amazon basics B08J4MPXHJ Electronic Touchscreen Deadbolt Door Lock With Passge Lever Instruction Manual
- May 15, 2024
- amazon basics
Table of Contents
Installation Manual
B08J4MPXHJ Electronic Touchscreen Deadbolt Door Lock With Passge Lever
Electronic Touchscreen Deadbolt Door Lock with Passage Lever 
Product Description
1.1 Electronic lock 
A Key
B Cylinder
C Exterior touchpad
D Latch
E Latch face plate x2
F Drive-in collar
G Screw x5
H Strike plate
I Mounting plate
J Bolt x2
K Interior assembly
L scewss X3
M Battery compartment cover
1.2 Passage lever
N Exterior lever (with
bracket)
O Latch
P Latch face plate x2
Q Drive-in collar
R Screw x4
S Strike plate
TV Interior chassis
U Boltx2
V Interior rose
W Interior lever*
X Lever catch tool
“Parts pre-assembled
Installation
NOTICE
This product is classified as “full indoor type” and should only be installed
in indoor environment.
NOTICE
Determine the door handing before installing the product.
Face the door from the exterior side:
- If the hinges are installed on the left, the door is left-handed.
- If the hinges are installed on the right, the door is right-handed.
NOTICE
The turn plece is located on the interior assembly (K) installed on the
interior side of the door. For left-handed doors, rotate the turn piece 452
clockwise. For right-handed doors, rotate the turn piece 452 counter-
clockwise.
NOTICE
- Prepare all the tools required for the installation.
- Follow the steps in chapter “Instructions for doors with existing holes” at the back of the manual to install the electronic lock (P. 21-29) and passage lever (P. 30-38). For drilling, read chapter “Drilling instructions” (P. 39-45).
- lllustrations in the steps in chapter “Instructions for doors with existing holes” and “Drilling instructions” are for left-handed doors. Reverse the lever position for right-handed doors.
Instructions for doors with existing holes
Confirm that the hole in
door edge is @1 (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″
(45 mm) thick. Also confirm that the hole in the door is @2-1/8″ (54 mm).
Hold the latch (D) with the latch face flush
against the door edge. Ensure that the slot is centered in the door hole.
Adjust the latch if needed. 
Optional – for doors with
chiseled pocket: pry open the attached latch face plate (E) and replace it
with the rectangular one. 
Optional – for doors
without chiseled pocket: pry open the face plate holder with a flat-head
screwdriver. Attach the drive-in collar (F) to the latch. 
For latch with face plate (E): it the latch into the hole and
secure with two screws (G). / For latch with drive-in collar (F): insert the
latch with drive-in collar and tap into position using a wood block and
hammer. 
Mount the exterior
touchpad (C) on the door and run the cable through the door hole under the
latch. The torque blade of the cylinder (8) must pass through the slot on the
latch (D).
Pass the mounting plate (1) through the torque
blade and fix it with two bolts (J). Connect the cables aligning the red edge
of the connector. 
Remove the battery
compartment cover (M). Secure the interior assembly (K) on the door with the
screws (G, L). Make sure the latch bolt is in the unlocked position when
finished. 
Ensure that the door
frame hole is at least 1* (25 mm) deep. Mount the strike plate (H) on the door
frame with two screws (G). 
Confirm that the hole in
door edge is @1″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″
(45 mm) thick. Also confirm that the hole in the door is @2-1/8″ (54 mm).
Hold the Latch (0) with the latch face flush
against the door edge. Ensure that the square hole is centered in the door
hole. Adjust the latch if needed. 
Optional – for doors with chiseled pocket: pry open the
attached latch face plate (P) and replace it with the rectangular one.
Optional – for doors without chiseled pocket: pry
open the attached latch face plate (P). Remove the face plate holder and
attach the drive-in collar (Q). 
Latch with face plate (P): fit it into the hole and secure with two screws
(R). / Latch with drive-in collar (Q): insert it and tap into position using
awood block and hammer. Latch bolt bevel must face to closing direction.
Mount the exterior lever (N) on the door. The
middle bolt of the lever must pass through the slot on the latch (0). Use the lever catch tool (X) to detach the interior lever (W)
from the interior rose (V). Pry open the interior chassis (T).
Mount the interior chassis (T) on the door with two bolts (U).
Attach the interior rose (V) and interior lever (W) on the liner. Ensure the
orientation of the interior chassis (T) for the door is correct. Ensure that the door frame hole is at least 1* (25 mm) deep. Mount the strike plate (S) on the door frame with two screws (R). Use template to mark two pairs of holes on door. Fold template
along fold line and place it along the door edge. Select the drilling point
for different door thickness: 1-3/8″ (35 mm), 1-9/16″ (40 mm) or 1-3/4″ (45
mm).
Dorilt the pairs of holes using chisel and
circular drill bits.
NOTICE
Drill from one side until the drill just breaks through, then complete hole from the other side to prevent wood from splintering.
Mark the outline of the face plate (E, P). Chisel 5/32″ (4 mm)
deep for the face plate (E) and 1/8″ (5 mm) for the face plate (P). Mark the positions of the screw holes. Drill two 1″ (25 mm)
deep holes using 1/8″ (3 mm) dill bit.
Close the door and mark the top and bottom position of the
latch across the door frame. Open the door and measure the distance X from the
exterior door edge to the flat end of the latch. 
Mark a vertical line on the door frame for the measured
distance X rom the outside to the inside. Position the strike plate (H, S)
within the guidelines. Mark and drill two 1″ (25 mm) deep screw holes using
1/8″ (3 mm) drill bit.
Mark and drill a 17 (25
mm) deep hole for the electronic lock and a 1/2″ (13 mm) deep hole for the
passage lever at intersection of horizontal and vertical line of the cutout of
the strike plate (H, S). 
hisel 5/64″ (2 mm) deep
for the strike plate (H) and 1/16″ (1.6 mm) eep for the strike plate (S).
amazon.com/AmazonBasics
MADE IN TAIWAN
V03-10/22
Documents / Resources
|
amazon basics B08J4MPXHJ Electronic Touchscreen Deadbolt Door Lock With
Passge
Lever
[pdf] Instruction Manual
B08J4MPXHJ Electronic Touchscreen Deadbolt Door Lock With Passge Lever,
B08J4MPXHJ, Electronic Touchscreen Deadbolt Door Lock With Passge Lever,
Touchscreen Deadbolt Door Lock With Passge Lever, Deadbolt Door Lock With
Passge Lever, Passge Lever
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>