the quilt key and the quilt sewing application menu

will open.

The 10 quilt sewing applications are as follows:

(1) Patchwork Piecing

(3)

(4)

(2) Free Motion

(3) Ruler Work

(4) Variable ZZ

(5) Applique

(5)

(6)

(6) Straight Stitch

(7) Decorative Quilt Stitch

(8) Clasp Stitch

(9) Sashiko

(7)

(8)

(10) Hand-Look QU

(9)

(10)

104

(1) (3) (5) (7) (9)
(1)

Optional Sewing Application

The option category of the sewing application provides you with 10 useful sewing applications.

Press the optional foot key and the optional sewing

(2)

application menu will open.

The 10 optional sewing applications are as follows:

(1) Beading

(4)

(2) Ribbon/Sequin (3) Piping

(4) Cording

(5) Pintucking

(6)

(6) Free Motion Couching

(7) Applique

(8) Ruffler

(9) Ultraglide

(8)

(10) Invisible Zipper/CONCEAL® Zipper*

Refer to the instructions on optional foot for sewing.

• “CONCEAL” is a registered trademark of YKK Corporation.
  (10)

Sewing Press the sewing key and the sewing application menu will open.
(1) Sewing key
Seaming Woven Straight stitches for seaming regular woven fabrics.

105

Seaming Stretch/Knit Narrow stretch stitches for seaming stretch or knit fabrics.
Curve Short straight stitches for seaming curved lines.
Topstitching Long straight stitch for topstitching with thick threads.
106

Rolled Hem

(1) Straight Stitch Rolled hemming with straight stitch

(2) Zigzag Stitch

(1)

(2) Rolled hemming with narrow zigzag stitch

(3) 4 mm & 6 mm

Rolled hemming using optional rolled hemming feet D1

(3)

and D2

0.3 cm (1/8)

5 cm (2)

To sew: Attach rolled hem foot D. Fold the fabric edge twice to form a hem, 0.3 cm (1/8) wide and 5 cm (2) long then press.
Place the fabric aligning the hem edge with the guide of the foot. Turn the handwheel to lower the needle to the starting point. Lower the foot and sew several stitches slowly while pulling on the threads to assist feeding the fabric. Stop the machine and lower the needle into the fabric. Raise the foot and insert the folded portion of the fabric into the curl of the foot.
Lower the foot and sew while lifting the edge of the fabric to keep it feeding into the curl smoothly and evenly.

0.9 cm (3/8) 0.9 cm (3/8)

NOTE: Trim the corners 0.9 cm (3/8) to reduce bulk.
107

Overedge Woven Overcasting stitch for regular woven fabrics.
Overedge Stretch/Knit Knit stitch for finishing raw edges of stretch or knit fabrics. For better results, use zigzag foot A and sew leaving an adequate seam allowance. After sewing, trim the seam allowance close to the stitches (refer to page 49).
108

Overedge Heavy Double overedge stitch for preventing raw edges of linens and gabardines from ravelling.
109

Blind Hem
Select “Blind Hem”. The following 2 options are available. (1)
(1) Woven
For blind hemming regular woven fabric. (2) (2) Stretch/Knit
For blind hemming stretch or knit fabric.

(3)

(A)

(B)

(7)

(4) (3)
(6) (5)

To sew:
Attach blind hemming foot G.
Fold the fabric to form a hem leaving a 0.5 cm (1/4) allowance as shown.
(3) 0.5 cm (1/4)
(A) Medium to heavy fabrics: The raw edge should be overcasted.
(B) Fine fabrics: Fold the raw edge 1 cm (3/8). (4) 1 cm (3/8)
Position the fabric so that the fold comes to the left side of the guide on the foot. Lower the presser foot.
The needle should just pierce the folded edge when it comes over to the left side.
Adjust the position of the needle drop if necessary. Sew guiding the fold along the guide.
(5) Fold (6) Guide (7) Wrong side of the fabric

(8)

After sewing is finished, open the fabric flat.

The seam on the right side of the fabric is almost

invisible.

(7) Wrong side of the fabric

(7)

(8) Right side of the fabric

110

(1)
(3) (2)

Adjusting the needle drop position Press the setting bar to expand the manual setting window.
(1) Setting bar Press the “+” key to move the needle drop positions to the left. Press the “­” key to move the needle drop positions to the right.
(2) “+” key (3) “­” key
The needle drop position will change, while the stitch width (2.8 mm) remains consistent. The distance between the left needle drop position and guide of the foot is indicated in millimeters.
NOTE: You can alter the stitch width by changing the right needle drop position.

2.8 mm

Altering blind hem stitch width

Press the “+” key in (2) to increase stitch width (3).

Press the “­” key in (2) to decrease stitch width (3).

(1)

(2)

NOTE: You can move the left needle drop position (4) with the

“+” or “­” key in (1).

(4)
(3) 111

Shell Tuck Select “Shell Tuck”. The following 3 options are available. (1) Small (1) Narrow shell tuck stitch
(2) (2) Medium Medium width shell tuck stitch
(3) (3) Large Regular shell tuck stitch

To sew:

Use a light weight fabric (Tricot, for example).

(4)

Fold the fabric in bias as shown and stitch on the fold.

(4) Bias direction

Allow the needle to barely clear the folded edge to create a shelled edge.
If you sew shell tucks, space the rows at least 1.5 cm (5/8) apart.

112

Lapped Zipper
Press the Lapped Zipper key and the zipper sewing window will open. Press the sewing step key and the machine setting will automatically adjust to suit each sewing step.
NOTE: Dual feed plus foot VD and dual feed plus zipper foot ED appear on the visual touch screen when the dual feed key is pressed. Dual feed plus zipper foot ED is used with dual feed plus foot VD together.

• Dual feed feet and holder are optional items (sold separately).

(4)

(2)

(1)

(3) Lock-a-Matic

Basting

(5)

Fabric preparation Add 1 cm (3/8) to the zipper size. This is the overall opening size. Mark the end of opening.
(1) Zipper size (2) Opening size (3) 1 cm (3/8) (4) End of opening Attach zigzag foot A.
Lock-a-Matic Place the right sides of the fabric together and sew to the end of the opening leaving a 2 cm (3/4) allowance.
(5) 2 cm (3/4)
Basting Baste the zipper opening.
113

(6) (7)

Sew Left side
Replace the foot with zipper foot E.
Fold back the left seam allowance. Turn the right seam allowance under to form

References

• Elna master shop – Swiss design
• Optional accessories – Elna master shop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>