ROLLING SQUARE B0C659SJH2 Edge Pro Full Kit User Manual

May 15, 2024
ROLLING SQUARE

ROLLING SQUARE B0C659SJH2 Edge Pro Full Kit

ROLLING-SQUARE-B0C659SJH2-Edge-Pro-Full-Kit-PRODUCT

Specifications

  • Plate remover
  • Nanosuction layer
  • Metal disc
  • Metal plate
  • Plate protection layer
  • Metal ring
  • Ring aligner

Product Usage Instructions

Attaching Metal Plate to Laptop

  1. Remove the sticker’s protective film from the Plate protection layer.
    • Ensure no more than 10mm from the edge of the laptop.
  2. Attach the Metal plate in the middle of the Plate protection layer.
    • Use the Aligner to stick the Magnetic ring on the back of your phone (not needed for iPhone 12 or later).
  3. To remove the Metal plate from your Laptop, insert the Plate remover under the plate and start sliding gently. Use protective gloves.

Attaching Metal Disc to Tablet

  1. Remove the sticker’s protective film from the Metal disc.
    • Ensure no more than 10mm from each side of the Tablet.
  2. Attach the Metal Discs to the back of your Tablet.
    • Snap your Tablet to the Laptop and adjust the Core inclination for the perfect viewing angle.
  3. To remove the Metal disc from your Tablet, insert the Plate remover under the disc and slide gently. Use protective gloves.

Attaching Nanosuction Layer to Wall

  1. Remove the sticker’s protective film from the Metal disc.
  2. Attach the Nanosuction layer on the adhesive side of the Metal disc.
  3. Attach the Metal disc to your desired surface.

FAQ

  • Q: How do I adjust the inclination for the perfect setup?
  • A: You can adjust the inclination by following the provided guidelines in the User Manual. For different products, adjust as necessary to find your preferred setup.
  • Q: How do I switch between light modes on the BUTTON?
  • A: Click the button to light it up. The first five clicks allow you to switch between 5 different light modes. Hold for 2 seconds to turn off the light.

Components

ROLLING-SQUARE-B0C659SJH2-Edge-Pro-Full-Kit-FIG-1

Installation Instructions

EDGE Pro® Core – Laptop / Smartphone standard use

  • Remove the sticker’s protective film from the Plate protection layer.

  • Attach the Plate protection layer in the middle of the laptop, leaving no more than 10mm from the edge of the laptop.

  • Remove the sticker’s protective film from the Metal plate.

  • Attach the Metal plate in the middle of the Plate protection layer.

  • Use the Aligner (C) to stick the Magnetic ring (D) on the back of your phone (not needed for iPhone 12 or later).

  • Adjust the EDGE® Pro Core inclination to reach the perfect angle of view.

  • Snap your phone to the EDGE® Pro Core and enjoy your journey.

  • To remove the Metal plate from your Laptop insert the Plate remover under the plate and start sliding very gently to remove the Metal plate.

  • Be extremely careful and use protective gloves.

EDGE Pro® Core – Laptop / Smartphone alternative use

  • Remove the sticker’s protective film from the Plate protection layer.
  • Attach the Plate protection layer on the laptop, leaving no more than 10mm from the side of the laptop and no more than 20mm from the top.
  • Remove the sticker’s protective film from the Metal plate.
  • Attach the Metal plate in the middle of the Plate protection layer.
  • Snap your phone to the EDGE® Pro Core to use it in landscape mode.
  • Rotate your EDGE® Pro Core and your smartphone by 90° to use it in landscape mode.
  • If you are using an iPhone with an Apple computer you can also rotate it by 180° to use Apple Desk View.

EDGE Pro® Core – Laptop / Tablet standard use

  • Remove the sticker’s protective film from the Metal disc.

  • Attach the Metal Discs (E) to the back of your Tablet and leave no more than 10mm from each side (G, F)

  • Snap your Tablet to the Laptop, and adjust the Core inclination to reach the perfect angle of view.

  • To remove the Metal plate from your laptop insert the Plate remover under the plate and start sliding very gently to remove the Metal plate.

  • Be extremely careful and use protective gloves.

EDGE Pro® Core – Standalone use

  • Open the EDGE® Pro Core and attach it to your smartphone to use it as a stand.
  • Rotate your smartphone by 90° to use it in landscape mode.
  • Attach 2 EDGE® Pro Core to your tablet to use them as a tablet stand.

EDGE Pro® Core – Use on any surface

  • Remove the sticker’s protective film from the Metal disc.
  • Attach the Nanosuction layer on the adhesive side of the Metal disc.
  • Attach the Metal disc to your wall, kitchen cabinet or any surface you want.
  • Attach the EDGE® Pro Core to the Metal disc to mount your smartphone on the wall or any surface.

Note: You can directly attach the EDGE® Pro Core to any metallic surface without using the Metal disc.

EDGE Pro® Wireless Charger

  • Snap the EDGE® Pro Wireless Charger to the EDGE® Pro Core and plug the USB-C connector in a USB-C port.
  • Adjust the inclination to find the perfect setup
  • Snap your phone to the EDGE® Pro Wireless Charger and start charging your phone.
  • You can also plug the EDGE® Pro Wireless Charger into any USB-C wall charger.

EDGE Pro® Light

  • Snap the EDGE® Pro Light to the EDGE® Pro Core and click the button to light it up. The first five clicks allow you to switch between 5 different light modes. Hold for 2 seconds to turn off the light.
  • Adjust the inclination to find the perfect setup.
  • The EDGE® Pro Light works for 60 minutes at its maximum intensity, 5 hours at its minimum intensity. EDGE® Pro Light can be recharged with the USB-C to USB-C cable provided in the pack. You can also keep it plugged in while using it.
  • You can also snap the EDGE® Pro Light to an EDGE® Pro Core attached to your smartphone to use it as an additional photography light.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals