hogart 10002 Electric Faucet with Instant Water Heating Function Instruction Manual
- May 15, 2024
- hogart
Table of Contents
Hogarth 10002 Electric Faucet with Instant Water Heating Function
Instruction Manual
PRODUCT PARTS
- Faucet body
- Faucet base
- Spout
- Water inlet
- Aerator
- Temperature and flow control handle
- Power cord with plug
- Clamp nut
- Temperature indicator
PRODCUT DATA SHEET
READ THE OPERATING MANUAL BEFORE USE
Mains voltage and frequency : Supply water pressure
UMWELTSCHUTZ Dieses Symbol
ENVIRONMENTAL PROTECTION Correct disposal of this product: This marking shown on the product and its literature indicates this kind of product mustn’t be disposed with household wastes at the end of its working life in order to prevent possible harm to the environment or human health. Therefore the customers is invited to supply to the correct disposal, differentiating this product from other types of refusals and recycle it in responsible way, in order to re – use this components. The customer therefore is invited to contact the local supplier office for the relative information to the differentiated collection and the recycling of this type of product.
PRODUCT CHARACTERISTICS
Electric faucet with instant water heating function produces a hot water everywhere you need. Simply bring the running cold water and connect the faucet to electricity. Instant heating element, will provide you hot water in 5 seconds.
Before using the product, you should read all the instructions and keep it during all time of use.\
The manufacturer is not responsible for any damage caused by failure to comply with safety regulations and instructions of this manual.
EQUIPMENT
The product is supplied in a complete set but it requires the installation steps, which are described later in this manual.
SAFETY INSTRUCTIONS
Attention! Before connecting the product to mains, you should make sure, that the mains parameters will be sufficient to supply the product. Before connecting the product to mains, you should make sure that voltage, the frequency and the performance of the mains correspond to the values on the rating plate of the product. Power cable plug must fit into the mains socket. It is forbidden to disassemble the plug and cable.
- The product must be connected directly to a single wall mains socket. it is forbidden to use extension cables, splitters, and double sockets. Circuit power supply network must be equipped with a grounding conductor and protection for 16 A.
- Avoid contact of the power cable with sharp edges and hot objects and surfaces. When the product is working, the power cable must always be fully unwinder, and its location should be set so, it would be no obstacle during the operation of the product. Placing the power cable can cause a tripping hazard so please be careful. The power outlet should be located in such a place, that there would be always possible to quickly disconnect the power cable plug.
- The socket should be located possibly far away from water outlet. When disconnecting the power cable plug, you should always pull by the plug housing, never by the cable. If the power cable or plug are damaged, you should immediately disconnect them from the mains and contact authorized service of the manufacturer for replacement. Do not use the product with a damaged cable or plug. The power cable or plug can not be repaired, in the event of a failure of these elements they should be replaced with new ones.
- Before connecting the product to mains, you should make sure, that the water pressure is within the range specified in the table technical data and on the rating plate of the product.
- It is recommended that the product connection to the water supply will be performed by a qualified personnel.
- The product designed for only an indoors installation. The product should be not mounted at places, where the temperature will fall to the level which would cause freezing of water. Frozen water increases in its volume, that can lead to a damage of the product.
- If you noticed any damage to the product, it is prohibited to use it. All damage must be removed before resuming use of the product.
PRODUCT ASSEMBLY
Attention! The first step should be the connection of the product to the water source, and checking the tightness of the water connections, and only then the product should be connected to an electrical power supply. It is forbidden to mount the product, which is connected to mains.
Attention! The product designed only for a vertical installation. It is forbidden to mount the product in any different position.
You should mount to the faucet body with spout first. Alter, you should check whether all gaskets and the resistance ring are located in the caving’s of the spout mounting. Then, without a usage of any tools, you should screw a fixing collar on the threaded body of the faucet body (II. Correctly mounted drain spout should smoothly rotate in the angle of 360 degrees, with slightly a perceptible resistance.
The faucet body should be mounted in the hole near the sink, of the wash basin so that water may have no obstacles to get to the drain plumbing.
Place a black rubber gasket under the faucet base, this will protect the mounting place from damage. Fasten the faucet body by screwing the fixing nut. It is recommended to tighten the fixing nut without the use ofany tools, however, if it does not provide a stable body mounting of the faucet, you can use the wrench to tighten. You should be careful when tightening the nut with a wrench because it is made of plastic and can be destroyed by applying too much for
Attention! Before connecting the product to a central water pipe, you should make sure, that the water supply is off.
-
You should connect the water inlet using the flexible pipe.
Make sure, that faucet flow control handle is in closed position, then open the water supply to the faucet. Make sure, that water supply shows no traces of the leaks and then open the faucet flow control handle, by turning the valve up or down. The water should outflow from the spout. Check whether the spout connection and the faucet are showing any traces of leaks. -
If you detect any leaks, you should close the water supply to the faucet, and then remove the cause of the leaks and again check the tightness of connections.
