SUNCLEANSE Shower Faucet Set with Tub Spout Instruction Manual
- May 15, 2024
- SUNCLEANSE
Table of Contents
SUNCLEANSE Shower Faucet Set with Tub Spout
CERTIFICATE OF LISTING
IAPMO RESEARCH AND TESTING, INC.
CERTIFICATE OF LISTING
IAPMO RESEARCH AND TESTING, INC.
CERTIFICATE OF LISTING
This certificate is not evidence of current listing.To verify listing status, visit the IAPMO R&T Product Listing Directory at pld.iapmo.org
Identification:
Plumbing supply fittings shall be marked with the manufacturer’s recognized
name, trademark, or other mark or, in the case of private labeling, the name,
trademark or other mark of the customer for whom the fitting was manufactured.
The marking shall be accomplished by use of a permanent mark or by placing a
permanent label on the product. Markings on plumbing supply fittings shall be
visible after installation.
Showerheads and hand-held showers shall be marked with the manufacturer’s
specified maximum flow rate, in Umin and gpm.
Kitchen, lavatory, and metering faucets shall be marked with the
manufacturer’s specified maximum flow rate, in L/min and gpm or Ucycle and
gpc.
Single-handle and single-control bath and shower mixing valves shall have
their temperature control settings identified alphabetically, numerically, or
graphically.
High-efficiency commercial pre-rinse spray valves shall be marked with the
manufacturer’s specified maximum flow rate, in L/min (gpm).
Listed products shall bear the cUPC® certification mark.
Packaging for plumbing supply fittings shall be marked with the manufacturer’s
name, trademark, or other mark as well as the model number or, in the case of
private labeling, the name, trademark, or mark of the customer for whom the
fitting was manufactured as well as the model number.
Packaging for showerheads and hand-held showers shall be marked with the
manufacturer’s specified maximum flow rate and either the manufacturer’s
specified minimum flow rate or the statement “For use with automatic
compensating valves rated at xxx L/min (yyy gpm) or less”, where xxx L/min
(yyy gpm) is the manufacturer’s specified minimum flow rate.
Packaging for kitchen, lavatory, and metering faucets shall be marked with the
manufacturer’s specified maximum flow rate, in L/min and gpm or L/cycle and
gpc.
Characteristics
Fittings may include lavatory, sink, bath & shower, lawn and sediment faucets.
Plumbing fixture fittings to be installed in accordance with the
manufacturer’s instructions and the requirements of the latest edition of the
Uniform Plumbing Code and National Plumbing Code of Canada.
Products listed on this certificate have been tested by an IAPMO R& T
recognized laboratory. This recognition has been granted based upon the
laboratory’s compliance to the applicable requirements of 1S0/IEC 17025.
Accessories List
Warning: There are small parts in this product, please keep children away. Do not swallow to avoid choking.
Rough-In Installation
Step 1: Install shower valve
Size of the valve
NOTE
- The depth of chisel wall for reference only.The actual depth is based on the customer’s actual demand.
Step 2: Install pipe
- A. Clean the pipe to make sure there is no sand, embroidery to block the valve before installing.
- B. Wrap 7-10 circle of waterproof tape and tighten clockwise. Tip:Do not rotate back during installation, otherwise the connector will leak
Step 3: Setup connection to shower arm
- The length of the joint should be 1 /5 in the wall.
Step 4: Test valves and piping
- Test whether the shower valve is working properly before sealing the wall and check if there is any water leakage at the joint
- Plug these two joints, running the shower system about 48 hours, and check for leaks.
Step 4: Seal the wall and install shower arm and shower head
Step 5: Install bathtub faucet
Tips
- If you want to adjust the water pressure, you can do this.
- Adjust the red collar to limit the water flow and temperature.
- Turn clockwise to reduce water pressure until it closes. Unscrew the water pressure will increase.
Warranty
Three: About Warranty
Information
Warranty
- This warranty is only valid for product purchase from our store
- Please read the instruction carefully before use.
- Within five years from the date of purchase, the company will repair or replace the same type of product to customer who puncher our product, if product is damaged due to poor materials and workmanship.
- Quality guarantee
- All of product from our store have been carefully manufactured and through the quality standards certification.
- The warranty period
- Within five years from the date of purchase
- If any of the following occurs, consumers will not be able to enjoy the warranty service (that is, the warranty does not apply):
- Damage to products caused by improper use, (whether by mistake, by contractor, by the trade, or by the user’s family)
- The Company is not responsible for the cost of engaging maintenance personnel and for any damage resulting from the installation, repair or replacement of parts, and consequently the resulting damage.
- The lack of water pressure, excessive water impurities and improper use and cleaning caused by the problem will not be covered. The warranty does not cover the cost of repair and parts not listed, nor does it include installation costs.
- Normal wear and tear caused by changes in the water. Loss of normal care – such as regular care need to regularly replace the washers and seals
- During the warranty period, our company provides services based on the severity of the product’s defect or the seriousness of the quality problem
- The warranty period, the product quality problems, the consumer should take the following measures:
- Timely contact with the customer, we will answer for you within 24 hours.
Clean And Maintain The Product
How to clean shower head nozzles
- Just rub the nozzles with your finger or a toothbrush to loosen any deposits, and then run hot water for a few minutes
- Put the showerhead into a pot. Consider using a smaller container that just about fits the showerhead; this way, you will use less vinegar. You can also use a small bucket or plastic bin.
Fill the pot with enough white vinegar to cover the showerhead. The acids in
the vinegar will help dissolve the white mineral deposits on the showerhead.
Let the showerhead soak in the vinegar for 30 minutes The more soiled the
showerhead is, the longer you will have to leave it in the vinegar.
Maintain Chrome and Brushed nickel finished product
- To clean the products all you need is a high quality microfiber cloth.
- Apply a high quality chrome cleaner to a clean cotton cloth, and wipe over the chrome. Leave as per product instructions, and then rinse with warm water. Gently remove any product residue using a dry chamois or paper towel.
- How to Clean Chrome: Homemade Solutions
- In addition to professional products, homespun solutions also have their place when breathing new life into dull chrome. Try this shortcut to achieving chrome cleaning nirvana:
- Detergent and warm water! Submerge chrome-plated objects including pots and pans in a sink full of warm water. Add a halfcup of a high quality washing up detergent (Persil washing up liquid is good) and rub gently with a soft cotton cloth to avoid scratching the chrome. Use a scented detergent to leave kitchenware smelling fresh, as well as spotless.
Contact
- No.1305, 13/F, Hengfeng Tower, 140 Bada Rd., Xingtang Community, Guancheng Street, Dongguan City Guangdong Province, China 523000
- Email: suncleanse@sun-cleanse.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>