Terucle HG4-25 Gravity Gesture Sensing Remote Control Car Toys User Manual

Terucle HG4-25 Gravity Gesture Sensing Remote Control Car Toys

INSTRUCTIONS

Thank you for using our company’s toy products. In order to have a better understanding of this product, please read the following instructions before use, which will bring you a different operating experience.

NOTE

Warning: please do not disassemble or modify the product without authorization, any changes may cause the product to not work properly.

SPECIAL WARNING

The used output power of charging plug should be 5V. Please do not use the quick-charging plung chargik causes ovable ate a battery ich thing aditi re stht i dangerous matters such at product burnout.

Product Configuration

Car Battery Installation

Battery installation
Open the body battery cover, Connect the rechargeable battery pack to the power socket, Close the battery cover.

 Battery Charging Mode

1. Connect the Rechargeable battery pack to the USB charging cable
2. Plug the other end of the USB charging cable into the USB port for charging

R/C Function introduction and battery installation

1. Press down the “Demo” key: the R/C car enters the automatic demonstration mode; press any key to exit from the automatic demonstration mode.
2. Press down the “Music” key: Press the first time to play the engine sound, Press the second time to play music, Press for the another music a third time, and press the fourth time to close the music.
3. The effective control distance of the handle remote controller is about 40m.

Battery installation

Open the body battery cover and install 2×1.5V “AA” non-rechargeable batteries in the right polarity direction and cover the battery cover. (Battery not included)

Gravity sensing watch remote control battery description
Gravity Induction remote controls (Operate as shown below)

1. Built in 3.7V lithium battery

2. 3V CR2032 button battery

3. Connect the Gravity Induction R/C to the USB charging cable

4. Plug the other end of the USB charging cable into the USB port for charging

INSTALL THE BATTERY

Open the battery cover, Install 3V CR2032 button battery, Close the battery cover.

PRECAUTIONS FOR BATTERY USE

• Before playing please charge the new battery pack.

• The output power of charging plug is 5V;

• The higher the actual milliampere of the rechargeable battery, the longer the charging time;

• Rechargeable batteries can only be charged under adult supervision;

• During charging, the light of the USB charging cable head is on red. When the light goes out, it indicates that the lithium battery is fully charged. The charging time is 3-4 hours.

• First plug the battery pack plug in the charger, then plug the charger plugged in the socket.
  Take out and put in the battery according to the mark on the toy battery room;

• Non-rechargeable batteries cannot be charged;

• Use only the same or identical battery as recommended;

• Do not mix-use old and new batteries or different types of batteries;

• Batteries should be placed in the correct polarity;

• Remove the exhausted battery from the toy;

• Power terminals should not be short-circuited;

• The charger must be checked regularly for damage to its wires, plugs, housings and other components. If damage is found, stop using the charger until it is repaired.

Handle Remote Control frequency alignment

1. First, turn on the power switch of the automobile body. The light of the automobile body flashes. Then, turn on the power switch of the remote controller, and start frequency alignment. When the frequency alignment succeeds, the light of the automobile body goes on.
2. When the frequency alignment fails, the power light of the remote controller and the light of the automobile body flash continuously. When the connection fails, please repeat the above operations.
3. If there is no operation after Connection frequency, the remote control car and the remote control enter the sleep mode, and the frequency needs to be re-linked.

Handle Remote Control Operating instructions

Gravity induction watch R/C frequency alignment

1. Long press the power switch of the gravity remote controller to start the frequency alignment. When the frequency alignment succeeds, the light 2 and light 3 of the remote controller go on. In case of no operation, the sleep mode starts one minute later
2. When the frequency alignment fails, the light 1 and light 4 of the remote controller flash continuously. When the connection fails, please repeat the above operations.
3. If there is no operation after Connection frequency, the remote control car and the remote control enter the sleep mode, and the frequency needs to be re-linked.

General Trouble Shooting

Instructions

Battery chargers that use this toy must be regularly checked to prevent damage to the wires and other components and. if damaaed. must be repaired for damage.

Maintenance Matters

1. Can not close to the fire, avoid direct sunlight, high temperature and humidity or long-term in the car, to avoid short circuit, fire.
2. Control plack hao the color box packaging, to avoid damage. A motion during to sport or storage.
3. Remote control car with a damp cloth to gently wipe.

TIPS

To The Consumer

1. When playing remote control car indoors, please be careful not to damage furniture or glass.
2. Please play outside in a safe place. Do not play remote control car in the road and the crowd, so as to avoid danger.
3. Play remote control car to hear thunder outdoors, should immediately stop playing.
4. When the wheel is rotating, do nt drop your hand near to avoid injury, but also not to be involved in hair, clothes and so on.
5. Do not drive the remote control car facing people.
6. Do not throw the remote control car, chaos collision.
7. When placing the remote control car, please keep it away from fire and high temperature.
8. The car use a complex electronic circuits and a large number of components, please do not disassemble or modify the circuit board.
9. Remote control car after playing with dirt, dust must be gently wiped with a damp cloth.
10. Do not put the toy in the water, it will damage the electronic components.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>