Aſter the checking the leakage of water connections, you may connect the faucet to the electrical power supply. -
Make sure, that the faucet control handle is closed, and that the outlet spout is not producing any water, then insert the plug of the power cable to the mains socket. Open the faucet flow control handle by turning it down, the water outlet should produce hot water. At the same time, the temperature indicator will turn on at the body of the faucet, which means start of the water heating.
USE OF THE PRODUCT
Attention! The faucet with instant water heating function can produce water at very high temperature, higher than the normal operating temperature of hot water in the water supply. You should exercise caution, to avoid burning up during the heater operation.
The position of flow control handle regulates the intensity of the water stream. The more the valve is opened, the handle is closer to the extreme position, the more intense the water flow is produced from the spout.
HOWEVER, BECAUSE IT IS EASIER TO HEAT LESS INTENSE STREAM OF WATER, THE HIGHER INTENSE IS THE STREAM, THE LOWER IS THE WATER TEMPERATURE.
The heating element switches on automatically when you open the flow control handle and rotate it down. The heating element switches off automatically when you close the valve
Attention! When you do not use the electric faucet for an extended period of time, you should disconnect it from the electrical power supply. Remove the plug from the mains socket.
MAINTENANCE OF THE PRODUCT
Attention! All maintenance operations must be carried out when the faucet electric power supply is turned off. You should unplug the electric faucet from the mains outlet.
- Faucet body, spout, and other parts, which are made of plastic, should be cleaned using a sort cloth and the cleaning products, which are intended for the maintenance of plastic. Alter the cleaning, you should wipe the body with assort cloth soaked in water, and then dry or let it for drying.
- Chrome-plated parts should be cleaned like plastic parts, but with the use of appropriate cleaning agents.
- It is forbidden to use aggressive detergents for the product maintenance. It is forbidden to use any abrasive agents, as well as cleaning agents, which are containing alcohol, acids (except for the 2% solution of vinegar with water).
- Water supplied to the faucet must be cleaned from all mechanical and chemical impurities. The manufacturer is not responsible for mixer faucet damages due to contamination of water.
- If the intensity of the water stream will be reduced It may be due to the clogging of water in the outlet from the spout.
Attention! Before the start of the following maintenance activities, you should close the water supply to the faucet. In order to clear the faucet water inlet mesh filter you should unscrew the heater body from the connection pipe, which is fixing the strainer, and then the same strainer. Clean all elements with a stream of running water and install them in reverse order to their disassembly. Perform a leak test of water connections before connecting the product to the power supply.
In order to ensure patency of the water outlet of spout, you should unscrew the aerator and check its patency. Check the condition of the gasket and, if necessary, clean up both elements with a stream of running water. Then mount the gasket and screw the aerator without the use of tools. Perform a leak test of water connections before connecting the product to the power supply.
REMARKS
The heating varies from 25 to 50 degree Celsius, and depends on several factors:
- Pressure of the water flow. Bigger is the water flow, the lower will be the temperature, and opposite, the lower is the water flow – the higher will be the temperature. You can operate this by adjusting the water flow handle on the device.
- Temperature of inlet water. In the cold winter period, when the inlet water is colder the maximum temperature of water heating may be lower than usual, reaching no more than 30-40 degrees.
Attention: When the water flow is too low, the heating speed is very fast and may soon reach 50-70 degrees Celsius. Families with children and the elderly should pay attention to the fact that improper use may cause burns.
Every device is 100% brand new. Each item is being tested before final packing. If You will find some water inside the heater, that means the product has been checked and passed leakage QC.
POSSIBLE MALFUNCTIONS
-
In the event of a malfunction, we recommend that you take the following actions
-
Fault: No water comes out of the faucet, or the water flow is less than normal.
-
Solution: Check the faucet aerator for dirt. Rinse under running water if necessary. Install back on the mixer spout.
-
Solution: Check the dirt filter installed at the cold-water inlet. Rinse under
running water if necessary and reinstall. -
Fault: Heating does not work; the display does not show the temperature of the heating water.
-
Solution: Check the operating pressure in the water supply system. If the pressure is less than 0.5 bar. water heating will not work. Increase system pressure to the minimum required.
-
Solution: Check the power outlet and mains fuse, they may have
IF THE ABOVE MEASURES DO NOT WORK, OR YOU HAVE OTHER QUESTIONS CONCERNING
OPERATING THE DEVICE, PLEASE CONTACT US.
Documents / Resources
|
hogart 10002 Electric Faucet with Instant Water Heating
Function
[pdf] Instruction Manual
10002 Electric Faucet with Instant Water Heating Function, 10002, Electric
Faucet with Instant Water Heating Function, Instant Water Heating Function,
Water Heating Function, Heating Function
---|---