MUD UK MUD-0069 Double DIN Td5 Console Installation Guide
- June 4, 2024
- MUD UK
Table of Contents
MUD Double DIN Td5 Console Installation
MUD-0069 Double DIN Td5 Console
The MUD Double DIN Td5 Console is a direct replacement for the original
factory-fit radio console fitted
All of the original dashboard fasteners are reused to install the MUD Double
DIN Console. There’s no need to remove the radio before removal of your
original Td5 radio console. Swapping the console is an easy DIY task requiring
nothing more complex than the removal of screw fixings. There are, however,
screw fixings of different lengths so take your time and make a note of which
screws go where!
When developing this product we discovered that despite ‘Double DIN’ being an
industry-standard dimension, no two brands of Double DIN mounting cage were
ever the exact same size…
To ensure a perfect fit for all brands of head unit we erred on the side of
caution and have made the Double DIN aperture within this product fractionally
undersize. Use a file or emery/sand paper to remove just enough of the plastic
material to create a snug fit for your mounting cage.
We recommend installing your mounting cage within the MUD Double DIN Console
before commencing installation in the vehicle or transferring over the
switches.
Removal of the original Td5 Radio Console. To gain access to the fixings
holding the radio console in place, first you’ll need to remove the dashboard
top rail from the vehicle.
Remove the screen vent fixings marked in red x q. Remove the dashboard top
rail fixings in yellow x 3.
Remove the instrument binnacle fixings x 4..
Remove the heater control fixings x 2 (yellow) and loosen the lower fixing circled (red).
Carefully pull the binnacle and heater control assembly away from the dashboard just far enough to clear the dashboard top rail. You do not need to disconnect any of the electrical connections.
Locate and remove the two concealed screws that go upwards into the dashboard top rail to either side of the radio console.
Prise out the oval Land Rover insert from the passenger side grab handle to reveal the fixing screw underneath the insert. Remove this screw. Remove the lower fixing screw.
With the grab-handle fixing screws removed, the grab-handle will now lean outwards just far enough from the end of the dashboard to release the dashboard top rail.
With the dashboard top rail removed you can now see how the original center
console is fixed in place. It is held in place with a total of five screws.
All of these fixing screws will be reused when installing the MUD Double DIN
Console.
Remove the two bottom screws securing the radio console to the lower portion
of the dashboard.
Loosen the three screws across the top of the radio console. You DO NOT need to remove these screws completely since you’ll notice the three plastic locating tabs on the top of the console are slotted. The fixing screws clamp down on these slotted tabs. With the screws loosened you can now pull the console clear of the dashboard and begin to disconnect the radio, switch connections etc.
Dismantling the Td5 Radio Console
Remove the multiplug connectors from the back of the switches by squeezing
their securing tabs to release. Each multiplug is keyed to its respective
switch so it will only fit back onto its corresponding switch.
Release the switches from the console by pushing them outwards from the back
of the console.
Remove the full-width switch retainer housing from the back of the original
radio console and transfer it over to the MUD Td5 Double DIN Console. Secure
to the Double DIN Console by reusing the original screw fixings. Refit the
switches into the MUD Td5 Double DIN Console in their respective locations.
If you have a headlamp levelling switch installed, pull off the rotary knob to
reveal the securing nut underneath. Undo the nut to release the levelling
switch from the console.
If you don’t have a headlamp levelling switch, simply transfer the blanking plug across to the Double DIN Console.
The cigarette lighter socket is the trickiest part to remove. To release the factory socket, look for the two square openings down inside the body of the socket. Price back the green plastic locating pegs from the two square openings one side at a time whilst at the same time pushing on the back of the socket. It’s tricky but it can be done! With the socket pushed halfway through the green plastic bezel, it will be enough to release it from the fascia. Place the socket into the new fascia and push the socket body fully back through the green bezel.
It is very common for the plastic bulb holder to have become hard and brittle
over time due to the heat generated by the bulb. This normally results in the
locating tabs breaking when you try to release them. Providing the earth
contact on the bulb holder maintains contact with the body of the Rav socket,
a wrap of insulating tape to hold the bulb holder to the socket will ensure
the socket will continue to illuminate.
The hole for the cigarette lighter in the MUD Td5 Double DIN Console is the
same diameter as the factory panel. We have however increased the diameter of
the recess surrounding the cigarette lighter on the MUD Td5 Double DIN console
to accommodate the slightly larger mounting frame of the popular aftermarket
USB/i2v power sockets, e.g. Blue Sea. When installed, aftermarket power
sockets will sit flush within this recess. If you are upgrading to an
aftermarket socket you will need to increase the diameter of the hole in the
console very slightly to accommodate the increase in the diameter of the
aftermarket sockets. This difference in size is the depth of the thread on the
aftermarket sockets.
Using a pair of side cutters, remove the plastic bag from the dashboard molding to accommodate the extra depth of your Double DIN head unit.
When the switches, headlamp leveling switch, power socket, and radio mounting cage have all been installed, you are now ready to install the MUD Tc15 Double DIN Console back into your vehicle. Replacement of the MUD Td5 Double DIN Console is the exact reversal of removal.
Tel: +44 (o) 1422 881951
Email: mud@mudstuff.co.uk
Web: www.mudstuff.co.uk
01/20/v1
Documents / Resources
| MUD
UK MUD-0069 Double DIN Td5
Console
[pdf] Installation Guide
MUD-0069 Double DIN Td5 Console, MUD-0069, Double DIN Td5 Console, DIN Td5
Console, Td5 Console, Console
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>