Coleman NWL0001367151 Classic OutdoorXL Awning Instruction Manual
- May 15, 2024
- Coleman
Table of Contents
Coleman NWL0001367151 Classic OutdoorXL Awning
Product Information
Specifications
- Model : Coleman Awning
- Part Number : NWL0001367151 (ECN0056683-B)
Description:
The Coleman Awning is designed to provide shade and protection for outdoor activities. It is a durable and high-quality product that requires proper setup and maintenance for optimal performance.
Product Usage Instructions
Setup Instructions
- Place the awning parallel to the van with approximately 1m space between them.
- Loosely peg the four main corners of the awning using large plastic pegs.
- Insert fiberglass poles and secure them in place with steel pegs.
- Attach the removable Kador strip and figure of 8 sections.
- Adjust tension using the straps on each side of the tunnel.
- Square out the corners and secure them with V-shaped metal pegs.
- Continue securing with steel and plastic pegs along the sides as needed.
Removal Instructions:
To remove the awning, follow these steps:
- Unclip and detach all poles and pegs.
- Fold the awning and roll it up to fit into the transport bag.
Maintenance and Cleaning:
Proper maintenance is essential for the longevity of your awning. Here are some tips:
- Regularly inspect for any damage or wear.
- Clean with mild soap and water, avoiding harsh chemicals.
- Allow the awning to dry completely before storing.
FAQs
- Q: Do I need to purchase the removable Kador strip and figure of 8 sections separately?
- A : Yes, the removable Kador strip and figure of 8 sections are sold separately and are essential for the proper setup of the awning.
- Q: How do I prevent condensation inside the awning?
- A : Ensure adequate ventilation by opening windows or vents to prevent condensation buildup inside the awning during certain weather conditions.
Dear customer,
Congratulations on your purchase of a Coleman awning.
We take pride in bringing you a quality product that will offer you years of
pleasure. Your new item is an investment that deserves your care and
attention. This manual has been compiled to help you to operate your product
correctly. It contains details of the product, its equipment, and information
on its operation and maintenance. Read it carefully and familiarize yourself
with the product before using it.
CAUTION: It is the owner’s responsibility to make sure that all users will carefully read and follow the manual and instructions for the safe operation of this product.
Important Notice: Under certain weather conditions, condensation can
occur on the inside surface of your awning.
To prevent condensation in your awning, please ensure adequate ventilation.
Condensation should not be confused with leaking.
- Always practice at home prior to your first usage on the campsite. Always follow the setup/inflation instructions written in this manual.
- Find flat ground, far from trees to avoid falling branches or sticky tree sap that could damage your awning.
- Be sure the area is clear of sharp stones, rocks, and debris to avoid damaging the groundsheet.
- Unpack the awning and clearly identify all separate parts of your awning – Awning, Pole bag, Stakes bag, and Repair Kit.
- Unroll and lay your awning flat in the required position next to your vehicle. The awning connection tunnel shall face your campervan side entrance.
- Try to set up your awning with main entrance facing away from the wind.
Set-up Instruction
NOTE: Note that the removable Kador strip and figure of 8 sections are sold separately.
- First, take the awning and place it parallel to the van. Leave approximately 1m space between the main body of the awning and the van.
- Simulate hanging/positioning the connection tunnel to check if you are at the right distance, then place your tunnel back on the ground.
- Loosely peg the four main corners of the awning using the large plastic pegs to secure in position.
- Insert a fiberglass pole into the front pole sleeve of the awning, locate over-attached steel pins on either side, and clip the flysheet to the poles.
- Raise the pole using the front two storm straps and loosely secure in place with large steel pegs
- Working backward towards the rear of the awning insert, pin, and clip the remaining poles.
- Before squaring out, close all of the awning’s main doors.
- Depending on the attachment system that you have on the van, feed the removable Kador strip into your C rail or retractable awning (Kador strip sold separately).
- Then, feed the first figure of 8 sections onto the Kador strip (sold separately).
- Feed the attached Coleman 6mm beaded awning strip onto the Figure of 8 section (see Fig F).
- Slide on the remaining figure of 8 sections until the full length is attached.
- You can then adjust the tension of your awning using the straps on each side of the tunnel (Fig. B).
- Starting at the rear of the awning, square out the corners and back and securely peg using the V-shaped metal pegs. The adjustable straps will ensure correct tension. (Fig. A)
- Placing pegs
- Working towards the front, continue to insert the steel pegs along the sides of the awning. (Fig C).
- Use plastic pegs for guylines and storm straps. (Fig. D)
- Use flat-head steel pegs to lay flat the main dropdown doorway as well as the strap that sits at the base of the porch (Fig. E).
- Always use all of the guy lines and storm straps and take care that the awning does not become distorted. Guy lines and storm straps tension by adjusting using their runners or buckles. Check guy lines and storm straps regularly and re-tension when necessary.
Removal Instructions
- Open inner awning doors.
- Open all main doors (including mesh doors) to ensure air easily exits the tent when rolling, prior to placing in the bag.
- Unpeg guy line and stake points. Detach your awning from the vehicle rail.
- Remove all fiberglass poles from each pole sleeve, fold them, and place in the pole bag.
- Lay the awning flat.
- Fold the awning and roll it to fit the carry bag.
- Store pegs and poles bags in the carry bag.
- Ensure your awning is totally dry before storing to ensure it is at its very best and ready for its next use.
Care, Storage, Cleaning
- Store your awning in a dry, cool, well-ventilated space clean from dirt and debris. Never leave your packed awning in direct sunlight – choose a dark area.
- Muddy awnings can only be washed using clean water and a soft sponge. Never use detergent, soaps, or a brush on your awning – as this could damage fabrics and reduce the waterproof properties of your awning.
- Never spray insecticides on or in the awning – as this could damage fabrics and reduce the waterproof properties of your awning.
- Should a waterproof seam tape become detached, this can be repaired by removing the loose part and using a seam sealer (inside) combined with a waterproof spray (outside) to re-seal the seam.