Siminda Crystal Shell Pendant Lamp Chandelier User Guide

USE AND CARE GUIDE
Installation or Assemble Instructions
Model No: crystal chandeliers USE AND CARE GUIDE
crystal chandeliers

Safety Infromation

1. To reduce the risk of electric shock the electricity has been turned off at the circuit breaker or fuse box bet0re begin
2. All wing must be in accordance with the National Electrical Code NASI/ NFPA 70. 1999 and local electrical codes Electrical installion should be performed by a qualified licensed electrician
3. The outlet box and bracket support structure must be securely mounted and capable of reliably supporting 66lb (30kg) 0 more
4. The Chandler must be mounted withe mairmumn ot (2mn) clearance from the ceiling edge of the to the floor
5. The chandelier has ts own dimmer and cannot be used together wt your own dimmer (to avoid short circuit)
6. Do not place obits in the path of th Fixtures
7. To void personal injury or damage to the chandelier ad other tens, please be careful wen working around or cleaning the chandelier
8. Electrical diagrams are for reference only Light its that are not packed wt the chandelier must be UL Test Report and marked suable for u with the model chandehr that you are installing Switches must be UL General Use Switches Refer to the instructions packaged with the bight its and switches for proper ass001b
9. After making electrical connections $p/iced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment­ grounding conductor on one side of the outlet box
10. All setscrews must be checked and retightened where necessary before installation

Remote control manual

Basic operation instructions:

1. Code alignment: The remote control can only be used after code alignment operation with the driver. The method is as follows:After connecting the driver to the load lamp (light source) and the power supply, switch on the power supply. At the moment of switching on the power supply (seePress (ON) within 3 seconds after the light/light source is on. When you see that the light (light source) will “flash three times slowly”, that is, the code and grouping is successful.
2. Clear the code, the method is as follows: select the lamp that needs to clear the code, cut off the power. reconnect the power, after connecting the power light Within 3 seconds), press the main open button five times, that is, the lamp/light source will “flash six times”, to confirm the success of code clearing.

STEP 9 Check
Congratulation, you have completed the installation for your chandelier! One last thing to do is to check it from a distant just to make sure that the crystal chandelier  is leveled and at proper height. Make additional small adjustment as needed. After ensuring safety, you can turn on your house’ s power switch and the light switch for the crystal chandelier. Now you can enjoy the beautiful chandelier that you just installed for your home

STEP 1.Peparation
Make sure that all the parts that you need for the product are available based on the instruction before starting the chandelier installation process. Also, we do recommend you have the electrician test the chandelier on the ground before installing it to the ceiling just to ensure that there is no damage during shipping.

1. The tools you need
   Ladder, pliers, wire strippers, screwdrivers, power drill(optional), a drill bit(optional)

2. Turn off the power Tips: To ensure safety, you can test with a measuring pen, or you can turn on the light switch to make sure the power is off.
   Place mounting bracket on ceiling and mark out the points where you need to drill holes.

Installation instruction of crystal ball

Step 4:Installa the crystal string
In order to save your time, this chandelier is in a spiral shape from the factory.
The hanging wire has been adjusted,

Arrange crystals
we have arranged the shapes of the lamps in a spiral state. If you need to mess up the shape, you can adjust the length of the hanging wire to achieve the shape you want.

Step 2: Install the Mounting Bracket
Insert the machine screws into the mounting bracket.

Step 3: Connect Wire and install the Conn copy
Most chandeliers have black and white lines. Connect the blak/’brown wire to the live wire, the white/blue wire to the neutral wire, and the yellow/green wires to the ground wire (optional). Attach the stripped end of the black power cord with the stripped end of the black/brown wire of the chandelier and screw them together  with a wire nut. Do the same for the white/blue wire with the white power cord9Connect the wires based on the instruction above and attach canopy to the mounting bracket with bolt cap (provided)

Please refer to the light bulb information provided for the product on the instruction or on our website to select the correct light bulb type. The product will require a specific type of light bulbs, like GU10. You can choose LED or halogen light bulbs based on your preference. You can also decide what kind of color temperature that you want for the light bulbs, like daylight or warm white. In addition, you can even choose different colors for the light bulbs, like blue, yellow or green. lf you need to replace the bulb, must remove the old bulb and transformer together,

FCC Warnning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>