Panamorph CDR-E1 Direct Attach Cinema Format Conversion Lens Installation Guide

: June 4, 2024
: Panamorph

Table of Contents

IMPORTANT THEATER GUIDANCE
CDR-E1 Installation Steps
CLEANING
LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CDR-E1 Direct Attach Cinema Format Conversion Lens
Installation Guide

CDR-E1
Direct Attach Cinema Format Conversion Lens
INSTALLATION GUIDE
(Phillips #2 screwdriver required)
For use only with the
Epson LS12000
projector Short Leg on Right

IMPORTANT THEATER GUIDANCE

The projection screen should be ﬂat, in the 2.4:1 aspect ratio, and with a minimum 2.0” screen border.
The projector lens center should be between -2 and +6 inches from the top edge of the screen surface (about +3 inches is ideal) and horizontally centered on the screen +/- 3 inches.
The throw ratio (throw distance divided by screen surface width) should be at least 1.4:1.
Edge curvature/distortion of the image is most noticeable at low throw ratios so longer throw distances are encouraged. The screen border should be used to mask edge curvature of about 1.5” at a 1.4:1 throw ratio; about 1” at 1.6:1; with progressively less edge distortion visible as the throw ratio increases. If desired, use the Epson LS12000 “Point Correction” for ﬁnal distortion adjustments and then “Panel Alignment” only after ﬁnalizing lens setup.

CDR-E1 Installation Steps

INSTALL THE PROPER LENS RETAINER. Remove the two front Phillips assembly screws and remove the rear retainer. Use this retainer for a ceiling-mounted projector. Use the other retainer provided for a high shelf-mounted projector (see illustration on reverse). Manually open the projector lens door. The lens will prevent door closure but this will not harm the projector. Squeeze the retainer and work it into the projector opening to nest into the inside rim of the projector housing with prongs toward the ceiling.
PREPARE THE PROJECTOR. Make sure the projector lens is horizontally centered in its opening (ie little or no horizontal lens shift). Adjust the projector roll, tilt, and/or yaw so the projector test pattern lines are square to the screen edges and the test pattern is centered on the screen. Then show a 2.4:1 movie. Use the Epson “Aspect” button on the remote to select “Anamorphic Wide” and make sure the projector lens is clean and as dust free as possible.
INSTALL THE CDR LENS. After removing the rear CDR lens cover, install the CDR lens/mount assembly over the retainer prongs. The lens may have some rotational play so rotate as necessary until a stop is felt at which point the lens is vertically aligned with the projector. Insert and tighten the two assembly screws to secure (do not over) tighten Remove the front protective ﬁlm.
ADJUST THE LENS TILT AND PROJECTOR SHIFT. Adjust the projector lens zoom to ﬁll the width of the screen with the 2.4:1 movie. Tilt the CDR lens and adjust the projector vertical lens shift to make sure the beam is getting through the CDR lens to ﬁll the screen. There is only a slight variation in vertical image height with this adjustment but experimentation may lead to the best ﬁt and geometry. Lock the CDR lens tilt by tightening the single Phillips tilt lock screw (do not over-tighten). As desired you may want to apply additional “Point Correction” and/or “Panel Alignment” at this time (see Epson manual).
DECIDE HOW TO WATCH 16:9 CONTENT (including menus).
Use the Epson “Aspect” button on the remote to select “Horiz.
Squeeze” to watch 16:9 content in the center of the screen or select “Auto” to stretch 16:9 content to ﬁll the entire screen.

CLEANING

Small amounts of dust and wipe marks are very noticeable on lens surfaces with a high-brightness projection beam but typically will not impact the image as much as damage from excessive cleaning in pursuit of a “perfect” optical surface. Occasionally blowing oﬀ the lens surfaces with clean air is the best way to maintain long-term performance. If there is any excess residue or build-up then it is recommended that you clean the optics with professional lens cleaning supplies such as from a camera store while the lens is in front of the lit beam of the projector. This will allow you to quickly see if the cleaning process is causing any damage.

LIMITED WARRANTY

Panamorph, Inc. warrants this product against any change in performance or functionality for a period of twenty-four months from our ship date. During this period, a unit may be repaired or replaced, at the discretion of Panamorph, Inc., by returning it in its original packaging with a copy of your receipt. This warranty does not cover damage resultant from lack of prudent care, accident or misuse (including use with other products in ways not intended); any cosmetic damage not reported within 15 days of purchase; or any performance change caused by the environment in which it is used. All damages are limited to the cost of the product. This warranty is not transferable.