GOLD LEAF DESIGN GROUP T-Lock Point Security Hanger Instruction Manual
- May 15, 2024
- GOLD LEAF DESIGN GROUP
Table of Contents
GOLD LEAF DESIGN GROUP T-Lock Point Security Hanger
Specifications
- Includes: Wall Bracket, Artwork Plate
- Material: Metal
- Recommended Tools: Pilot holes, screws, wrench
- Manufacturer: Gold Leaf Design Group, Inc.
- Contact: 1300 S. Kostner Avenue Chicago, IL 60623 | 312.738.1790 | [email protected]
Product Usage Instructions
Attaching Artwork Security Plates
- Begin by attaching the artwork security plates to the back of the artwork.
- Pilot holes are suggested for easier installation.
Attaching Slotted Plates
- On the top of the artwork, attach two slotted plates using six (6) 1/2 screws.
- Ensure the plates are attached inset to the top corners and level with each other.
- On the bottom of the artwork, attach one slotted plate to the center of the frame using the same screws.
Hanging the Artwork
- Hang the artwork by sliding the frame down onto the two installed wall brackets, catching the top plates on the back of the artwork.
- Mark the wall where the center of the bottom plate is attached to the back of the artwork.
Locking the Artwork
- Using a hardened wrench, go underneath the bottom of the artwork and turn the head of the T-screw a 1/4 turn to lock the artwork to the wall.
Finalizing Installation
- Remove the artwork from the wall, drill a hole 5/16 above the pencil mark, insert a plastic anchor, and screw the T-screw into the anchor.
- Leave the T-screw extending from the wall about 3/8 and rotate it horizontally.
- Finally, replace the artwork on the wall suspended by the wall brackets.
FAQs:
Q: What tools are recommended for installing the T-Lock Point Security Hanger?
- A: It is recommended to use pilot holes, screws, and a hardened wrench for proper installation.
Q: How should I position the slotted plates on the artwork?
- A: The top plates should be attached inset to the top corners and level with each other, while the bottom plate should be attached to the center of the frame.
INSTALLATION INSTRUCTION
ALWAYS USE PROPER TOOLS. Begin by attaching the artwork security PLATES first.
- ARTWORK BACK- Pilot holes are suggested. TOP of artwork, attach two slotted PLATES (using the six (6) 1/2″ screws).
- The PLATES at the top should be attached inset to the top corners and level with each other.
- BOTTOM of artwork, attach one slotted PLATE to the center of the frame. Use the same screws.
- WALL BRACKET- Decide placement and hanging height of the artwork. To install the 2 wall BRACKETS, the distance between the 2 artwork PLATES must first be measured.
- The distance between the LEFT screw of the LEFT upper PLATE and the LEFT screw of the RIGHT upper PLATE is the distance between the centers of the two PLATES (see X”).
- Install the 2 wall BRACKETS using the X” measurement center to center. Make sure that the BRACKETS are level with each other.
- Small adjustments to level the artwork can be made by slightly loosening the screws, nudging the WALL BRACKET in the direction to achieve levelness, then tighten screws.
- WALL T-SCREW- Hang the artwork by sliding the frame down onto the 2 installed wall BRACKETS catching the top.
- PLATES on the back of the artwork. Using a pencil, lightly mark the wall where the center of the bottom PLATE is attached to the back of the artwork.
- Remove the artwork from the wall. Measure 5/16″ above the pencil mark, drill a hole, and insert the plastic anchor. Screw the T-screw into the plastic anchor.
- Leave the T-screw extending from wall about 3/8″ and rotate the head of the T-screw in a horizontal position.
- Replace the artwork on the wall suspended by the wall BRACKETS. The head of the T-screw should now pass through the bottom PLATE on the back of the artwork.
- Using your hardened wrench, go underneath the bottom of the artwork and turn the head of the Tscrew a 1/4 -turn to lock the artwork to the wall.
SIDE VIEW
- Gold Leaf Design Group, Inc.
- 1300 S. Kostner Avenue
- Chicago, IL 60623
- 312.738.1790 t
- [email protected]
- gldg.net
Documents / Resources
| GOLD
LEAF DESIGN GROUP T-Lock Point Security
Hanger
[pdf] Instruction Manual
T-Lock Point Security Hanger, T-Lock, Point Security Hanger, Security Hanger,
Hanger
---|---
References
Read User Manual Online (PDF format)
Loading......