Panamorph 133 Alpha Anamorphic Lens Installation Guide

: May 15, 2024
: Panamorph

Table of Contents

Panamorph 133 Alpha Anamorphic Lens
Product Usage Instructions
Alpha 133 Lens Installation Steps
CLEANING
LIMITED WARRANTY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Panamorph 133 Alpha Anamorphic Lens

Product Specifications

Model: Alpha 133
Compatibility: Sony VPL-XW5000ES, VPL-XW6000ES, VPL-XW7000ES projectors
Aspect Ratio: 2.4:1
Lens Mode: 1.32x
Optical System: Precision all-glass optical system

Product Usage Instructions

Step 1: Attaching XM3 Steel Plate
Attach the XM3 steel plate to the ceiling mount holes in the bottom of the projector using M5 screws. Use longer screws if needed for a secure installation.

Step 2: Attaching Lens Bracket
Attach the lens bracket to the Alpha using four #8-32 screws. If the projector is shelf-mounted, attach the lens bracket underneath the Alpha without using black plastic spacers.

Step 3: Installing the Projector
Use horizontal lens shift to center the light beam horizontally in the projector lens. Adjust roll, tilt, and yaw to ensure the test pattern is square and centered on the screen before installing the Alpha.

Step 4: Attaching Alpha to XM3 Steel Plate
Push the lens back to leave a ~6mm gap to the projector lens, then tighten the thumb knobs to secure the Alpha.

Step 5: Adjusting Alpha Height
Loosen the height adjust screws and adjust the bracket arms so that the projector beam passes through the vertical center of the lens. Tighten the height adjust screws once adjusted.

Step 6: Fitting a 2.4:1 Movie to the Screen Width
Set Anamorphic Lens Mode to 1.32x, Aspect to V-Stretch, and play a 2.4:1 movie. Zoom out to fill the screen width for optimal viewing.

Step 7: Adjusting Image Height
If necessary, loosen the tilt adjust screws and tilt the Alpha to move the image. Adjust projector vertical shift as needed to align the image back on the screen.

Step 8: Squaring Up the Image to the Screen
If needed, raise one side of the Alpha or shim the XM3 plate to square up the image. Ensure the lens is level with the projector and screen by adjusting as necessary.

Step 9: Fine-Tuning Panel Alignment
If required, use the Panel Alignment feature in the projector after installing the Alpha for precise panel alignment.

Step 10: Getting Familiar with Projector Settings
Explore and adjust projector settings as needed for optimal viewing experience.

Frequently Asked Questions (FAQ):

Q: How do I adjust the aspect ratio for different content?
A: Set Anamorphic Lens to 1.32x and Aspect to V-Stretch for 2.4:1 movies. For subtitles or different content formats like 2.0:1 or 16:9, adjust settings accordingly.

Sony VPL-XW5000ES, VPL-XW6000ES and VPL-XW7000ES home theater projectors

Over 2 million more pixels on your screen for stunning detail and 30% higher brightness when showing content in the 2.4:1 format.
Patented, sealed, precision all-glass optical system supports distortion-free 8K projection. The ﬁrst of its kind in the history of theater.
Instant aspect ratio changes. No moving parts.
Allows up to 5% larger 2.4:1 screen width (see online Alpha Lens Selector).
Optimized for vertical position of the projector in typical home theaters from -6″ to + 16″ from screen top and +/- 4” from screen horizontal center (greater with higher throw ratios).
Optional UltraWide 2.4:1 mode for 16:9 content to ﬁll a cinema-format 2.4:1 screen.
Universal ceiling- or shelf-mount attachment system for all three XW Sony projector models. Likely compatibility with future projectors (not guaranteed, new mount may be required).
Weight: Lens and bracket: 4.7 pounds (2.14Kg). XM3 plate: 4 pounds (1.8Kg).
Dimensions: Lens only: 6.6” (168mm) W X 5.6” (140mm) H X 5.9” (150mm) D. Allow 6.5” (165mm) in front of the projector for mounting and adjustments.

Alpha 133 Lens Installation Steps

ATTACH THE XM3 STEEL PLATE USING M5 SCREWS THROUGH THE CEILING MOUNT (if used) AND INTO THE PROJECTOR CEILING MOUNT HOLES. Use longer screws as necessary for a secure installation.
ATTACH THE LENS BRACKET TO THE ALPHA with four #8-32 screws (see below). However, if the projector is shelf mounted then attach the lens bracket so it is underneath the Alpha instead and do not use the black plastic spacers (see illustration on back page).
INSTALL THE PROJECTOR. Use horizontal lens shift to center the light beam horizontally in the projector lens. Adjust roll, tilt and yaw so the test pattern is square to and centered on the screen before installing the Alpha.
ATTACH THE ALPHA TO THE XM3 STEEL PLATE, push the lens back leaving a ~6mm gap to the projector lens, then tighten the thumb knobs.
ADJUST THE ALPHA HEIGHT. Loosen the height adjust screws and adjust the bracket arms so that the projector beam passes through the approximate vertical center of the lens, then tighten the height adjust screws.
FIT A 2.4:1 MOVIE TO THE SCREEN WIDTH: a) set the Anamorphic Lens Mode to 1.32x; b) set Aspect to V-Stretch c) play a 2.4:1 movie (no longer use the test pattern) and d) zoom out to ﬁll the screen width.
ADJUST THE IMAGE HEIGHT (if necessary). Loosen the tilt adjust screws and tilt the Alpha to move the image one way while adjusting the projector vertical shift to move the image back to screen. The change in image height will be very subtle.
SQUARE UP THE IMAGE TO THE SCREEN (if necessary) by raising one side of the Alpha or even by shimming the XM3 plate. If the image is “tilted” then it means the lens is not level to the projector and screen. Finally, loosen the thumb knobs and push the Alpha back to just barely touch the projector lens.
FINE TUNE PANEL ALIGNMENT (if necessary) using the Panel Alignment feature in the projector AFTER the Alpha is installed.
GET FAMILIAR WITH PROJECTOR SETTINGS.
Set “Anamorphic Lens” to 1.32x and “Aspect” to V-Stretch.
If subtitles are missing, use the 2.0:1 or 16:9 content settings.
Set “Anamorphic Lens” to 1.32x and “Aspect” to V-Stretch. Note: 11% of content will be cropped from top and bottom.
Optional: Set “Anamorphic Lens” to 1.24x and “Aspect” to V-Stretch to vertically squeeze content by 7% to show more on the screen.
If subtitles are still missing, use the 16:9 content settings.
Set “Anamorphic Lens” to 1.32x and “Aspect” to Normal. Note: Content will appear 25% horizontally stretched.
Optional: Set “Aspect” to Squeeze to add black sidebars and to remove the stretched appearance.

Alpha mounting conﬁguration for a high, shelf-mounted projector. XM3 plate mounts to the ceiling mount holes in the bottom of the projector. Note the bracket is inverted so that the Panamorph logo is toward the ﬂoor.

CLEANING

Small amounts of dust and wipe marks are very noticeable on lens surfaces with a high brightness projection beam but typically will not impact the image as much as damage from excessive cleaning in pursuit of a “perfect” optical surface. Occasionally blowing oﬀ the lens surfaces with clean air is the best way to keep long term performance. If there is any excessive residue or build- up then it is recommended that you clean the optics with professional lens cleaning supplies such as from a camera store while the lens is in front of the lit beam of the projector. This will allow you to quickly see if the cleaning process is causing any damage.

LIMITED WARRANTY

Panamorph, Inc. warrants this product against any change in performance or functionality for a period of twenty-four months from our ship date. During this period, a unit may be repaired or replaced, at the discretion of Panamorph, Inc., by returning it in its original packaging with a copy of your receipt. This warranty does not cover damage resultant from lack of prudent care, accident or misuse (including use with other products in ways not intended); any cosmetic damage not reported within 15 days of purchase; or any performance change caused by the environment in which it is used. All damages are limited to the cost of the product.